Regency 946-523/P - Manual
Regency 946-523/P – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – P33 Gas Fireplace; Approved Venting Systems; * The unit must be raised a minimum of 1” above the; LP4 Gas Fireplace, the burner ori; Gas Fireplaces
- Page 3 – Framing and Finishing; fl; Combustible Mantels; Drywall; Side View; Mantel Leg Clearances; WARNING; Clearance Requirements
- Page 4 – Dimension; Installation of this; Due to ongoing product development, product appearance and speci
- Page 5 – Horizontal Terminations Only; Important; Snorkel Terminations; Snorkel Terminations:; cations Book
- Page 6 – Rigid Pipe System; ertical; Alternate Horizontal
- Page 7 – Two 45° elbows = One 90° elbow; Vertical Venting with Two (2) 90° Elbows; Option; Two 45° elbows = One 90° elbow; Option; Two 45° elbows = One 90° elbow; Option
- Page 8 – using one 45° and one; Maintain clearances to combustibles.; refer to Exterior; * Unit must be raised by 1” when using
- Page 10 – Vertical termination with co-linear; The appliance must not be connected to a chimney; Please refer to Exterior Vent Terminations for
P33 Zero Clearance Direct Vent Gas Fireplace
Model
P33-NG4
P33-LP4
Fuel Type
Natural Gas
Propane
Minimum Supply Pressure
5” W.C. (1.25 kPa)
12” W.C. (3.00 kPa)
Manifold Pressure - High
3.8” W.C. (0.95 kPa)
11” W.C. (2.74 kPa)
Manifold Pressure - Low
1.1” W.C. (0.27 kPa)
3.3” W.C. (0.82 kPa)
Ori
fi
ce Size
#44 DMS - 0-2000ft
#45 DMS - 2000-4500ft
#54 DMS
Minimum Input
Altitude 0-2000 ft. (0-610m)
12,500 BTU/h
(3.66 kW)
10,500 BTU/h
(3.07 kW)
Minimum Input
Altitude 2000-4500 ft. (610-1372m)
10,500 BTU/h
(3.07 kW)
Maximum Input
Altitude 0-2000 ft. (0-610m)
22,500 BTU/h
(6.59 kW)
21,500 BTU/h
(6.30 kW)
Maximum Input
Altitude 2000-4500 ft. (610-1372m)
21,000 BTU/h
(6.15 kW)
Vent Sizing
4” Inner / 6 5/8” Outer
4” Inner / 6 5/8” Outer
A
B
A
D
C
F
E
Unit Dimensions
Description
P33
A
Front Face Width
33” (838mm)
B
Rear Firebox Width
23” (584mm)
C
Front Face Height
29” (737mm)
D
Height w/ Standoff
31 1/2” (800mm)
E
Unit Depth
12-3/4” (324mm)
F
Firebox Height
28 1/2” (724mm)
Framing Dimensions Description
P33
G
Framing Width
33-1/4” (845mm)
H
***
Framing Height
***
31-3/4” (806mm)
***
I
Framing
Depth
Vertical
19 1/2” (495mm)
Vertical Rise
16 1/2” (419mm)
Rigid
12-3/4”
(324mm)
Flex
Horizontal
J
Corner Wall Length
37 1/2” (953mm)
K
Corner Facing Wall Width
53-1/4” (1353mm)
L
Framed Chase Ceiling
36” (914mm)
Rigid
32” (813mm)
Flex
M
Vent Centerline Height
30” (762mm)
Rigid
26” (660mm)
Flex
G
H
I
K
J
L
Q
O P
N
M
10" (254mm)
dia. Hole through
wall Vent.
Opening for gas
connection
Top Header
Drywall
(or other
facing)
R
Dimension
Description
P33
N
Gas Connection Height
1 1/2” (38mm)
O
Gas Connection Inset
4” (102mm)
P
Gas Connection Width
3” (76mm)
Q
Minimum Framing Depth
16 1/2” (419mm)
Rigid /
12-3/4” (324mm)
Flex
R
Maximum Framing Depth
(including wall thickness)
40 1/2” (419mm)
Rigid /
36-3/4” (324mm)
Flex
P33 Gas Fireplace
Approved Venting Systems
Flex Vent Systems:
FPI AstroCap™ Flex Vent
Rigid Pipe Vent Systems:
Simpson Direct Vent Pro®
American Metal Products® Amerivent Direct
Security Secure Vent®
Selkirk Direct-Temp™
Metal-Fab® Sure Seal
***
Important: Framing height requires consideration of the hearth
depth. Dimension H = H + the thickness of installed hearth.
Please refer to Exterior Vent Terminations for
additional guidelines on vent locations.
P33 WITH THE FLUSH OR BAY FRONT
28
August 2008 Product Speci
fi
cations Book
Gas Fir
eplaces
Gas Fireplaces
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Model P33-NG4 w/ Contemporary Faceplate P33-LP4 w/ Contemporary Faceplate Fuel Type Natural Gas Propane Minimum Supply Pressure 5” W.C. (1.25 kPa) 12” W.C. (3.00 kPa) Manifold Pressure - High 3.8” W.C. (0.95 kPa) 11” W.C. (2.74 kPa) Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 3.3” W.C. (0.82 kPa) O...
Framing and Finishing 1) Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the fi nished surface to be fl ush with the front of the unit. Total facing thickness can vary from 1/2” (13mm) to 1-¼” (32mm) thick. 2) Frame in the enclosure for the unit with frami...
P33 Gas Fireplace Combustible Mantels with Contemporary Faceplate Because of the extreme heat this fi replace emits, the mantel clearances are critical. Combustible mantel clearances from top of the louvers are shown in the diagram below. Mantel may be installed anywhere in the shaded area or higher...
