Rinnai FS35ETRBL/US - Manual

7 TECHNICAL SPECIFICATIONS COMPARTMENTS, BURNERS ANDCIRCULATING AIR PASSAGEWAYSOF THE APPLIANCE ARE KEPTCLEAN. 35 The glass window shall be replaced as one piece as supplied by themanufacturer. See log and glassinstallation on page 15. 36 Do not substitute glass, glowing embers or logs. Use only gla...

9 For your convenience the controls on your new Flame Fire are situated under the cover on thetop right-hand side of the fire and are accessed by simply lifting the lid. All necessaryadjustments to the operation of your fire can be made with these controls. OPERATION CONTROL PANEL LAYOUT • TURNING O...

10 deactivate the LOCK press and hold thebutton for 3 seconds until the indicatorgoes off. During normal operation the LOCK may beactivated and all controls, other than theOFF switch, will be locked. Deactivatingthe LOCK releases the controls. If the LOCK is activated while the unit isturned OFF, th...

11 proceed to TIMER 2 - which isprogrammed in the same way - or threetimes to return to the clock display. Thismust be done within 1 minute of setting thetime to lock it into the memory. The digital display will show the currenttime. A small indicator on the digital displaywill flash to show that th...

13 1. Flue connection and proper venting 2. Warm air distribution. 3. Adequate air supply. 4. The heater must not be installed where curtains or other combustible materialscould come into contact with it. In somecases, curtains may need restraining. See below for minimum clearancesrequired. LOCATION...

14 • RUN GAS SUPPLY For pipe sizing, refer to your local gasinstallation codes. • PURGE SUPPLY OF AIR AND DEBRIS All foreign materials such as filings mustbe purged from the gas supply, as they maycause the gas valve to malfunction. A means to measure the gas pressureimmediately upstream of the supp...

15 The logset is packed inside the unit andthe packaging must be removed prior toinstalling the logset in its correct position. • Open both side panels. • Remove fasteners on both sides of the top glass retainer. • Lift retainer away from unit. • Loosen screws on bottom glass retainer. • Carefully l...

16 • TESTING PROCEDURE Turn gas supply on and plug the unit intothe power supply. (Caution 115V) • TO CHECK BURNER PRESSURE • Refer to rating plate. • Remove the wiring cover panel. • Remove test point plug and attach manometer to test point. The test point is on the bottom front face of the gas val...

17 IMPORTANT MAINTENANCE INSTRUCTIONS ANNUAL INSPECTION The unit should be inspected at least oncea year by a qualified service technicianincluding inspection of the flue system. The appliance area must be kept clear andfree from combustible materials, gasolineand other flammable vapors and liquids....

18 1 3 3 2 1 1 3 4 2 2 The heater should be servicedannually only by an authorised person. • GLASS REPLACEMENT AND CLEANING. (May be performed by the owner) It is best to handle the glass with cleangloves to avoid smearing the glass withfinger prints which might show afterreplacement. Refer diagram ...

20 NOTE: If you have any other faults or problems, please refer to your Installer or local qualified service agency TROUBLE SHOOTING WIRING DIAGRAM-LADDER SYMPT OM CAUSE SOLUT ION No power present Ensure power cord is plugged in and turned on No gas present Ensure gas supply is turned on power cut R...

21 Error code Probable cause Comments 11 Ignition failure Check gas is turned on.Service call if repeated 12 Flame failure Check gas is turned on.Service call if repeated 14 Overheat Service call 16 Room overheat Lower rom temperaure to less than 104°F 31 Service call 32 Service call 33 Overheat tem...

24 SPARE PARTS LIST ITEM NO. QTY. PART NO. 1 1 7992-1 FLUE SPIGOT ASSY FS NAT USA 2 1 7074 HEAT EXCHANGER FRONT ASSY 3+3H 3 1 7075 HEAT EXCHANGER REAR ASSY 3H 4 6 6624 BURNER EXCHANGER TRANSFER TUBE 5 2 6625 BURNER HEAT EXCHANGER BRACKET 6 1 7028-5 FLUE SPIGOT DRAUGHT DIVERTER 7 1 7926 COMB CHAMB AS...

27 1. Was a fireplace inspection carried out? (i.e. clearances, combustibles etc.) 2. Was a manufactured flue system installed? 3. Has specified gas pressure been set? 4. Are decorative logs located correctly on pins? 5. Have ember granules been placed and free of dust and powder? 6.Has the applianc...