RadioShack 63-1090 - Manual

setting your alarm

This product is equipped with a 2-minute
crescendo alarm.

1. Press

((•))

to switch to the alarm display.

2. Press and hold

((•))

again for 2 seconds. The

alarm hour digits blink.

3. Press

UP

or

DOWN

to change settings. Press

((•))

to confi rm.

activating your alarm

Press

to activate or deactivate the alarm.

shows in the clock and alarm area when the alarm
is activated.

silencing your alarm

When the alarm sounds, it will continue for 2
minutes. Press

SNOOZE

to silence it for 8 minutes.

Or, press

to turn it off until the next day.

If no button is pressed, the alarm will
automatically silence after 2 minutes. It will then

sound again after 8 minutes.

on fl at surfaces

Place the main unit indoors and the remote sensor
outdoors. Place them on fl at surfaces using their
respective stands (included).

wall mounting

1. Select an indoor wall for your main unit and an

outdoor wall for your remote sensor.

2. Remove the stands from the main unit and

remote sensor, respectively.

2. Drill a hole in the wall.

3. Thread a screw (not supplied) into the hole,

letting it extend about 3/16” from the wall.

4. Fit the head of the screw into the appropriate

keyhole slot.

Thank you for purchasing your Large Display Wireless
Indoor/Outdoor Thermometer from RadioShack. You can
mount it on a wall or place it on a fl at surface using the
included stand. Your thermometer can collect and display
indoor and outdoor temperature and humidity readings
from up to three sensors, and forecast weather.

main unit and stand

remote sensor

user’s guide

wire stand

63-1090

large display wireless

indoor/outdoor thermometer

Please read this user’s guide before

installing, setting up and using your new product.

www.radioshack.com

SNOOZE

MODE

Use to change the
display and settings.

and

Increase or decrease
setting and activate or
deactivate the Atomic
Clock.

((•))

Set alarm or view alarm
status.

Turn alarm on or silence
it for 24 hours.

CHANNEL

Switch remote sensors.

MEMORY

View current, maximum,
and minimum
temperature and
humidity readings.

PRESSURE

Change pressure
measurement units.

°C/°F

Select temperature
units.

Weather Forecast and
Barometric Trend Area

Outdoor Temeprature
and Humidity Area

Indoor Temperature and
Humidity Area

Clock and Alarm Area

The main unit requires three AA alkaline batteries
and the remote sensor requires two AAA alkaline
batteries for power. None are supplied; all are
available at RadioShack or online at
www.radioshack com.

For best results, always install batteries
in the remote sensor fi rst, and then in the
main unit.

1. Remove the battery compartment covers from the

main unit and remote sensor, respectively. If you are
using more than one sensor, select a different channel
for each sensor by switching

CHANNEL 1 2 3

.

2. Place the appropriate batteries in each compartment,

following the polarity symbols (+ and -) marked
inside.

3. Reset each unit and replace the battery compartment

covers.

RESET

RESET

Stand

Keyhole

Slot

This clock shows the current time and the day
of week in English, French, German, Italian,
or Spanish. The US Atomic Clock in Boulder,
Colorado, automatically updates the information
when the main unit is within 932 miles of a signal.
Initial reception takes 2—10 minutes. It is initiated
when you fi rst set up the unit and whenever you
press

RESET

. Once complete, the reception icon

will stop blinking.

1. Press and hold

MODE

for 2 seconds. The time

zone blinks.

2. Press MODE to select the time zone, hour,

minute, year, month, day, and language. Press

or

to set your desired setting. Press

MODE

to confi rm.

• The language options are E (English),

F (French), D (German), I (Italian), and
S (Spanish).

• The time zone options are PA (Pacifi c),

CE (Central), MO (Mountain), and EA (Eastern).

• Press MODE to toggle between Clock with

Seconds and Clock with Weekday display.

NOTE

CHANNEL 1 2 3

NOTE