Royal Sovereign RSL-2701 - Manual

Royal Sovereign RSL-2701

Royal Sovereign RSL-2701 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
Page: / 42

Table of Contents:

  • Page 2 – Exploded Drawings; Table of Content; Safety Precautions
  • Page 3 – Safety Precautions
  • Page 5 – Rollers Not Heating; The wire connector from the heater is disconnected; Before troubleshooting, be sure to; ) Test if the connector wire is; CAUSES; The wire connector from the heater is
  • Page 6 – The Wire-Temp Fuse is disconnected
  • Page 7 – Rollers Not Heating; The heater in the roller is defective.; Before trouble shooting, be sure to disassemble; MEASURES
  • Page 10 – Rollers Not Running; Before troubleshooting, be sure to disassemble; MICRO; MOTOR
  • Page 11 – Replace Motor with new one according to How to replace the Motor.; MAIN SWITCH
  • Page 13 – Poor Lamination Quality
  • Page 14 – ) Unfasten 4 screws holding the Right; cover and disassemble the Right cover.; ) Unfasten 4 screws holding the Sub-PCB
  • Page 15 – and disassemble the Left cover .; ) Disassemble both the Right cover and the Left cover.
  • Page 16 – white plastic supporters.; PCB SUPPORT
  • Page 17 – ) Unfasten 2 screws holding the heater and disassemble the wire.
  • Page 18 – and the heater enter the roller smoothly.
  • Page 19 – ) Disassemble the Right cover , the Left
  • Page 21 – Adjusting Front and Rear Roller; with different thickness of substrates.; Check above steps 2 through 4; with; Checking for over all tension; Pressure; Use Screwdriver; to adjust the roller pressure:; Figure B
  • Page 22 – SVC Parts List
  • Page 32 – Frame, Roller and Other View
  • Page 33 – Wire, Power core and Control PCB
  • Page 38 – Wire, Front Table and Safety Cover
Loading the manual

MODEL: RSL-2701

RSL-2701U

RSL-380

ROLL LAMINATOR SERVICE MANUAL

www.royalsovereign.com

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Exploded Drawings; Table of Content; Safety Precautions

3 ~ 3 4 ~ 10 4 ~ 6 6 ~ 7 8 ~ 9 9 ~ 10 11 ~ 11 12 ~ 18 12 ~ 12 13 ~ 13 13 ~ 14 14 ~ 14 15 ~ 15 15 ~ 16 16 ~ 17 17 ~ 18 19 ~ 19 20 ~ 23 24 ~ 34 35 ~ 38 4.Adjustments …………………………………………………………………………………… 3.8) Replacement of Motor……………………………………………………………………… 5. Parts List ………………………………………………………………………………………… 2...

Page 3 - Safety Precautions

3 1. Safety Precautions 3 Failure to comply any of the following safety procedures could result in serious injury. Please read the instructions carefully and keep for future reference. 1. Only a licensed electrician should install wiring and outlet for the laminator. 2. Ensure the unit is plugged in...

Page 5 - Rollers Not Heating; The wire connector from the heater is disconnected; Before troubleshooting, be sure to; ) Test if the connector wire is; CAUSES; The wire connector from the heater is

2.1 Rollers Not Heating 1. The wire connector from the heater is disconnected with MAIN PCB.(except RSL-380) 2. The Wire-Temp Fuse is disconnected. 3. The Main Fuse is defective.(except RSL-380) 4. The Bi-metal is defective. 5. The heater in the roller is defective. 6. Main PCB is defective. Before ...

Other Royal Sovereign Models