Raypak 185A - Manual
Raypak 185A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – REMOVE THESE
- Page 3 – REMOVE MOUNTING SCREWS
- Page 4 – UNPLUG
- Page 5 – Make sure the power and gas are off.; not; UNPLUG ALL WIRES
- Page 6 – PROPANE HEATERS ONLY:; PROPANE
- Page 7 – DO NOT; break tab See; DO; break
- Page 8 – BROKEN TAB
- Page 9 – LAY BOARD; REMOVE BACKING
- Page 10 – LAY BEZEL
- Page 12 – CLEAR PLASTIC STRIP; OR; SIDE VIEW; SHIELD
- Page 13 – INSTALLING PILOT HI TENSION WIRE EXTENSION SIZES 335A TO 407A:; to new; side ‘A’; to existing pilot wire
RAYPAK REPLACEMENT INSTRUCTIONS
IMPORTANT NOTICE
These instructions are intended primarily for use by qualified personnel specifically trained and experienced in the installation of this
type of heating equipment and related system components. Installation and service personnel may be required to be licensed in
some states. Persons not qualified shall not attempt to install this equipment nor attempt repairs according to these instructions.
P.C. BOARD, TEMPERATURE CONTROL & SENSOR (KIT #010253F) FOR ALL
DIGITAL GAS POOL HEATERS (SEE “SCOPE” FOR APPLICABLE MODELS)
DANGER - SHOCK HAZARD
Make sure electrical power to the heater is disconnected to avoid potential serious injury or damage to components.
SCOPE:
This version of the temperature control board has the capability of an integrated ignition module plus 3-wire temperature sensor.
The kit includes a gasket and a plastic shield that is mounted to the back side of the control panel to eliminate moisture
accumulation on the LCD display. It is a direct replacement for the following models: 185A, 185B, 206A, 207A, 265A, 265B, 266A,
267A, 335A, 335B, 336A, 337A, 405A, 405B, 406A, 407A.
Page
1
DANGER - PROPANE HAZARD
Make sure to determine if unit is propane and see special instructions on page 6.
P/N 241169 Rev.-3
MODELS
206A, 207A, 266A, 267A,
336A, 337A, 406A, 407A
PRODUCED OCT. 2004-
THROUGH CURRENT
SERIAL # 0410 - CURRENT
2151 Eastman Ave., Oxnard, CA 93030 805-278-5300 Fax 800-777-7026
www.raypak.com
Technical support is available M-F, 5:30 AM to 5:00 PM PST, at 800-947-2975 or 800-627-2975
MODELS
185B, 265B, 335B, 405B
PRODUCED NOV. 2003
THROUGH OCT. 2004
SERIAL # 0310 TO # 0410
MODELS
185A, 265A, 335A, 405A
PRODUCED NOV. 1998
THROUGH OCT. 2003
SERIAL # 9811 TO # 0310
(1) Instructions
(2) Screws #10 X 1/2"
(6) Screws #8 X 1/2"
(4) Screws #6 X 3/8"
(1) Hi tension wire extension
(1) Remote wire harness
(1) LCD Gasket
(6) Plastic #8 washer
(1) Temperature sensor
(2) Brackets
(1) PC board plastic shield
(1) P.C. control board
This kit includes
Th
e n
ew
sty
le
bo
ar
d
is
lar
ge
r
th
an
th
e o
ld
sty
le
bo
ar
d
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
r r Fig. 1 REMOVE THESE SCREWS Fig. 2 Page 2 2151 Eastman Ave., Oxnard, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.com Technical support is available M-F, 5:30 AM to 5:00 PM PST, at 800-947-2975 or 800-627-2975 REMOVE THESE SCREWS ACCESSING THE BOARD - MODELS 206A, 207A, 266A, 267A, 336A, 337...
REMOVING THE CIRCUIT BOARD - MODELS 185A/B, 265A/B, 335A/B, 405A/B: Make sure the power and gas are off.1. Unplug all connectors from old circuit board. Fig. 7 . 2. Unplug keypad ribbon from old circuit board.3. Remove four screws as shown in Fig. 8 . 4. Remove old circuit board. Fig. 7 2.2 UNPLUG A...
2151 Eastman Ave., Oxnard, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.com Technical support is available M-F, 5:30 AM to 5:00 PM PST, at 800-947-2975 or 800-627-2975 Page 4 UNPLUG ALL CONNECTORS REMOVE MOUNTING SCREWS Fig. 9 Fig. 10 REMOVING THE CIRCUIT BOARD - MODELS 206A, 207A, 266A, 267A, ...
