Samsung AC052MNADKH/EU - Installation Manual

Page 2 - English; Contents; Installation 3; Safety Information on Installation; Installation

2 English Contents Installation 3 Safety Information on Installation 3 Preparation 5 Step 1.1 Choosing the installation locationStep 1.2 Checking and preparing accessories and toolsStep 1.3 Drilling a hole through the wallStep 1.4 Performing the gas leak testStep 1.5 Insulating the refrigerant pipes...

Page 3 - General information

3 English Installation Carefully follow the precautions listed below because they are essential to guarantee the safety of both the air conditioner and the workers. • Always disconnect the air conditioner from the power supply before servicing it or accessing its internal components. • Verify that i...

Page 4 - breaker; CAUTION

4 English Installation trucks, scaffolding or any other means of elevation won’t be considered in-warranty and will be charged to end user. Power supply line, fuse, or circuit breaker • Always make sure that the power supply is compliant with current safety standards. Always install the air conditio...

Page 5 - Preparation; Overview of installation location requirements; Accessories

5 English Installation Preparation Step 1.1 Choosing the installation location Overview of installation location requirements CAUTION Step 1.2 Checking and preparing accessories and tools Accessories Accessories in the indoor unit package AC  MNADKH Installation plate (1)  026/035  (01 frame)...

Page 6 - Tools

6 English Installation AC  MNTDEH Installation plate (1)  100  Remote control (1) Remote control battery (2) User Manual (1) Installation Manual (1) Remote Control Holder (1) M4 x 16 Tapped Screws (2) Tools General tools • Vacuum pump (Backward flowing prevention) • Manifold gauge • Stud find...

Page 7 - Step 1.4 Performing leak test; Leak test; NOTE

7 English Installation A C B D F E 2 Drill the hole. CAUTION • Be sure to drill only one hole. • Make sure that the hole slants downwards so that the drain hose slants downwards to drain water well. Step 1.4 Performing leak test Leak test LEAK TEST WITH NITROGEN (before opening valves) In order to d...

Page 8 - Indoor Unit Installation

8 English Installation Step 2.1 Disassembling the cover panel (Only for AC  MNADKH) 1 Remove the cap screws, then the screws. 2 Unlock the side hooks ( , ), then centre hooks ( ).Then unlock the bottom hooks ( ) to pull out the cover panel. B B C A A 1 2 4 Step 2.2 Disassembling the installation ...

Page 11 - WARNING

11 English Installation have the same level of withstand voltage with the power cable. (Comply with the local regulations on extensions.) WARNING • In case of extending the electric wire, please DO NOT use a round-shaped pressing socket. – Incomplete wire connections can cause electric shock or a fi...

Page 15 - Step 2.11 Fixing the installation plate; When fixing the indoor unit on a wall; When fixing the indoor unit on a window frame

15 English Installation NOTE • Excessive torque may cause gas leakage. When extending the pipe with welding or brazing, ensure that nitrogen is used during the welding or brazing process. The joint must be accessible and serviceable. CAUTION • Tighten the flare nut at the specified torque. If the fl...

Page 16 - Step 2.13 Assembling the cover panel

16 English Installation Step 2.12 Fixing the indoor unit to the installation plate CAUTION • Make sure that the pipe bundle does not move when you install the indoor unit onto the installation plate. Step 2.13 Assembling the cover panel (Only for AC  MNADKH) 1 Lock the side hooks (D), then centre...

Page 17 - Setting an indoor unit address and installation option

17 English Installation • Set the indoor unit address and installation option with remote controller option. Set the each option separately since you cannot set the ADDRESS setting and indoor unit installation setting option at the same time. You need to set twice when setting indoor unit address an...

Page 22 - Setting the installation options in a batch

22 English Installation Setting an indoor unit address and installation option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 0 A 1 - - 3 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 1 - 1 - 1 B assign option codes except SEG 1, 7 which are page options. Setting the installation options in a batch 1 Make sure that the power is ...

Page 25 - LED Display; On Flickering X Off; Troubleshooting

25 English Installation Detection of errors  If an error occurs during the operation, an LED flickers and the operation is stopped except the LED.  If you re-operate the air conditioner, it operates normally at first, then detect an error again. LED Display on the receiver & display unit LED D...