Samsung DW50DG450B00 - Repair Manual

Table of Contents:

• Page 2 – IMPORTANT SAFETY NOTICE; covered by the warranty.; WARNING; version on the barcode label at the left side of the tub.
• Page 3 – Tools For Removal And Reassembly _ 3; TOOLS FOR REMOVAL AND REASSEMBLY; Tool image; Preparation for parts replacement; Pull out the unit from the sink and lay it on the floor.
• Page 4 – _ Standard Disassembly Drawings; STANDARD DISASSEMBLY DRAWINGS; Caution; - Make sure to remove all items include baskets inside dishwasher.
• Page 5 – Standard Disassembly Drawings _ 5; Part; GASKET BRAKE; Warning; Be sure to remove the power plug before servicing.; NOTE; screws, pull the COVER TOP backward first, and take it
• Page 6 – _ Standard Disassembly Drawings
• Page 7 – Standard Disassembly Drawings _ 7; PREPARATION: Remove SIDE PANEL Left & Right refer to; Remove wire connector that connect Main PBA to Sub
• Page 8 – _ Standard Disassembly Drawings; Remove 2 terminals that connected to DETERGENT; Pay attention to hook of terminals.; Pay attention to DOOR drop after remove the rope. It can; Push both ribs of GUIDE HINGE to pull out the DOOR.; Do not this work without safety gloves. It can cause
• Page 9 – Standard Disassembly Drawings _ 9; Do same work at the opposite side, and pull out the DOOR; DOOR HINGE and GUIDE HINGE will serviced to
• Page 10 – 0 _ Standard Disassembly Drawings; Make sure the Wire harness are not getting stuck in
• Page 11 – Standard Disassembly Drawings _ 11; Make sure the Wire harness are not getting stuck in other
• Page 12 – 2 _ Standard Disassembly Drawings; Fasten 6 screws to fix the DOOR OUTER.; Use the Torx® T15 screw driver.
• Page 13 – Standard Disassembly Drawings _ 13; Remove HOLDER ROPE DOOR from the DOOR HINGE left; Pay attention to DOOR drop after remove the rope.; Be careful to avoid injury from the DOOR drop without; Rotate the HOLDER HINGE to release from hook.
• Page 14 – 4 _ Standard Disassembly Drawings; Be careful to touch the BRACKET SEAL TUB after; Pay attention to the direction of seal. If it is assembled in
• Page 15 – Standard Disassembly Drawings _ 15; Press the seal from the top corner toward remaining side.; Pay attention to assemble not to deform the seal tip
• Page 16 – 6 _ Standard Disassembly Drawings; Turn the COARSE FILTER counter-clockwise to unlock
• Page 17 – Standard Disassembly Drawings _ 17; Make sure to reassemble to correct location.
• Page 18 – 8 _ Standard Disassembly Drawings; Put the HOLDER ROTOR LOWER on the SUMP.; Pay attention to assemble the HOLDER ROTOR LOWER
• Page 19 – Standard Disassembly Drawings _ 19; Assemble the ASSY DUCT NOZZLE to hooks and on the
• Page 20 – 0 _ Standard Disassembly Drawings; Open the dishwasher’s DOOR, and take off the BASKET; Be careful not to break the hooks.; To disassemble the ROTOR MIDDLE only, loosen the
• Page 21 – Standard Disassembly Drawings _ 21; Turn the COARSE FILTER counter-clockwise to unlock the; Make sure to direction of MICRO FILTER when reassemble; Reassembly is the reverse order of disassembly.; Make sure the COARSE FILTER is closed securely. A loose
• Page 22 – 2 _ Standard Disassembly Drawings
• Page 23 – Standard Disassembly Drawings _ 23
• Page 24 – 4 _ Standard Disassembly Drawings; Do not force the removal of the basket.
• Page 25 – Standard Disassembly Drawings _ 25; Take off the HOLDER RAIL REAR by pulling back with; Put the RAIL BASKET on the ROLLER RAIL.; Assemble the HOLDER RAIL REAR to RAIL BASKET.
• Page 26 – 6 _ Standard Disassembly Drawings; This part will be serviced by assembly part only.
• Page 27 – Standard Disassembly Drawings _ 27; Release the cap of softener by rotating to counter-
• Page 28 – CHECKPOINTS AFTER FINISHING A SERVICE; when the dishwasher stops.
• Page 29 – Asia