Polaroid PV 360 - Manual

9 Names and functions of each part (continued) Main power switch Used to turn the power on and off. : OFF : ON VIDEO IN jack S-VIDEO IN jack Mini DIN 4-pin connector VIDEO IN jack RCA jack AUDIO L/R IN jack RCA jack AC IN jack U s e d t o c o n n e c t t h eaccessory power cord. RGB IN jack D-sub 15...

10 Names and functions of each part (continued) Remote control transmitter FOCUS button U s e d t o a d j u s t t h e f o c u s o f t h e i m a g e o n t h escreen. (Refer to page 13.) ZOOM button Used to adjust the size of the image. (Refer topage 13.) FREEZE button Used to turn the freeze (still) ...

12 Installation Typical LCD Projector and Screen Installation Using the adjusters a. Distance from the LCD projector to the screenb.Distance from the lens center to the bottom of the screen (a,b : +/-10%). The projection distances shown in the diagram tothe left are for full size (1,024 x 768 dots)....

13 Basic operations To project 2 4 5 7 2 3 5 4 7 1 1 Turn on the main power switch of the projector [ I: ON]. • The Power indicator lights orange. 2 Press the STANDBY / ON button. • The Power indicator will blink green and then light green. • The green blinking indicates warmup. 3 Remove the lens ca...

14 Turning off the power Plug & Play Basic operations (continued) 1 Press the STANDBY/ON button for approximately 1 sec. • The Power indicator will blink orange, then the lamp will turn off. Approximately 1 sec. after that, the indicator will light orange. • After the power is turned off, the la...

15 Freeze function Basic operations (continued) 1 Press the FREEZE button. • The image being displayed will freeze.• The [ ] mark appears in the lower right corner of the screen when the Freeze function is on. 1 Press the FREEZE button. • The FREEZE function will be cancelled. • The [ ] mark will be...

16 1 Press the MAGNIFY + button. • The center part of the image will be displayed magnified approximately 2x. 2 Press the MAGNIFY + bu t t o n . • When this button is pressed, the image will be displayed even larger. 3 Press the MAGNIFY – button. • When this button is pressed, the image will be disp...

17 Returning to the initial settings Adjustments and functions 1 Press the MENU ( ) buttons of the projector or theMENU button of the remote control. • The Menu screen will appear. (refer to page 18 - 21 for details.) 2 Press the MENU ( ) buttons of the projector or the DISK PAD button of the remote...

18 Adjustments and functions (continu e d ) RGB signal input Video signal input • The menu cannot be displayed while the initial screen (“No input is detected.” or “Sync is out of range.”) is being displayed. • Tint cannot be adjusted with N-PAL, M-PAL, PAL or SECAM video signal input.• Tint, color ...

19 Adjustments and functions (continu e d ) INPUT The INPUT menu is used to select RGB signal sync signal frequency of the monitor and the VIDEO signal. Adjustment item RGB VIDEO Adjustment description Displays the following RGB inputs fH: horizontal sync frequencyfV: vertical sync frequency Sets th...

20 Adjustments and functions (continu e d ) Adjustment item KEYSTONE MIRROR BLANK START UP P in P Adjustment description Reduces keystone Reduces keystone distortion at the bottom distortion at the top Sets vertical or horizontal inversion of the projected image.H: horizontal inversion onlyV: vertic...

21 Adjustments and functions (continu e d ) OPT Communication functions, etc., can be set from the OPT menu. Adjustment item COM. SPEED COM. BITS TIMER LANGUAGE AUTO OFF SYNC ON G Adjustment description Sets the communication speed (5 steps). Sets the bit configuration for the communication data.7N1...

23 Connection to the RGB signal terminal (continued) • Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. •Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer. •Dependi...

25 Connecting the USB 1. Connect the projector and computer with a suitable commercially available cable. Disconnect the mouse cable from the projector. 2. Press the INPUT button of the projector or the RGB 1/2 button of the remote control and select the input where the computer is to be connected. ...

26 Connection to the control signal terminal Use the mouse cable provided or a PS/2 mouse cable (for IBM and compatibles). Cables for ADB mouse (Apple), bus mouse (NEC) and serial mouse are available as options. control jack D-sub 15-pin shrink jack Projector Computer Mouse jack Mini DIN 6-pin Mouse...

27 Connection to the control signal terminal (continu e d ) CONTROL signal jack ADB (Mac) mouse Projector Computer M o u s e j a c kMini DIN 4-pin Mouse cable (ADB) (option) Serial mouse Projector Computer Mouse jack D-sub 9-pin Mouse cable (serial) (option) Pin no. RS-232C Mouse PS/2 ADB Serial 1 2...

31 Example of system setup Cleaning the Air filter Turn power off to all devices before connecting. Refer to the instruction manual of each device before connecting. AC input Video tape recorder with S jack Video tape recorder Speaker (with built-in amp) Display monitor Computer (desktop type) Compu...

32 Cleaning the Air filter (continued) 3 Cleaning the air filter with a vacuum cleaner 4 Installing the air filter When the air filter becomes clogged with dust, etc., the projector power may turn off toprevent the internal heat level rising. (The lamp indicator color changes to red.)Do not operate ...

33 Message table (continued) Indicators The POWER indicator, LAMP indicator and TEMP indicator light or blink in the following cases. POWER indicator Lights orange Flashes green Lights green Flashes orange Lights red Lights red Lights red Flashes red LAMP indicator Turns off Turns off Turns off Turn...

34 Specifications Dimensional Diagram · These specifications are subject to change without notice. Unit: inches Product name Liquid crystal projector Model Polaroid360 Display method Three liquid crystal panels, three primary color system. Liquid crystal Panel size 3.3 cm (1.3 type) panel Drive syst...