QSC WL3082 - Manual

*TD-000240-00*

TD-000272-00 revB

© Copyright 2007, QSC Audio Products, Inc.

QSC® is a registered trademark of QSC Audio Products, Inc.

“QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office

Speakon

®

is a registered trademark of Neutrik® and the names of Neutrik® products referenced herein are either trademarks and/or service marks of Neutrik®.

All trademarks are the property of their respective owners.

Panel-mount Neutrik

®

NL8

Speakon

®

Connectors

Amp Gain

-10 dB

Loudspeaker
Cables

Amplifier
Channels

Line-Level
Audio Cables

SC28

To House Left
Loudspeakers

To House Right
Loudspeakers

1±

1±

3±

3±

4±

4±

Subwoofer

Subwoofer

Low Frequency 1

Low Frequency 1

High Frequency

High Frequency

for inside shading of low frequency (audience
between the arrays) OR....

Set Amplifier Gain Controls to Same Setting.

Set SC28 “AMP GAIN” Value to Match Amplifier Setting.

Array Config

WL8 3way <LF>

Source Left

Source Right

Setup Highlights:

On the SC28, select:

for outside shading of low frequency (audience to-
ward the outside of the arrays).

2±

2±

Low Frequency 2

Low Frequency 2

1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA
Main (714) 754-6175 Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079
Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834

SC28 Triamp Connection Diagram for QSC’s WideLine-8 Loudspeaker System (WL3082)

In the

Setup Menu

…

•In the

Input Sens

menu, set the input sensitivity to correspond with expected audio source levels.

•In the

Array Config

menu, select the crossover type as

WL8 3way >LF<

for inside shading of low frequencies or

WL8 3way <LF>

for outside shading of low frequencies.

•In the

Array Size

menu, select the number of enclosures in each array.

•In the

Total Splay

menu, select the total of all the splay angles between the enclosures in each array. For more info go to http://www.qscaudio.com/products/dsp/sc28/sc28_array_compensation_eq.pdf

•In the

Subwoofer

menu, select the appropriate QSC sub, “None” for no sub, or “Bypass/Thru” to use an external crossover and EQ for the sub.

If the system includes subwoofers…

•In the

Sub Management

menu, configure the subwoofers as

Stereo

or

Summed Mono

.

•In the

Sub Gain

menu, adjust the level to compensate for the use of more or fewer subwoofers than a typical system.

•In the

Sub Delay

and

Array Delay

menus, you may add alignment delays if necessary. If the array is suspended below the subwoofer, the Sub Delay and Array Delay should be the same. If the

array is suspended in front of the subwoofer, the Array Delay should be 3.0 ms greater than the Sub Delay setting.

•In the

Limiters

menu, configure the output limiters to protect the loudspeakers or for clip limiting only of the SC28 output.

Disabling the loudspeaker protection is not recommended.

•In the

Out Amp

menus, select the QSC amplifier attached to each output.

•In the

Out Amp Cfg

menus, select whether each amplifier is configured as

Stereo

or

Bridge Mono

.

•In the

Amp Gain

menu, select the gain to match the gain control settings of the amplifiers connected to the outputs. All amplifiers must be set to the same value.

In the

EQ

Menu

…

•Adjust the equalization to compensate for environmental factors.

Array Config

WL8 3way >LF<