Powermatic PF3-JR - Manual - manualsarea.com

Page 2 - Warranty and Service; MORE INFORMATION; WHAT IS NOT COVERED?

2 Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can ...

Page 3 - Table of Contents

3 Table of Contents Warranty and Service .............................................................................................................................. 2 Warning..............................................................................................................................

Page 4 - not

4 W arning 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscur...

Page 7 - Features

Page 8 - Unpacking; Contents of the Shipping Container; or operation! Failure to comply may cause serious injury.

8 Unpacking Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the Stock Feeder is assembled and running properly. Compare the contents of your container with the following parts list...

Page 9 - Assembly and Installation; Tools needed for assembly:

9 Assembly and Installation Tools needed for assembly: 5mm hex wrench 12mm and 14mm open end wrenches Remove the clear plastic from around the feeder and stand. Exposed metal surfaces have been given a protective coating at the factory. This should be removed with a soft cloth moistened with a good ...

Page 11 - Grounding Instructions; Electrical connections must

11 Grounding Instructions Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be properly grounded to help prevent electrical shock and possible fatal injury. This Stock Feeder must be grounded. In the event of a malfunction or brea...

Page 12 - Extension Cords; Adjustments; Basic Feeder/Stand Movements

12 The green colored rigid ear, lug, or tab, extending from the adapter, must be connected to a permanent ground such as a properly grounded outlet box, as shown in Figure 7. Make sure the voltage of your power supply matches the specifications on the motor plate of the machine. Extension Cords If a...

Page 13 - Speed Selection; Unplug the stock feeder from

13 3. Loosen lock handle (B, Figure 10) and rotate the swivel cone (C, Figure 10) 180-degrees, as shown in Figure 10. 4. Re-tighten lock handle (B, Figure 10). 5. Loosen lock handle (D, Figure 10) and rotate the arm cone as needed until it can slide back onto the horizontal arm. Tighten locking hand...

Page 14 - Operating Controls; If a jam should occur while; Operation; Keep hands away from; General Operating Instructions

14 Operating Controls The control switch (Figure 14) turns the motor on, and also determines its direction – forward or reverse. If a jam should occur while feeding a workpiece, DO NOT turn the stock feeder to reverse while the auxiliary machine is still running in forward direction. If a workpiece ...

Page 15 - Although the stock feeder; When Used with a Shaper

15 6. When used in normal horizontal position, the stock feeder should be adjusted for height so that the distance between the table and the feed rollers is approximately 1/8” to 3/16” (3 to 5mm) less than the thickness of the workpiece. See Figure 15. Although the stock feeder when properly used wi...

Page 16 - When Used with a Table Saw; When Used with a Jointer; Roller Removal/Replacement; Maintenance; Before performing any

16 When Used with a Table Saw 1. Position the Stock Feeder so that the axis of the saw blade lines up between the center roller and infeed roller. See Figure 18. This will allow the Stock Feeder to grip the offcut of the workpiece as it leaves the blade. 2. Rotate the Stock Feeder so that the direct...

Page 17 - Lubrication; Gearbox; Rollers

17 The mating parts of the arm cone and swivel cone should be kept clean. See Figure 21. When disassembling any of the cones from the stock feeder, wipe off both mating parts with a clean rag before re-assembling. NOTE: These cones are subject to high torques and it may be necessary to periodically ...

Page 19 - Troubleshooting; Trouble Probable; Replacement Parts

19 Troubleshooting Trouble Probable Cause Remedy Not connected to power source. Check plug connection. Fuse blown, or circuit breaker tripped. Replace fuse, or reset circuit breaker. Cord damaged. Replace cord. Feeder will not start. Starting capacitor bad. Replace starting capacitor. Wrong gears in...

Page 24 - PF3-JR Electrical Connections

Page 25 - Boring Template

25 Boring Template SCALE 1:1 Cut out and tape into place on mounting surface.

Page 26 - NOTES