RadioShack 61-140 - Manual

©2008.

RadioShack Corporation.

All rights reserved.

RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.

02A08

61-140

AO0305AAA1

Printed in China

61-140

Installing Batteries

1. Install three C batteries in your

Wireless Door Chime

as

indicated by the polarity symbols (+ and – ).

2. Install three AAA batteries in each

Remote Doorbell

as

indicated by the polarity symbols (+ and – ).

Notes

:

• Use only fresh batteries of the required size and type.
• Remove old or weak batteries that might leak and damage

electronic circuits.

• Don’t mix old and new batteries or battery chemistries.

Don’t mix old and new batteries or battery chemistries.

Changing the Channel

In the event you need to change or reset the channel on your

Wireless

Door Chime

and

Remote Doorbell

, use the following instructions.

1. Select the same channel (1, 2, or 3) in the

Wireless Door Chime

(remove batteries in

Wireless Door Chime

to select channel) and

Remote Doorbell 1

.

2. Repeat step 1 for

Remote Doorbell

2.

Note

: If your

Wireless Door Chime

rings when no one presses one of

the remotes, you may be receiving interference. Switch the affected

Wireless

Door Chime

and

Remote Doorbell

to another channel.

Mounting Your Wireless Door Chime

1. Drill a ¼-inch hole and insert an anchor.

2. Screw an M 3.5 screw into the anchor, leaving the head

extended about

1

/

8

-inch.

3. Align the

Wireless Door Chime

’s rear keyhole slot to the

screw head and slide the chime down to lock in place.

You can also set your

Wireless Door Chime

on a flat surface using

the attached metal stand.

Mounting Your Remote Doorbell

1. Mark two holes using the mounting bracket. Drill a ¼-inch

hole at each mark. Insert an anchor in each hole.

2. Align your mounting bracket with the anchors and screw

a supplied M 3.5 screw into each anchor.

3. Slide your

Remote Doorbell

into the bracket. To lock the

Remote Doorbell

in place, insert a supplied M 2.6 screw

into the bottom of the mounting bracket.

You can also carry your

Remote Doorbell

with you as a panic alarm or

to let someone you frequently visit (such as an elderly parent) know you
have arrived. If you want to use the supplied Lanyard:

1. Slip the thin, small end through the hole at the top of the

Remote

Doorbell

.

2. Thread the thick end through the loop at the thin end and pull

through.

Thank you for purchasing your Wireless Two-Bell Door Chime
from

RadioShack

. You can use it as a doorbell, remote pager,

or panic switch. Please read this user’s guide before installing,
setting up and using your new product.

What’s Included

Wireless Door Chime

Bell 1

Bell 2

Lanyard

Remote Mounting Bracket (2)

Anchor (5)

M 3 Screw (4)

M 2.6 Brass Screw (2)

M 3.5 Screw (5)

User’s Guide

Specifications

Frequency.............................................. 433.92 MHz ± 600 KHz
Doorbell current consumption ..................................... <10 mA
Chime current consumption ........................ <2 mA @ standby
........................................................................<130 mA @ chime
Chime battery low ................................................. 2.4 V ± 0.1 V
Chime audio power .......................... > 80 dBA @ 10 in (25 cm)
Doorbell operating temperature.......................–4° F to 140° F
...........................................................................(–20° C to 60° C)

Specifications are subject to change and improvement
without notice. Actual product may vary from the images
found in this document.

RF Emissions Information

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Consult your local

RadioShack

store or an experienced radio/TV

technician for help. If you cannot eliminate the interference, the
FCC requires that you stop using your door chime. Changes or
modifications not expressly approved by

RadioShack

may cause

interference and void the user’s authority to operate the equipment.

Limited Warranty

This product is warranted by

RadioShack

against manufacturing

defects in material and workmanship under normal use for ninety
(90) days from the date of purchase from

RadioShack

company-

owned stores and authorized

RadioShack

franchisees and dealers.

For complete warranty details and exclusions, check with your local

RadioShack

store.

RadioShack

Customer Relations

300 RadioShack Circle
Fort Worth, TX 76102

04/04

www.radioshack.com

Protect the environment by recycling used electronics. Go
to www.ecyclingcentral.com to find a recycling location
near you.

Preparation

Using Your Wireless Door Chime and Remote Doorbells

1. Slide your

Wireless Door Chime

to

ON

. Slide to

OFF

when you don’t

want to hear it ring.

2. Press one of your two

Remote Doorbells.

Your chime will “ding dong”

for

Remote Doorbell 1

and play “Home Sweet Home” for

Remote

Doorbell 2.

Adding Another Alarm

You can expand your doorbells to sound an
additional alarm. To do this, you will need
to wire one or both

Remote Doorbell

to an

alarm that contains a normally open contact.

1. Connect both tips of a 2-conductor wire

(not supplied) to a doorbell, as shown,
using two M3 screws.

2. Connect both tips of the other end of

the 2-conductor wire to the extra alarm.

Now, when you press your

Remote Doorbell

,

both the

Wireless Door Chime

and the alarm

will sound.

W ireless

Two-Bell Door Chime

Wireless Door Chime

Remote Doorbell

ON/OFF
Switch

BELL

¼” hole

CHANNEL 1 2 3

Remote Doorbell

Rear View

BELL 1
CHANNEL 3 2 1

BELL 2
CHANNEL 3 2 1