Razor E225S - Manual - manualsarea.com

Page 2 - SAFETY WARNINGS

WARNING: Riding the E100, E200 or E300 scooter can be a hazardous activity. Certain conditions may cause the equipment to fail without fault of the manufacturer. Like other electric vehicles, the scooter can and is intended to move, and it is therefore possible to lose control, fall off and/or get i...

Page 3 - Estimated Assembly and Set-Up Time; BEFORE YOU BEGIN; DO NOT USE NON-RAZOR; Required Tools; or call toll-free at

Charger Charger Plug Charger Port Remove contents from box. Remove the foam separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the scooter was 95 percen...

Page 4 - Be sure to properly align the

3 ASSEMBLY AND SET-UP ❑ Attaching the Handlebars WARNING: Failure to properly tighten the wedge may allow the handlebars to dislodge while riding and may cause you to lose control and fall. When correctly tightened, the handlebars will not rotate out of alignment with the front wheel under normal ci...

Page 5 - Testing the Brakes –; Adjusting the Brakes; REPAIR AND MAINTENANCE

❑ Adjusting the Handlebar Height ❑ Riding Your Scooter Testing the Brakes – To use the brakes, squeeze the front and back brake levers to increase the pressure on the brake. The brake lever is ﬁ tted with a cable adjuster to compensate for cable stretch and/or to ﬁ ne-tune the lever movement to brak...

Page 6 - Infl ating the Tires

5 REPAIR AND MAINTENANCE 1 Use the special valve extender/adapter supplied. The valve adapter is located in the bag with the owners manual supplied at the time of purchase. 2 Align the access hole in the drive sprocket with the tire valve. Thread the adapter completely onto the valve and attach the ...

Page 7 - Adjusting the Chain

6 REPAIR AND MAINTENANCE ❑ Adjusting the Chain Tools required: 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches. 1 Using two 17mm wrenches, loosen the rear axle bolts by turning the wrenches counter clockwise. 2 Using two 8mm wrenches, loosen the brake housing anchor which is located in ...

Page 8 - Chain and Rear Tire Replacement

7 REPAIR AND MAINTENANCE ❑ Chain and Rear Tire Replacement Tools required: Phillips screwdriver, 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches. 1 With a Phillips screwdriver, loosen the two screws and remove the chain guard. 2 With a 10mm wrench, loosen the brake cable anchor and disc...

Page 10 - Front Tire Replacement

9 REPAIR AND MAINTENANCE 1 (E100 Only) Loosen the brake pad bolt and remove one brake pad. ❑ Front Tire Replacement Tools required: 10mm wrench, two (2) 17mm wrenches and a ﬂ athead screwdriver. 2 Using two 17mm wrenches, loosen the front axle bolts by turning the wrenches counter clockwise. 3 Remov...

Page 12 - TROUBLESHOOTING GUIDE

11 TROUBLESHOOTING GUIDE Scooter does not run Scooter was running but suddenly stopped Short run time (less than 30 minutes per charge) Scooter runs sluggishly Problem Possible Cause Solution Undercharged battery Charger is not working Loose wires or connectors E100 only only - Scooter must be trave...

Page 22 - Razor Limited Warranty; WARRANTY; Loose Parts; SAFETY REMINDERS; DO NOT RETURN TO STORE; Do not use this vehicle for the fi rst time until you have infl ated the

Tire Inﬂ ation Periodically inspect the tires for excess wear, and regularly check the tire pressure and re- inﬂ ate as necessary. If you get a ﬂ at tire, the inner tube can be patched or a new tube can be purchased from Razor or an authorized repair center. Safety Gear Always wear proper protective...

Razor E225S - Manual

Table of Contents:

Summary

Other Razor Models