Rinnai FM10NA - User Manual

Page 2 - years of comfort and enjoyment from your appliance.; BEFORE USING THIS APPLIANCE; • Local Regulations and Municipal Building Codes

Rinnai 2 HW_GI_FM10 OIM Congratulations on the purchase of your Rinnai Gas Instantaneous Water Heater. We trust you will have many years of comfort and enjoyment from your appliance. IMPORTANT BEFORE USING THIS APPLIANCE Before proceeding with the operation or installation read this manual thoroughl...

Page 3 - OPERATION TABLE OF CONTENTS; Warnings & Important Information; Features and Benefits

Rinnai 3 HW_GI_FM10 OIM OPERATION TABLE OF CONTENTS Warnings & Important Information 4 Before Using This Appliance .............................................................................................................................................. 4 Regulatory Information ................

Page 4 - REGULATORY INFORMATION; WARNING ABOUT HOT WATER; WARNINGS & IMPORTANT INFORMATION

Rinnai 4 HW_GI_FM10 OIM WARNING BEFORE USING THIS APPLIANCE Before proceeding with the operation or installation read this manual thoroughly and gain a full understanding of the appliance, to ensure safe and correct use.Always comply with the following precautions to avoid dangerous situations and t...

Page 5 - MANDATORY INSPECTION PRIOR TO INSTALLATION; The range of Rinnai gas instantaneous water heaters

Rinnai 5 HW_GI_FM10 OIM IMPORTANT MANDATORY INSPECTION PRIOR TO INSTALLATION Immediately report any damage or discrepancies to the Supplier of the appliance. This appliance was inspected and tested at the time of manufacture and packaging, and released for transportation without known damage. Upon r...

Page 6 - The appliance is compact, saving both wall and floor space.; FEATURES AND BENEFITS

Rinnai 6 HW_GI_FM10 OIM FEATURES & BENEFITS Congratulations on purchasing the Rinnai Gas Instantaneous water heater. • The appliance is compact, saving both wall and floor space. • The burner lights automatically when the hot water tap is opened, and goes out when the tap is closed. IGNITION IS ...

Page 7 - TO OPERATE; HOT; Battery for electronic ignition and control; OPERATION

Rinnai 7 HW_GI_FM10 OIM TO OPERATE The opening of any hot water tap will automatically start the appliance. Once water is flowing through the appliance the burner will be ignited by electronic ignition via the electronic ignition and control module. When the hot water tap is closed and water flow th...

Page 8 - WATER FLOW AND TEMPERATURE ADJUSTMENT; This is not supplied with the water heater.

Rinnai 8 HW_GI_FM10 OIM WATER FLOW AND TEMPERATURE ADJUSTMENT Water fixtures with a rated water flow rate of 7.5 litres per minute or higher are recommended.A water flow adjustment lever is fitted to adjust the maximum water flow from the appliance. Such adjustment may be useful to compensate for se...

Page 9 - FAULT FINDING; TROUBLE SHOOTING

Rinnai 9 HW_GI_FM10 OIM FAULT FINDING Problem Fault Solution Burner does not ignite, or is difficult to ignite No gas supply Check gas is turned on at water heater and gas meter or cylinder Low battery power Replace battery Other Service Call Pilot lights but no main burner Low water pressure Check ...

Page 10 - This page is intentionally blank

Rinnai 10 HW_GI_FM10 OIM This page is intentionally blank

Page 11 - INSTALLATION TABLE OF CONTENTS

Rinnai 11 HW_GI_FM10 OIM Operation Table of Contents 3 General Installation Information 12 Regulations ........................................................................................................................................................................ 12Applicable Models ...........

Page 12 - MUST; GENERAL INSTALLATION INFORMATION

Rinnai 12 HW_GI_FM10 OIM NOTE Installation, service and removal MUST BE by an appropriately licensed tradesperson ONLY . It is the installer’s responsibility to ensure all current AS/NZS 5601 requirements are met. Remove transit protection. Check for damage, if any is found DO NOT install and contac...

Page 13 - WATER SUPPLY; lower pressures but will not achieve the rated flow.; HOT WATER DELIVERY TEMPERATURE; incoming cold water temperature and high water flow; APPLIANCE MOUNTING REQUIREMENTS; heat shield is fitted.; heat shield is

Rinnai 13 HW_GI_FM10 OIM WATER SUPPLY See "Table 1. Appliance Specifications" on page 18, for applicable water pressures. Approved pressure limiting valves may be required if the 'Maximum' rated water supply pressures in Table 1 are exceeded. To achieve the rated flow, the 'Minimum' water su...

Page 14 - APPLIANCE MOUNTING METHOD; inner face of the fixing and the wall. This gap is; SERVICE CONNECTION POINTS; appliance connection / fitting dimensions.; An approved full flow isolation valve and disconnection; MUST NOT; be fitted directly; CL; Propane Gas

Rinnai 14 HW_GI_FM10 OIM APPLIANCE MOUNTING METHOD 1. After determining the desired location for the water heater, use the dimensions in the drawing right to measure and mark off the positions of the 3 appliance mounting points A and the 4 heat shield mounting points B . 2. Install 3 suitable screws...

Page 15 - APPLIANCE FLUE TERMINAL; FLUEING

Rinnai 15 HW_GI_FM10 OIM APPLIANCE FLUE TERMINAL R e f . e f . M i n c l e a r a n c e s m m Natural draught a B e l o w e a v e s , b a l c o n i e s a n d o t h e r p r o j e c t i o n s : F o r a p p l i a n c e s u p t o 5 0 M J / h i n p u t 3 0 0 F o r a p p l i a n c e s o v e r 5 0 M J / h i...

Page 16 - TESTING; If the sparker activates but the pilot and main; Test Point Screw; COMMISSIONING

Rinnai 16 HW_GI_FM10 OIM TESTING 1. Before final connection of the water heater purge gas, hot water and cold water supply lines. Swarf in either the gas or water supplies may cause damage or malfunction which is not covered by warranty. 2. See Table 1 for connection size, water and gas pressure spe...

Page 17 - COMMISSIONING CHECK LIST; from operating correctly.; INSTALLATION RECORD; Installation Company Name:; System Details; Installation Address:

Rinnai 17 HW_GI_FM10 OIM COMMISSIONING CHECK LIST A commissioning check list is provided on the appliance front cover to enable the installer to step through the correct commissioning procedure when installing a Rinnai water heater. The check list can also assist the installer to identify potential ...

Page 18 - Appliance Specifications; Male; SPECIFICATIONS

Rinnai 18 HW_GI_FM10 OIM Table 1. Appliance Specifications Model Water Supply kPa Weight kg Fittings Minimum Inlet Water Pressure For 10L/min. Minimum Inlet Water Pressure For Operation Maximum Inlet Water Pressure Hot & Cold Water Natural Gas Propane Gas FM10 120 40 1000 14 R 1/2” BSP Male R 1/...

Page 19 - Figure 4. Dimensions; Approximately; APPLIANCE DIMENSIONS

Rinnai 19 HW_GI_FM10 OIM Figure 4. Dimensions Approximately 175 to base of fittings 61 51 575 170 838 425 48 380 205 201219 380 120 120 120 120 70 70 70 51 Location of upper rear mounting holes Location of lower rear mounting hole APPLIANCE DIMENSIONS

Page 20 - Figure 5. Dimensions; WIRING DIAGRAM

Rinnai 20 HW_GI_FM10 OIM Solenoid Valve 1 Solenoid Valve 2 High Voltage Lead (Ignition) Flame Rod Temperature Overheat Switch (Self-resetting) Modulation Motor Thermistor (Heated water outlet temperature) Micro-switch SV1 SV2 HV FR TTB M NTC SW MAIN MICROPROCESSOR TEMPERATURE CONTROL MICROPROCESSOR ...

Page 21 - NOTES

Page 24 - Rinnai Australia Pty Ltd; National Help Line

Rinnai Australia Pty Ltd ABN 74 005 138 769 | AU24752 100 Atlantic Drive, Keysborough, Victoria 3173P.O. Box 460, Braeside, Victoria 3195Tel: (03) 9271 6625Fax: (03) 9271 6622 National Help Line Tel: 1300 555 545* Fax: 1300 555 655 Monday to Friday, 8.00 am to 5.00 pm EST. After Hours Hot Water Serv...

Rinnai FM10NA - User Manual

Table of Contents:

Summary

Other Rinnai Hot Water Systems Models