QLogic 59060-02 B - Manual

QLogic 59060-02 B

QLogic 59060-02 B – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
Page: / 62

Table of Contents:

  • Page 2 – Document Revision History; Revision B Changes
  • Page 3 – Table of Contents
  • Page 4 – Notes
  • Page 5 – Section 1; Introduction; This manual is organized as follows:; Intended Audience; The Fibre Channel Standards are available from:
  • Page 6 – Technical Support; Visit the QLogic support Web site listed in; Availability; , you may choose Electronic-Based Training or schedule an
  • Page 7 – Contact Information; Support Headquarters
  • Page 9 – Section 2; Events and Event Logging; Understanding Severity Levels; Events are classified by the following severity levels:; Displaying Events using the Event Browser; Show Event; button on the tool bar. When you close Enterprise; Save As; . For more information about the Event
  • Page 10 – Displaying the Events Using the Command Line Interface
  • Page 11 – Configuring the Event Log; logfile
  • Page 12 – Configuring Port Alarm Thresholds; Port Threshold Alarm
  • Page 13 – Section 3; Event Messages; Alarm Events
  • Page 15 – Contact your authorized maintenance provider.
  • Page 16 – Reduce the number zones on the remote switch.; operation is in progress); Try the activation or deactivation again later.
  • Page 19 – A remote switch sent a zone merge that was invalid.
  • Page 20 – A remote switch sent a merge request that was not understood.; being sent to remote switch on save, not supported in this mode); Enable Interop mode or change the zone membership type.
  • Page 21 – segment due to switches that do not support this zone member type); Edit the necessary zone sets to use WWN zone membership.
  • Page 22 – group members; Check the status of the remote switch.; not already in progress or fabric will be inconsistent); Deactivate the active zone set to keep the fabric consistent.
  • Page 24 – Change the domain ID on one of the conflicting switches.
  • Page 25 – Change the domain ID on one of the switches.
  • Page 26 – Modify the switches so that the time out values are the same.; to connect to remote switch); Change the port type on the remote switch to G_Port or GL_Port.
  • Page 27 – Add the switch to a group in the active security set.
  • Page 29 – Add the device to the port binding list.
  • Page 30 – verify MS security configuration)
  • Page 31 – the switch is hardreset)
  • Page 32 – IOStreamGuard Enabled)
  • Page 33 – Reconfigure the port to be compatible with the port hardware.
  • Page 34 – Binding is enabled, failing security checks); Check the security configuration on the remote switch.
  • Page 35 – Edit the ISL group to include the local switch.
  • Page 36 – authorized to login, verify MS security configuration); The port cannot login with the current security configuration.
  • Page 37 – shared secret
  • Page 38 – RADIUS authentication failed.; disabled on local switch.; Enable or disable fabric binding on all switches.; Authentication protocol in progress)
  • Page 44 – Reconfigure the port speed or replace the transceiver.
  • Page 45 – Critical Events; The fabric is already locked.
  • Page 47 – may take several seconds)
  • Page 48 – released automatically); New licenses are being installed.
  • Page 49 – configuration may have changed)
  • Page 50 – The SANdoctor bundle license was applied successfully.
  • Page 51 – The Fabric Security Bundle license was applied successfully.
  • Page 53 – held back until ISL up time is 5 seconds)
  • Page 54 – Warning Events; with domain ID domain_ID
  • Page 55 – Invalid user login attempt.
  • Page 56 – Informative Events; inband management is disabled on port port_number)
  • Page 57 – FDMI database has reached its configured limit.); A new zone set has been activated.
  • Page 59 – The session has been closed as a result of a configuration change.
  • Page 60 – The online test was canceled.
  • Page 61 – The user has removed a switch from the display.
Loading the manual

S i m p l i f y

R

59060-02 B

Page i

QLogic Fibre Channel Switch

Event Message Guide

Firmware Version 6

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Document Revision History; Revision B Changes

Page ii 59060-02 B S QLogic Fibre Channel Switch Event Message Guide © 2000–2006 QLogic Corporation. All Rights Reserved Worldwide. First Published: June 2006 QLogic Corporation, 26650 Aliso Viejo Parkway, Aliso Viejo, CA 92656, (800) 662-4471 or (949) 389-6000 Information furnished in this manual i...

Page 3 - Table of Contents

59060-02 B Page iii Table of Contents Section 1 Introduction 1.1 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.2 Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.3 Techn...

Page 4 - Notes

Page iv 59060-02 B QLogic Fibre Channel Switch Event Message Guide S Notes

Other QLogic Models

All QLogic Other