Royal Sovereign RSH-380SL - Manual

Page 2 - Table of Content

3 ~ 3 4 ~ 10 4 ~ 6 6 ~ 7 7 ~ 9 9 ~ 10 11 ~ 11 12 ~ 14 12 ~ 12 13 ~ 13 13 ~ 13 13 ~ 13 13 ~ 13 13 ~ 14 14 ~ 14 15 ~ 16 17 ~ 19 20 ~ 25 26 ~ 29 30 ~ 33 4.Adjustments …………………………………………………………………………………… 5. Parts List ………………………………………………………………………………………… 6.Exploded Drawings ……………………………………………………………………… 7.Wire...

Page 3 - Safety Precaution; Safety Precautions; Keep flammable and wet objects away from the machine .

Safety Precaution 1. Safety Precautions Failure to comply any of the following safety procedures could result in serious injury.Please read the instructions carefully and keep for future reference. 1. Only a licensed electrician should install wiring and outlet for the laminator. 2. Ensure the unit ...

Page 4 - Rollers Not Heating; a. Connect the upper and lower heating wires to the main PCB.

Note: While repairing: a. Make sure the power plug is unplugged from the power outlet. b. Open both side covers and rear cover. c. Be sure to follow the steps below in order. 2.1 Rollers Not Heating CAUSES: 1. Improper laminating mode. 2. Heating wire is not connected to the main PCB. 3. Blown (burn...

Page 5 - b. Physically examine the heater assembly for breakage.; Broken

2. Blown (burnt) wire fuse (T/Fuse). a. Replace the T/Fuse wire located on the left-hand side. 3. Defective Bi-Metal. a. Replace the Bi-Metal 4. Defective heater. a. Using the multi-meter, test the continuity of the heater. If it fails, replace the heater. b. Physically examine the heater assembly f...

Page 6 - Connector-Wire Sensor

5. Defective Main PCB. a. Replace the PCB Main. 2.2 Rollers Over Heating CAUSES 1. Heat sensor is reversed on the PCB Main. 2. Defective T/Fuse wire. 3. Defective heater. 4. Defective main PCB. MEASURES 1. Wires for lower and upper heat sensors are reversed on the main PCB. a. Reverse the heat senso...

Page 7 - Main Switch

4. Defective Main PCB. a. Replace the PCB Main. 2.3 Rollers Not Running CAUSES 1. No power to the unit. 2. The main switch is close. 3. Opened safety cover. 4. Film is jammed on the rollers. 5. Disconnected motor wire. 6. Defective main motor. 7. Defective main PCB. MEASURES 1. No power to the unit....

Page 8 - a. Check the motor wire connection with PCB.; Switch is engaged; Motor

4. Film is jammed on the rollers. a. Un-jam the film using a combination of the pressure lever and reverse button. 5. Disconnected motor wire. a. Check the motor wire connection with PCB. 6. Defective main motor. a. Replace the main motor. Switch is engaged Wire-motor Motor 6

Page 9 - a. Replace the main fuse located above the main power switch.; Main Fuse

7. Defective main PCB. a. Replace the main PCB. 2.4 No Main Power CAUSES 1. No electricity. 2. Blown main fuse. 3. Disconnected main power wires. 4. Defective transformer. MEASURES 1. No Electricity. a. Double check to insure that you have electricity from your outlet. b. Check the circuit breaker. ...

Page 10 - Transformer

4. Transformer is defective a. Replace the transformer. Problem: Straight wave lines across the output. Cause: Excessive front roller pressure. Measure: Loosen the front roller pressure. Problem: Concave waves in the lamination. Cause: Excessive rear (pulling) roller pressure. Measure: Loosen the re...

Page 11 - Replacing the Main PCB; c. Replace the board with new PCB and connect all the wires.; Figure 1

Note: While replacing parts: a. Make sure the power plug is unplugged from the power outlet. b. Open both side covers and rear cover. 3.1 Replacing the Right Cover. a. Take out the pressure lever (Figure 1) and four cover screws using Phillips screw driver (Figure 2). b. Pull out the male control pa...

Page 12 - Replacing the Heaters; a. Disassemble Right and Left Covers (Refer to “; Replacing Right Cover; ” and “; Replacing Left Cover; c. Take out the broken heater. Figure 10; Replacing the Cross Cutter; d. Assemble the Cutter by reversing the above steps.; Figure8

3.4 Replacing the Heaters Note: Cotton or surgical gloves are recommended while handling the heater assembly. a. Disassemble Right and Left Covers (Refer to “ Replacing Right Cover ” and “ Replacing Left Cover ”). b. Take out the heater brackets on each side by loosening screws (Figure 8, 9). c. Tak...

Page 13 - Use Screwdriver

.2 Adjusting front and rear rollers Pressure • Use Screwdriver to adjust the roller pressure: C.W – Increase pressure. C.C.W – Decrease pressure. 1.Using Push-Pull Scale , measure 3 spots as shown on Figure B &C: Front roller should be 5~6 and back rollers should be 6~8. 2.Checking for over all ...

Royal Sovereign RSH-380SL - Manual

Table of Contents:

Summary

Other Royal Sovereign Models