Robertshaw 110-10978 - Manual
Robertshaw 110-10978 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Do not connect ground to any terminal in this unit.; Recycling Thermostat; Wiring Table
- Page 3 – Figure 1; Installing Item 8600 Thermostat; Figure 2
- Page 4 – To Test Thermostat; Figure 3
- Page 5 – Wiring Diagrams
- Page 7 – CAUTION: DO NOT SWITCH SYSTEM TO COOL OR LEAVE IN COOL MODE; NOTE: ONCE THE THERMOSTAT TURNS OFF WHEN IN THE COOL MODE,; button until the temperature; NOTE: If HP is selected, the heat will not come on until the 5 minute; AUTO-ON switch into the ON
- Page 8 – Programming Guide; AM; PROGRAMMING YOUR THERMOSTAT
- Page 9 – CUSTOMIZING YOUR THERMOSTAT
- Page 11 – Check Filter Reset; CHECK FILTER; Backlit Display
- Page 12 – Troubleshooting; Symptom; If problems with thermostat cannot be resolved, call:; For after hours service, a 24-hour automated help line is available.
- Page 13 – Two Year Limited Warranty; warrants to the original contractor installer,
- Page 14 – NOTES
1
Application
The Robertshaw 8600 is a single-stage thermostat designed to control
24 VAC gas or electric heating and cooling systems or single-stage
heat pumps.
Features
• Large backlit display.
• Four preprogrammed E
NERGY
S
TAR
®
setpoints for each day of
the week.
• Two AA ENERGIZER brand batteries retain time of day settings even
during power outages.
• Low battery indicator.
• Fahrenheit/Celsius display option.
• Programmable from 45°F (4°C) to 90°F (32°C).
• Accuracy within ± 1 degree.
• Adjustable temperature differential: 1-3 °F (1-1.5°C).
• Separate heating and cooling programs.
• Low temperature freeze protection. While in heat mode, the
thermostat will mechanically turn on the heat if the temperature
drops to 40°F (4°C) – even if the batteries are drained or missing.
110-1097B
5 - 2 Day Programmable
1 Heat / 1 Cool
User’s Manual
Quick Start
Installation and
Programming
W
A R R A N T Y
2
TW
O YEAR
D I G I TA L
P R O G R A M M A B L E
T H E R M O S TAT
8600
E L E C T R I C
E
G A S
G
O I L
O
®
NeW
H E AT P U M P
H
As an E
NERGY
S
TAR
®
partner, Invensys Controls Americas has determined
that this thermostat product meets the E
NERGY
S
TAR
®
guidelines for
energy efficiency.
110-1097B 3/8/05 10:39 AM Page 1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
WARNING: • Always turn off power at the main power source by unscrewingfuse or switching circuit breaker to the off position before installing,removing, cleaning, or servicing thermostat. • Read all of the information in this manual before installing or programming this thermostat. • DO NOT CONNECT ...
WARNING: In heat pump applications, do not connect anything to the W1terminal. When switched to HP mode, W1 is connected internallyto Y1 on the thermostat. 1. Turn off power to heating and cooling system. 2. Remove cover of old thermostat to expose wires. Do not disconnect wires. (See Figure 1) 3. L...
6. Mark placement of mounting holes (see Figure 3). Set base aside. 7. Drill the marked holes using a 3/16” (5mm) drill bit. NOTE: Enclosed plastic anchors do not require a drilled hole for drywall. 8. Tap plastic anchors into the wall. 9. Align base with plastic anchors and feed wires through openi...
