RadioShack FC-241 - Manual
RadioShack FC-241 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Dial Solutions; Configuring a Router as a TFTP Server; Note; Performing Prerequisite Tasks; ping
- Page 3 – Caution; Configuring the Server; Internetwork Troubleshooting Guide; Command
- Page 4 – Configuring the Client Router; no boot system; all
- Page 5 – filename address
- Page 6 – Configures the router as a RARP server.
- Page 7 – Router A has the following configuration:; Specifying Asynchronous Interface Extended BOOTP Requests; Shows parameters for BOOTP requests.
- Page 8 – Configuring a Router to Use rsh and rcp; Disabling DNS Reverse Lookup for RCMD
- Page 9 – Configuring a Router to Use rsh; without; Maintaining rsh Security; no ip rcmd rsh-enable
- Page 10 – Executing Commands Remotely Using rsh; username
- Page 11 – Configuring a Router to Use rcp; Configuring the Router to Accept rcp Requests from Remote Users; no ip rcmd rcp-enable; Enable the software to support incoming rcp requests.
- Page 12 – Configuring the Remote to Send rcp Requests; ip rcmd remote-username; boot
- Page 13 – Configuring a Router to Use FTP Connections; FTP Configuration Task List
FC-241
Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.1
First Published: July 14, 2000; Last Updated: Oct. 1, 2002
Configuring Additional File Transfer Functions
This chapter describes how to configure a router as a server, change MOP parameters, configure the
router to forward extended BOOTP requests over asynchronous interfaces, and configure rcp, rsh, and
FTP.
For a complete description of the file transfer function commands mentioned in this chapter, refer to the
“Additional File Transfer Functions Commands” chapter in the
Configuration Fundamentals Command
Reference
. To locate documentation of other commands that appear in this chapter, use the command
reference master index or search online.
Additional Functions Task List
To configure additional file transfer functions, perform any of the tasks in the following sections:
•
Configuring a Router as a Server
•
Specifying Asynchronous Interface Extended BOOTP Requests
•
Configuring a Router to Use rsh and rcp
•
Configuring a Router to Use FTP Connections
Configuring a Router as a Server
It is too costly and inefficient to have a machine which only acts as server on every network segment.
However, when you do not have a server on every segment, your network operations can incur enormous
time delays across network segments. You can configure a router to serve as a RARP or TFTP server to
reduce costs and time delays in your network while allowing you to use your router for its regular
functions.
Typically, a router that is configured as a server provides other routers with operating system images
from its Flash memory. You can also configure the router to respond to other types of service requests,
such as Reverse Address Resolution Protocol (RARP) requests.
To configure the router as a server, perform any of the tasks in the following sections. The tasks are not
mutually exclusive.
•
Configuring a Router as a TFTP Server
•
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Configuring Additional File Transfer Functions Configuring a Router as a Server FC-242 Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.1 In addition, you can configure the Cisco IOS software to forward extended BOOTP requests over asynchronous interfaces. Refer to the “Configuri...
Configuring Additional File Transfer Functions Configuring a Router as a Server FC-243 Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.1 Caution For full functionality, the software image sent to the client must be the same type as the ROM software installed on the client router...
Configuring Additional File Transfer Functions Configuring a Router as a Server FC-244 Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.1 The following example a router to send a copy of the file gs7-k.9.17 in Flash memory in response to a TFTP Read Request. The client router mus...
