Robertshaw 9560 - Manual
Robertshaw 9560 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – IMPORTANT SAFETY INFORMATION; Step 1: Replacing Existing Thermostat; Old Terminal; Figure 1
- Page 3 – Remove existing thermostat base from wall.; Recycling Thermostat; NOTE: FOR NEW INSTALLATIONS, MOUNT THERMOSTAT ON; Turn power off to the heating and cooling systems.; Figure 2; TM
- Page 4 – will feed through opening (Figure 4) on base of thermostat.; NOTE: ENCLOSED PLASTIC ANCHORS DO NOT REQUIRE A; face other than drywall.; NOTE: THE THERMOSTAT WILL MOUNT HORIZONTALLY; Figure 3; Mounting Holes; Figure 4
- Page 5 – Wiring Diagrams; Make sure wire connections are secure.
- Page 6 – Figure 6; TERM
- Page 7 – Turn on power to system. Test thermostat as described in the; Step 3: Testing the Thermostat; CAUTION: DO NOT SWITCH SYSTEM TO COOL IF THE TEMPERATURE IS; button until the temperature setting; NOTE: ONCE THE THERMOSTAT TURNS OFF WHEN IN THE COOL MODE, A; Figure 7
- Page 9 – System; Temperature Differential and Deadband; NOTE: IF THE TEMPERATURE LIMITING JUMPER J3 IS CUT; Figure 8
- Page 10 – DIFFERENTIAL 1; AUTOCHANGE DEADBAND; LED Indicators
- Page 11 – Symptom; If problems with thermostat cannot be resolved, call:; RESET Switch
- Page 12 – Two Year Limited Warranty; warrants to the original contractor; Climate Controls Americas; Warranty Claims Department
Application
The Robertshaw 9560 is a multi-stage auto changeover thermostat
designed to control 24 VAC heat pump systems up to 2 stage heat and 2
stage cool. The 9560 requires the use of a common wire.
Features
• Multi-stage control
• Auto changeover [deadband adjustable from 2°F to 8°F (1.0°C - 4.5°C)]
• Large back lit display
• Adjustable 1
ST
and 2
ND
stage temperature differential
• Compressor short cycle protection
• Adjustable fan delay on cooling
• LED indication of system status
• Zone system compatible as a master thermostat
• Battery-free EEPROM memory retention
• Optional temperature limiting settings
• Fahrenheit/Celsius display option
• Adjustable from 45°F to 90°F (7°C - 32°C)
• Quick wire terminal block
1
D E L U X E
N O N - P R O G R A M M A B L E
T H E R M O S TAT
9560
H E AT P U M P
H
®
NeW
2 Heat / 2 Cool
with Auto Changeover
User's Manual
Quick Start
Installation
W
A R R A N T Y
2
TW
O YEAR
110-1033
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
IMPORTANT SAFETY INFORMATION WARNING: • Always turn off power at the main power source by unscrewing fuse or switching circuit breaker to the off position before installing,removing, cleaning, or servicing thermostat. • Read all the information in this manual before installing or program- ming this ...
• If you have any questions about cross referencing the old terminal to the new label, reference your equipment installation manual, alicensed contractor, or call Robertshaw Technical Support at (800) 445-8299. 4. Remove existing thermostat base from wall. Recycling Thermostat If this thermostat is ...
4. Remove the cover using a coin or screwdriver (Figure 3). Set aside. 5. Place thermostat against the wall at desired location. Make sure wires will feed through opening (Figure 4) on base of thermostat. 6. Mark placement of mounting holes (Figure 4). Set base aside. 7. If mounting on drywall, tap ...
