Samsung ML-3050 - Manual

i Important Precautions and Safety Information When using this machine, these basic safety precautions should always be followed to reduce risk of fire, electric shock, and injury to people:1 Read and understand all instructions. 2 Use common sense whenever operating electrical appliances. 3 Follow ...

ii Recycling Please recycle or dispose of packaging materials for this product in an environmentally responsible manner. Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) Thi...

iii A full declaration, defining the relevant Directives and referenced standards can be obtained from your Samsung Electronics Co., Ltd. representative. EC Certification Certification to 1999/5/EC Radio Equipment & Telecommunications Terminal Equipment Directive (FAX) This Samsung product has b...

iv Replacing the Fitted Plug (for UK Only) Important The mains lead for this machine is fitted with a standard (BS 1363) 13 amp plug and has a 13 amp fuse. When you change or examine the fuse, you must re-fit the correct 13 amp fuse. You then need to replace the fuse cover. If you have lost the fuse...

1 .1 <Introduction> 1 Introduction Congratulations on the purchase of your printer! This chapter includes: • Special features • Printer overview • Finding more information Special features Your new printer is equipped with several special features that improve the print quality. You can: Print...

1 .2 <Introduction> Printer features The table below lists a general overview of features supported by your printer. (I: Installed, O: Option, NA: Not Available) Features ML-3050 ML-3051N ML-3051ND IEEE 1284 Parallel I I I USB 2.0 I I I Network Interface(Ethernet 10/100 Base TX) NA I I Wireles...

1 .3 <Introduction> Rear view 1 control board cover 6 duplex unit 2 network port 7 power receptacle 3 USB port 8 power switch 4 parallel port 9 rear cover 5 optional tray 2 cable connector * The figure above shows an ML-3051ND with all available options. Control panel overview ML-3050 ML-3051N...

1 .4 <Introduction> Finding more information You can find information for setting up and using your from the following resources, either printed or onscreen. Quick Install Guide Provides information on setting up your printer and, therefore, be sure to follow the instructions in the guide to g...

2 .1 <System setup> 2 System setup This chapter provides step by step information on setting up your printer. This chapter includes: • Using control panel menus (ML-3051N, ML-3051ND only) • Menu overview • Printing a demo page • Changing the display language (ML-3051N, ML-3051ND only) • Using ...

2 .3 <System setup> Paper menu Use the Paper menu to define all settings relating to print material input and output, as well as the specific print material you are using with your printer. Item Explanation Copies Set the default number of copies by selecting any number from 1 to 999. Paper Si...

2 .5 <System setup> PCL This menu sets the PCL emulation configuration. You can set the font type, symbol type, lines per page, and point size. Item Explanation Typeface You can select the standard font to be used in PCL emulation. • PCL1~PCL7’s interval between letters is fixed, and PCL8~PCL4...

2 .6 <System setup> Network menu This menu lets you configure the network interface installed in your printer. You can reset the network interface and print a configuration page. Item Explanation TCP/IP This item allows you to manually set the TCP/IP addresses or receive the addresses from the...

2 .7 <System setup> Using toner save mode Toner save mode allows the printer to use less toner on each page. Activating this mode extends the life of your toner cartridge and reduces your cost per page beyond what one would experience in the normal mode, but it reduces print quality. This sett...

3 .1 <Software overview> 3 Software overview This chapter gives you an overview of the software that comes with your printer. Further details about installing and using the software are explained in the Software Section . This chapter includes: • Supplied software • Printer driver features • S...

3 .2 <Software overview> Printer driver features Your printer drivers support the following standard features:• Paper source selection• Paper size, orientation and media type• Number of copies In addition, you can use various special printing features. The following table shows a general overv...

3 .3 <Software overview> Linux Notes • It is necessary to claim swap partition of 300 MB or larger for working with large scanned images. • The Linux scanner driver supports the optical resolution at maximum. Macintosh Item Requirements Operating system • Red Hat 8.0 ~ 9.0 • Fedora Core 1 ~ 3 ...

4 .1 <Network setup> 4 Network setup This chapter gives you step-by-step instructions for setting up your printer for network connections.This chapter includes: • Introduction • Supported operating systems • Configuring TCP/IP • Configuring EtherTalk • Configuring IPX frame types • Setting Eth...

5 .1 <Loading print media> 5 Loading print media This chapter will help you understand types of paper you can use with your printer and how to properly load paper in the different paper trays for the best print quality. This chapter includes: • Selecting print media • Loading paper • Selecting...

5 .2 <Loading print media> Supported sizes of paper Note For duplex printing, A4, Letter, Oficio, Legal, and Folio sizes are supported. Type Size Dimensions Weight a a. If media weight is over 24 lb (90 g/m 2 ), use the multi-purpose tray. Capacity b b. Maximum capacity may differ depending on...

5 .3 <Loading print media> Guidelines for selecting and storing print media When selecting or loading paper, envelopes, or other print materials, keep these guidelines in mind:• Always use print media that conform with the specifications listed on page 5.3. • Attempting to print on damp, curle...

5 .4 <Loading print media> Transparencies • To avoid damaging the printer, use only transparencies designed for use in laser printers. • Transparencies used in the printer must be able to withstand 200° C (392° F), the printer’s fusing temperature. • Place them on a flat surface after removing...

5 .5 <Loading print media> Using the tray 1 or the optional tray 2 Use the print material you use for the majority of your print jobs in the tray 1. The tray 1 can hold a maximum of 250 sheets of 75 g/m 2 paper. You can purchase an optional tray 2 and attach it below the tray 1 to load an addi...

5 .6 <Loading print media> Notes • Do not push the paper width guide far enough to cause the material to warp. • If you do not adjust the paper width guide, it may cause paper jams. Using the multi-purpose tray The multi-purpose tray can hold special sizes and types of print material, such as ...

5 .7 <Loading print media> 5 When you print a document, set the paper source and type in the software application. See the Software Section . For information about setting the paper source and type on the control panel, see page 2.3. 6 After printing, fold the multi-purpose tray extension and ...

5 .8 <Loading print media> Selecting an output location The printer has two output locations; the rear cover (face up) and the output tray (face down). The printer sends output to the output tray by default. To use the output tray, make sure that the rear cover is closed. Notes • If paper comi...

6 .1 <Basic printing> 6 Basic printing This chapter explains common printing tasks. This chapter includes: • Printing a document • Canceling a print job Printing a document This printer allows you to print from various Windows, Macintosh, or Linux applications. The exact steps for printing a d...

7 .1 <Ordering supplies and accessories> 7 Ordering supplies and accessories This chapter provides information on purchasing toner cartridges and accessories available for your printer. • Toner cartridges • Accessories • How to purchase Toner cartridges When the toner runs out, you can order t...

8 .1 <Maintenance> 8 Maintenance This chapter provides information for maintaining your printer and the toner cartridge , as well as suggestions for high-quality and economical printing.This chapter includes: • Printing information page • Cleaning the printer • Maintaining the toner cartridge ...

8 .2 <Maintenance> 4 Locate the long strip of glass (LSU) inside the top of the cartridge compartment, and gently swab the glass to see if dirt turns the white cotton black. 5 Reinsert the toner cartridge and close the front cover . 6 Plug in the power cord and turn the printer on. Printing a ...

8 .3 <Maintenance> Redistributing toner cartridge When the toner cartridge is near the end of its life: • White streaks or light printing occurs. • Toner Low appears on the display . ( ML-3051N , ML-3051ND only) • The Smart Panel program window appears on the computer telling you that the tone...

8 .4 <Maintenance> 3 Remove the new toner cartridge from its bag. Caution Do not use sharp objects, such as a knife or scissors, to open the toner cartridge package. They might scratch the drum of the cartridge. 4 Remove the packing tape and roll the cartridge 5 or 6 items to distribute the to...

9 .1 <Troubleshooting> 9 Troubleshooting This chapter provides helpful information for what to do if you encounter an error while using your printer. This chapter includes: • Clearing paper jams • Troubleshooting checklist • Understanding the Status LED • Understanding display messages • Toner...

9 .3 <Troubleshooting> Around the toner cartridge Note The fuser area is hot. Take care when removing paper from the printer. 1 Open the front cover and pull the toner cartridge out. 2 Remove the jammed paper by gently pulling it straight out. 3 Replace the toner cartridge and close the front ...

9 .4 <Troubleshooting> 5 Release the blue strap, the rear cover stopper, and fully open the rear cover, as shown. 6 Unfold the duplex guide fully. 7 While pushing the fuser lever to the right, open the fuser door. 1 rear cover stopper 2 rear cover 2 1 1 duplex guide 1 1 fuser lever 2 fuser doo...

9 .5 <Troubleshooting> 2 Remove the jammed paper from the duplex unit. If the paper does not come out with the duplex unit, remove the paper from the bottom of the printer. Duplex jam 1 1 Open the rear cover. 2 Unfold the duplex guide fully. 1 1 duplex guide 3 Pull the jammed paper out. Tips f...

9 .7 <Troubleshooting> Understanding display messages Messages appear on the Smart Panel program window or the control panel display to indicate the printer’s status or errors. Refer to the tables below to understand the messages’ meaning and correct the problem if necessary. Messages and thei...

9 .8 <Troubleshooting> Toner cartridge-related messages Message Meaning Suggested solutions Install Toner A toner cartridge is not installed. Install a toner cartridge . Invalid Toner The toner cartridge you have installed is not for your printer. Install a Samsung -genuine toner cartridge , d...

9 .9 <Troubleshooting> Solving general printing problems For problems with the operation of your printer, refer to the table for suggested solutions. Condition Possible cause Suggested solutions The printer does not print. The printer is not receiving power. Check the power cord connections. C...

9 .13 <Troubleshooting> Common Windows problems Note Refer to Microsoft Windows 9x/Me/NT 4.0/2000/XP/2003 User’s Guide that came with your PC for further information on Windows error messages. Curl If the printed paper is curled or paper does not feed into the printer:• Turn over the stack of ...

10 .1 <Installing accessories> 10 Installing accessories Your printer is a full-featured laser printer that has been optimized to meet most of your printing needs. Recognizing that each user may have different requirements, however, Samsung makes several accessories available to enhance the pr...

10 .3 <Installing accessories> 3 Align the connector on the wireless network interface card with the connector on the control board. Push the card firmly into the connector on the control board until it is completely and securely in place. 4 Replace the control board cover. 5 Reconnect the pow...

11 .1 <Specifications> 11 Specifications This chapter includes: • Printer specifications Printer specifications Item Specifications and Description Model name ML-3050, ML-3051N, ML-3051ND Printing speed a 28 ppm (A4); 30 ppm (Letter) Duplex: 19 ipm (A4); 21 ipm (Letter) Resolution Up to 1200 x...

1 I NDEX A accessories installing memory DIMM 10.1 wireless network interface card 10.2 order information 7.1 C cleaning drum 8.2 inside 8.1 outside 8.1 cleaning sheet, print 8.2 component location 1.2 configuration page, print 8.1 control panel menus 2.1 status LED 9.6 D demo page, print 2.6 DIMM, ...

Installing Printer Software in Windows 4 1 Installing Printer Software in Windows This chapter includes:• Installing Printer Software• Changing the Software Language• Reinstalling Printer Software• Removing Printer Software Installing Printer Software You can install the printer software for local p...

Installing Printer Software in Windows 5 N OTE : If your printer is not already connected to the computer, the following window will appear. • After connecting the printer, click Next.• If you don’t want to connect the printer at this time, click Next, and No on the following screen. Then the instal...

Installing Printer Software in Windows 10 Changing the Software Language After installation of the software, you can change the display language. 1 Click the Windows Start menu. 2 Select Programs or All Programs and then your printer driver name. 3 Select Language Selection. 4 Select the desired lan...

Installing Printer Software in Windows 11 Removing Printer Software 1 Start Windows. 2 From the Start menu select Programs or All Programs → your printer driver name → Maintenance. 3 Select Remove and click Next.You will see a component list so that you can remove any item individually. 4 Select the...

Basic Printing 12 2 Basic Printing This chapter explains the printing options and common printing tasks in Windows. This chapter includes:• Printing a Document• Printer Settings - Layout Tab- Paper Tab- Graphics Tab- Extras Tab- About Tab- Printer Tab- Using a Favorite Setting- Using Help Printing a...

Basic Printing 13 Printer Settings You can use the printer properties window, which allows you to access all of the printer options you need when using your printer. When the printer properties are displayed, you can review and change the settings needed for your print job. Your printer properties w...

Basic Printing 14 Paper Tab Use the following options to set the basic paper handling specifications when you access the printer properties. See “Printing a Document” on page 12 for more information on accessing printer properties. Click the Paper tab to access various paper properties. Copies Copie...

Basic Printing 15 Graphics Tab Use the following Graphic options to adjust the print quality for your specific printing needs. See “Printing a Document” on page 12 for more information on accessing printer properties. Click the Graphic tab to display the properties shown below.. Resolution The Resol...

Basic Printing 16 Extras Tab You can select output options for your document. See “Printing a Document” on page 12 for more information about accessing the printer properties.Click the Extras tab to access the following feature: Watermark You can create a background text image to be printed on each ...

Basic Printing 17 Using a Favorite Setting The Favorites option, which is visible on each properties tab, allows you to save the current properties settings for future use. To save a Favorites item: 1 Change the settings as needed on each tab. 2 Enter a name for the item in the Favorites input box. ...

Advanced Printing 18 3 Advanced Printing This chapter explains printing options and advanced printing tasks. N OTE : • Your printer driver Properties window that appears in this User’s Guide may differ depending on the printer in use. However the composition of the printer properties window is simil...

Advanced Printing 19 Printing Posters This feature allows you to print a single-page document onto 4, 9, or 16 sheets of paper, for the purpose of pasting the sheets together to form one poster-size document. 1 To change the print settings from your software application, access printer properties. S...

Advanced Printing 20 Printing on Both Sides of Paper You can print on both sides of a sheet of paper. Before printing, decide how you want your document oriented.The options are: • Printer Setting, if you select this option, this feature is determined by the setting you’ve made on the control panel ...

Advanced Printing 21 Using Watermarks The Watermark option allows you to print text over an existing document. For example, you may want to have large gray letters reading “DRAFT” or “CONFIDENTIAL” printed diagonally across the first page or all pages of a document. There are several predefined wate...

Advanced Printing 22 Using Overlays What is an Overlay? An overlay is text and/or images stored in the computer hard disk drive (HDD) as a special file format that can be printed on any document. Overlays are often used to take the place of preprinted forms and letterhead paper. Rather than using pr...

Using Windows PostScript Driver 23 4 Using Windows PostScript Driver If you want to use the PostScript driver provided with your system CD-ROM to print a document.PPDs, in combination with the PostScript driver, access printer features and allow the computer to communicate with the printer. An insta...

Sharing the Printer Locally 24 5 Sharing the Printer Locally You can connect the printer directly to a selected computer, which is called “host computer,” on the network. The following procedure is for Windows XP. For other Windows OS, refer to the corresponding Windows User's Guide or online help. ...

Using Smart Panel 25 6 Using Smart Panel Smart Panel is a program that monitors and informs you of the status of the printer, and allows you to customize the printer’s settings. Smart Panel is installed automatically when you install the printer software. N OTES : • To use this program, you need: - ...

Using Smart Panel 26 Driver Setting (Only for Windows) You can use the printer properties window, which allows you to access all of the printer options you need for using your printer. For details, See “Printer Settings” on page 13. Opening the Troubleshooting Guide Using the troubleshooting guide, ...

Using Your Printer in Linux 27 7 Using Your Printer in Linux You can use your machine in a Linux environment. This chapter includes:• Getting Started• Installing the Unified Linux Driver• Using the Unified Driver Configurator• Configuring Printer Properties• Printing a Document Getting Started The s...

Using Your Printer in Linux 28 Uninstalling the Unified Linux Driver 1 When the Administrator Login window appears, type in root in the Login field and enter the system password. N OTE : You must log in as a super user (root) to install the printer software. If you are not a super user, ask your sys...

Using Your Printer in Linux 29 Printers Configuration Printers configuration has the two tabs; Printers and Classes. Printers Tab You can see the current system’s printer configuration by clicking on the printer icon button on the left side of the Unified Driver Configurator window. You can use the ...

Using Your Printer in Linux 30 Configuring Printer Properties Using the properties window provided by the Printers configuration, you can change the various properties for your machine as a printer. 1 Open the Unified Driver Configurator. If necessary, switch to Printers configuration. 2 Select your...

Using Your Printer in Linux 31 The following four tabs display at the top of the window. •General - allows you to change the paper size, the paper type, and the orientation of the documents, enables the duplex feature, adds start and end banners, and changes the number of pages per sheet. •Text - al...

Using Your Printer with a Macintosh 31 8 Using Your Printer with a Macintosh Your printer supports Macintosh systems with a built-in USB interface or 10/100 Base-TX network interface card. When you print a file from a Macintosh computer, you can use the driver by installing the PPD file. N OTE : Som...

Using Your Printer with a Macintosh 32 Setting Up the Printer Set up for your printer will be different depending on which cable you use to connect the printer to your computer—the network cable or the USB cable. ML-3050 only For a Network-connected Macintosh N OTE : Some printers do not support a n...

Using Your Printer with a Macintosh 33 Printing N OTES : • The Macintosh printer’s properties window that appears in this User’s Guide may differ depending on the printer in use. However the composition of the printer properties window is similar. • You can check your printer name in the supplied CD...

Using Your Printer with a Macintosh 34 Printer Features Setting The Printer Features tab provides options for selecting the paper type and adjusting print quality.Select Printer Features from the Presets drop-down list to access the following features: Reverse Duplex Allows you to select general pri...

Using Your Printer with a Macintosh 35 Duplex Printing You can print on both sides of the paper. Before printing in the duplex mode, decide on which edge you will be binding your finished document. The binding options are: Long-Edge Binding: Which is the conventional layout used in book binding. Sho...