Polaris 9921784 - Manual

4 INTRODUCTION The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and sym-bols are used. Become familiar with their meanings before reading the manual. The safety alert symbol indicates a potential personal injury hazard...

6 INTRODUCTION Vehicle Identification Numbers Record your vehicle's identification numbers and key number in the spaces provided. Remove the spare key and store it in a safe place. An ignition key can be duplicated only by ordering a Polaris key blank (using your key number) and mating it with one o...

7 SAFETY Safety Training ATV safety training is a top priority for Polaris. When you purchased your new ATV, your dealer instructed you on the authorized ATV RiderCourse sm available to you and your eligible family members. This training is included in the purchase price of your ATV. Polaris strongl...

8 SAFETY Safe Riding Gear Always wear appropriate clothing when riding an ATV. Wear protective clothing for comfort and to reduce the chance of injury. Helmet Wearing a helmet can prevent a severe head injury. Whenever riding a Polaris vehicle, always wear a helmet that meets or exceeds established ...

9 SAFETY Safe Riding Gear Eye Protection Do not depend on eyeglasses or sunglasses for eye protection. When-ever riding a Polaris vehicle, always wear shatterproof goggles or use a shatterproof helmet face shield. Polaris recommends wearing approved Personal Protective Equipment (PPE) bearing markin...

10 SAFETY Safety Warnings Failure to operate the ATV properly can result in a collision, loss of control, accident or overturn, which may result in serious injury or death. Heed all safety warnings outlined in this section of the owner’s manual. See the OPERATION section of the owner’s manual for pr...

11 SAFETY Safety Warnings Handling Gasoline Gasoline is highly flammable and explosive under certain conditions. • Always exercise extreme caution whenever handling gasoline.• Always refuel with the engine stopped, and outdoors or in a well ventilated area. • Do not smoke or allow open flames or spa...

12 SAFETY Safety Warnings Protective Apparel Riding in this vehicle without wearing an approved helmet and protective eyewear increases the risk of a serious injuries in the event of an accident.Operator and passenger must always wear an approved helmet that fits properly and eye protection (goggles...

13 SAFETY Safety Warnings Operating on Pavement Operating an ATV on paved surfaces (including sidewalks, paths, parking lots and driveways) may adversely affect the handling of the ATV and could result in loss of control and accident or overturn.Avoid operating the ATV on pavement. ATV tires are des...

14 SAFETY Safety Warnings Physical Control of the ATV Removing a hand from the handlebars or feet from the footrests during operation can reduce your ability to control the vehicle or cause loss of balance and ejection from the ATV. If the operator's foot is not firmly planted on the footrest, it co...

15 SAFETY Safety Warnings Descending Hills Improperly Improperly descending a hill could cause loss of control or overturn.• Always follow proper procedures for travel- ing down hills as described in the owner's manual. NOTE: A special technique is required when braking while traveling down-hill. Se...

16 SAFETY Safety Warnings Stalling While Climbing a Hill Stalling, rolling backwards or improperly dismounting while climbing a hill could cause an overturn.• Always maintain a steady speed when climbing a hill. If all forward speed is lost:• Keep body weight uphill.• Apply the single-lever brake gr...

17 SAFETY Safety Warnings Operating on Slippery Terrain Failure to use extra caution when operating on excessively rough, slippery or loose terrain could cause loss of traction, loss of control, accident or overturn.Do not operate on excessively rough, slippery or loose terrain. Always use extra cau...

18 SAFETY Safety Warnings Operating Improperly in Reverse Improperly operating in reverse could result in a collision with an obstacle or person. Always follow proper operating procedures as outlined in this manual. See page 52. Before shifting into reverse gear, always check for obstacles or people...

19 SAFETY Safety Warnings Operating Over Obstacles Improperly operating over obstacles could cause loss of control or overturn.Before operating in a new area, check for obstacles. Avoid operating over large obstacles such as rocks and fallen trees. If unavoidable, use extreme caution and always foll...

20 SAFETY Safety Warnings Improper Cargo Loading Overloading the ATV or carrying/towing cargo improperly may cause changes in handling, which could cause loss of control or an accident.• Never exceed the stated load capacity for this ATV.• Cargo should be properly distributed and securely attached.•...

21 SAFETY Safety Warnings Operating a Damaged ATV Operating a damaged ATV can result in an accident. After any overturn or accident, have a qualified service dealer inspect the entire machine for possible damage, including (but not limited to) brakes, throttle and steering systems. Physical Skills S...

22 SAFETY Safety Labels and Locations Warning labels have been placed on the vehicle for your protection. Read and follow the instructions on each label carefully. If any of the labels shown in this manual differ from the labels on your vehicle, always read and follow the instructions of the labels ...

23 SAFETY Safety Labels and Locations Discretionary Warning WARNING• Never operate this ATV on HILLS steeper than 25 degrees 25 ° . To pre- vent overturn on hilly terrain, use throttle and brakes gradually, and shift weight uphill. • REVERSE operation can be dangerous even at low speeds. Steering be...

24 SAFETY Safety Labels and Locations “No Passenger” Warning WARNINGNEVER ride as a passenger.Passengers can cause a loss of control, resulting in SEVERE INJURY or DEATH. 7175378 Tire Pressure/Load Warning WARNINGImproper tire pressure or overloading can cause loss of control. Loss of control can re...

25 SAFETY Safety Labels and Locations Age 16 Warning WARNINGOperating this ATV if you are under the age of 16 increases your chance of severe injury or death.NEVER operate this ATV if you are under age 16. 7175374 Clutch Cover Warning WARNING• Moving parts hazard under belt-clutch guard. To prevent ...

26 FEATURES AND CONTROLS Switches Override Switch This vehicle is equipped with a reverse speed limiter system. To gain additional wheel speed while backing, release the throttle and press the override switch. WARNING! Pressing the override switch while the throttle is open can cause loss of control...

27 FEATURES AND CONTROLS Switches Headlight Switch Use the headlight switch to turn the lights on and off and to change the lights from high beam to low beam (if equipped). The key must be in the ON position and the engine stop switch must be in the RUN position to operate the headlights. Indicator ...

28 FEATURES AND CONTROLS Throttle Lever Operating an ATV with sticking or improperly operating throttle controls could cause an accident. Never start or operate an ATV that has a sticking or improperly operating throttle. Always contact your dealer for service before operating the vehicle.Failure to...

29 FEATURES AND CONTROLS Brake Lever Operating the ATV with a spongy brake lever can result in loss of braking, which could cause an accident. Never operate the ATV with a spongy-feeling brake lever. Always contact your dealer for service before operating the vehicle. Squeeze the brake lever toward ...

30 FEATURES AND CONTROLS Auxiliary Foot Brake Aggressively applying the auxiliary brake when backing down a hill may cause rear tipover, which could result in serious injury or death. Never back down a hill.Use caution when applying the auxiliary brake. Do not aggressively apply the auxiliary brake ...

31 FEATURES AND CONTROLS Brake Fluid An over-full master cylinder may cause brake drag or brake lock-up, which could result in an accident. Maintain brake fluid at the recommended level. Do not overfill.Never store or use a partial bottle of brake fluid. Brake fluid is hygroscopic, meaning it rapidl...

32 FEATURES AND CONTROLS Brake Fluid Hand Brake Check the brake fluid level in the master cylinder before each use of the vehicle. The master cylinder is located on the left handlebar. Maintain the fluid level 1/4" (6 mm) below the top edge of the master cylinder. Do not overfill. 1. Position th...

33 FEATURES AND CONTROLS Choke The choke assists in starting a cold engine. Refer to the engine starting procedure on page 41 for correct choke and throttle settings during start-ing. Fuel Tank Cap Always refuel with the engine stopped, and outdoors or in a well ventilated area. Refuel on a level su...

34 FEATURES AND CONTROLS Automatic Transmission Gear Selector The transmission gear selector is located on the right side of the vehicle. F: Forward GearN: NeutralR: Reverse To shift gears, brake to a complete stop. When the engine is idling, move the lever to the desired gear. NOTICE: Shifting gear...

35 FEATURES AND CONTROLS Recoil Starter If the battery is too weak to start the engine, use the recoil starter. Follow the starting procedures on page 41, cranking the engine with the recoil starter instead of the main key switch. 1. Grasp the recoil starter rope handle tightly. 2. Pull slowly so yo...

36 OPERATION Failure to operate the ATV properly can result in a collision, loss of control, accident or overturn, which may result in serious injury or death. Read and understand all safety warnings outlined in the safety section of this owner’s manual. Break-In Period The break-in period for your ...

37 OPERATION Break-In Period Engine and Drivetrain Break-in 1. Fill the fuel tank with gasoline. See page 33. Always exercise extreme caution whenever handling gasoline. 2. Check the oil level on the dipstick. See page 62. Add oil if neces- sary to maintain the level in the safe operating range. 3. ...

38 OPERATION Safe Operation Practices 1. Complete the recommended safety training before operating this vehicle. See page 7. 2. Do not allow anyone under 16 years of age to operate this vehicle. Do not allow anyone with cognitive or physical disabilities to oper-ate this vehicle. 3. Never carry a pa...

39 OPERATION Know Your Riding Area/Tread Lightly Familiarize yourself with all laws and regulations concerning the opera-tion of this off-road vehicle in your area. Respect the environment in which you ride. Find out where the designated riding areas are by con-tacting your Polaris dealer, a local r...

40 OPERATION Pre-Ride Checklist Failure to inspect and verify that the ATV is in safe operating condition before operating increases the risk of an accident. Always inspect the ATV before each use to make sure it's in safe operating condition. Item Remarks Page Brake system/lever travel Ensure prope...

41 OPERATION Starting the Engine 1. Position the vehicle on a level surface outdoors or in a well-venti- lated area. 2. Place the transmission in neutral. 3. Lock the parking brake. Tip: The starter interlock will prevent the engine from starting if the transmission is in gear and the brake is not e...

42 OPERATION Starting the Engine 9. Turn the ignition key past the ON position to engage the starter. Activate the starter for a maximum of five seconds, releasing the key when the engine starts. NOTICE: Operating the vehicle immediately after starting could cause engine damage. Allow the engine to ...

43 OPERATION Driving Procedures 1. Wear a helmet and eye protection. See page 8. 2. Sit upright with both feet on the footrests and both hands on the handlebars. 3. Start the engine and allow it to warm up. 4. Shift the transmission into gear. 5. Check your surroundings and determine your path of tr...

44 OPERATION Turning the Vehicle Your ATV is equipped with a solid rear axle, which drives both rear wheels equally at all times. This means that the wheel on the outside of the turn must travel a greater distance than the inside wheel when turning and the inside tire must slip traction slightly. To...

45 OPERATION Driving on Slippery Surfaces Whenever riding on slippery surfaces such as wet trails or loose gravel, or during freezing weather, follow these precautions: 1. Do not operate on excessively rough, slippery or loose terrain. 2. Slow down when entering slippery areas. 3. Engage AWD before ...

46 OPERATION Driving Uphill Braking and handling are greatly affected when operating in hilly ter-rain. Improper procedure could cause loss of control or overturn. When-ever traveling uphill, follow these precautions: 1. Drive straight uphill. 2. Avoid steep hills (25 ° maximum). 3. Always check the...

47 OPERATION Driving on a Sidehill (Sidehilling) Driving on a sidehill is not recommended. Improper procedure could cause loss of control or overturn. Avoid crossing the side of any hill unless absolutely necessary. If crossing a sidehill is unavoidable , follow these precautions: 1. Slow down. 2. A...

48 OPERATION Driving Downhill When driving downhill, follow these precautions: 1. Avoid steep hills (25 ° maximum). 2. Shift body weight uphill. 3. Drive straight downhill. 4. Slow down. Excessive speed when traveling downhill can cause loss of control. 5. Squeeze the brake lever gradually. Applying...

49 OPERATION Turning Around on a Hill (K-Turn) If the vehicle stalls while climbing a hill, never back it down the hill! Use the K-turn to turn around. 1. Stop and lock the parking brake while keeping body weight uphill. 2. Leave the transmission in forward and shut off the engine. 3. Dismount on th...

50 OPERATION Driving Through Water Your ATV can operate through water with a maxi-mum recommended depth equal to the bottom of the footrests. Follow these pro-cedures when operating through water: 1. Determine water depths and current before entering water. 2. Choose a crossing where both banks have...

51 OPERATION Driving Over Obstacles Follow these precautions when operating over obstacles: 1. Always check for obstacles before operating in a new area. 2. Look ahead and learn to read the terrain. Be constantly alert for haz- ards such as logs, rocks and low hanging branches. 3. Travel slowly and ...

52 OPERATION Driving in Reverse Follow these precautions when operating in reverse: 1. Always check for obstacles or people behind the vehicle. 2. Always avoid backing downhill. 3. Back slowly. 4. Apply the brakes lightly for stopping. 5. Avoid turning at sharp angles. 6. Never open the throttle sud...

53 OPERATION Parking on an Incline Avoid parking on an incline if possible. If it's unavoidable, follow these precautions: 1. Stop the engine. 2. Place the transmission in gear. 3. Lock the parking brake. 4. Always block the rear wheels on the downhill side. 5. Turn the fuel valve off.

54 OPERATION Hauling Cargo Overloading the vehicle or carrying or towing cargo improperly can alter vehicle handling and may cause loss of control or brake instability, which can result in serious injury or death. Always follow these precautions when hauling cargo:REDUCE SPEED AND ALLOW GREATER DIST...

55 OPERATION Hauling Cargo Never exceed the weight capacities specified for your ATV on warning labels and in the specifications section of this manual. Cargo weight should be evenly distributed (1/3 on the front rack and 2/3 on the rear rack) and mounted as low as possible. When operating over roug...

56 EMISSION CONTROL SYSTEMS Noise Emission Control System Do not modify the engine, intake or exhaust components, as doing so may affect compliance with U.S.A. EPA noise control requirements (40 CFR 205) and local noise level requirements. Operation on Public Lands in the U.S.A. Your Polaris vehicle...

57 MAINTENANCE Periodic Maintenance Chart Careful periodic maintenance will help keep your vehicle in the safest, most reliable condition. Inspection, adjustment and lubrication of important components are explained in the periodic maintenance chart. Inspect, clean, lubricate, adjust and replace par...

58 MAINTENANCE Periodic Maintenance Chart Improperly performing the procedures marked with a „ could result in component failure and cause an accident, which may result in serious injury or death. Always have an authorized Polaris dealer perform these services. Maintenance Chart Key X Perform these ...

61 MAINTENANCE Lubrication Guide Check and lubricate all components at the intervals outlined in the Peri-odic Maintenance Chart beginning on page 57. Items not listed in the chart should be lubricated at the General Lubrication interval. See page 103 for the part numbers of Polaris products. The a-...

62 MAINTENANCE Engine Oil Oil Recommendations Polaris recommends the use of Polaris PS-4 PLUS Performance Syn- thetic 2W-50 4-cycle oil or a similar oil for this engine. Oil may need to be changed more frequently if Polaris oil is not used. Always use 2W-50 oil. Follow the manufacturer's recommendat...

63 MAINTENANCE Oil and Filter Change Always change the oil and filter at the intervals outlined in the Periodic Maintenance Chart beginning on page 57. Always change the oil filter whenever changing oil. 1. Position the vehicle on a level surface. Place the transmission in neutral. Lock the parking ...

64 MAINTENANCE Transmission Oil Always check and change the transmission oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 57. Polaris recommends the use of Polaris Premium AGL Synthetic Gearcase Lube. See page 103 for the part numbers of Polaris products. Transmissio...

65 MAINTENANCE Transmission Oil Oil Change 1. Position the vehicle on a level surface. 2. Place a drain pan beneath the transmission oil drain plug area. 3. Loosen the jam nut. 4. Turn the adjuster bolt in to allow the removal of the drain plug. 5. Remove the drain plug and wipe the magnetic end cle...

66 MAINTENANCE Brakes The front and rear brakes are hydraulic disc brakes, activated by moving the single brake lever toward the handlebar. The auxiliary foot brake is also hydraulic. Both brake systems are self-adjusting. Brake Inspections The following checks are recommended to keep the brake syst...

67 MAINTENANCE Side Panel Removal Tip: Side panel removal may be difficult until the locking tabs and receivers have been snapped and unsnapped a few times. 1. Remove the seat. 2. Grasp the rear of the side panel near the rear cab. With a quick and firm motion, pull the panel forward and outward to ...

68 MAINTENANCE Toe Alignment Use the following procedure to check the toe alignment of the vehicle. The recommended toe alignment is 1/8" to 1/4" (3-6 mm) toe out. WARNING! Severe injury or death can result from improper toe alignment and adjustment. Do not attempt to adjust tie rod alignmen...

69 MAINTENANCE Throttle Cable Freeplay Adjust throttle cable freeplay at the handlebar. 1. Locate the throttle cable adjuster at the handlebar. 2. Squeeze the end of the rub- ber boot and slide it far enough to expose the end of the inline cable adjuster. 3. Loosen the adjuster lock nut. 4. Rotate t...

70 MAINTENANCE Camber and Caster The camber and caster are non-adjustable. Rear Spring The rear shock absorber spring is adjusted by rotating the adjuster either clockwise or counterclockwise to increase or decrease spring tension. Accessory springs are available through your Polaris dealer. Handleb...

71 MAINTENANCE Tires Operating your ATV with worn tires, improperly inflated tires, non-standard tires or improperly installed tires will affect vehicle handling and could cause an accident resulting in serious injury or death. Always follow all tire maintenance procedures as outlined in this manual...

72 MAINTENANCE Tires Wheel Removal 1. Position the vehicle on a level surface. Place the transmission in gear. Lock the parking brake. 2. Loosen the wheel nuts slightly. WARNING! Do not service axle nuts that have a cotter pin installed. See your Polaris dealer. 3. Place a suitable stand under the f...

73 MAINTENANCE Tires Wheel Nut Torque Specifications Check the wheel nut torques occasionally and when they've been loos-ened for service. Item Torque Specification Front Wheel Nuts 27 ft. lbs. (37 Nm) Rear Wheel Nuts 50 ft. lbs. (68 Nm) Rear 50 ft. lbs. (68 Nm) Front 27 ft. lbs. (37 Nm)

74 MAINTENANCE Air Filter 1. Position the vehicle on a level surface. Place the transmission in gear. Lock the parking brake. 2. Remove the seat. 3. Release the air box cover clips, and remove the air box cover. 4. Loosen the clamp and remove the filter. 5. Remove the pre-filter from the main filter...

75 MAINTENANCE Recoil Housing Always drain the recoil housing after operating the vehicle in wet condi-tions. Drain the housing before storing the vehicle. Make sure the hous-ing is completely dry before reinstalling the drain plug. Water will enter the recoil housing if the starter handle is diseng...

76 MAINTENANCE Carburetor Your Polaris ATV is calibrated at the factory for optimal performance at altitudes ranging from zero to 6,000 feet (1800 m) and temperatures of +40 degrees F. (4 degrees C.) or higher. Above 6000 feet (1800 m) the engine air/fuel mixture becomes overly rich and the engine l...

77 MAINTENANCE Drive Chain Drive Chain Lubrication Polaris ATV drive chains are equipped with o-ring-sealed, permanently greased pins and rollers. However, the outer surfaces of the roller must be lubricated. Always inspect the drive chain prior to operating the vehicle. Check for damaged or missing...

78 MAINTENANCE Drive Chain Rear Drive Chain Slack Check the amount of chain slack in three different locations by moving the vehicle slightly forward to gain slack at the top side of the rear chain. Measure the chain slack at the tightest of the three positions. At this point the chain should have 3...

79 MAINTENANCE Drive Chain Rear Drive Chain Slack 6. Roll the ATV forward or backward to adjust the chain slack to the proper tension. See the illustration for proper splice link clip opening position. 7. Tighten the eccentric locking bolts to 30 ft. lbs. (41 Nm) for machines without the hitch and 4...

80 MAINTENANCE Lights Headlight Beam Adjustment The headlight beam can be adjusted slightly upward or downward. Use the following procedure to make the adjustment. 1. Position the vehicle on a level surface with the headlight approxi- mately 25 ft. (7.6 m) from a wall. 2. Place the transmission in n...

81 MAINTENANCE Lights Poor lighting can result in reduced visibility when driving. Headlight and taillight lenses become dirty during normal operation. Clean lights frequently and replace burned out lamps promptly. Always make sure lights are adjusted properly for best visibility. Headlamp Replaceme...

82 MAINTENANCE Lights Taillight/Brakelight Lamp Replacement 1. Remove the taillight lens cover mounting screws. Remove the lens cover and gasket and set aside for reassembly. 2. Remove the lamp. 3. Apply dielectric grease to the socket and install the new lamp. 4. Test the taillight/brake light for ...

83 MAINTENANCE Spark Plugs Spark Plug Recommendations Refer to the specifications section beginning on page 108 for the recom-mended spark plug type and gap for your vehicle. Torque spark plugs to specification. NOTICE: Using non-recommended spark plugs can result in serious engine damage. Always us...

84 MAINTENANCE Spark Plugs Spark Plug Condition Normal Spark Plug The normal insulator tip is gray, tan or light brown. There will be few combustion deposits. The electrodes are not burned or eroded. This indi-cates the proper type and heat range for the engine and the service. The tip should not be...

85 MAINTENANCE Vehicle Immersion If your vehicle becomes immersed, major engine damage can result if the machine is not thoroughly inspected. Take the vehicle to your dealer before starting the engine. If it's impossible to take your ATV to a dealer before starting it, follow the steps outlined belo...

86 MAINTENANCE Spark Arrestor Failure to heed the following warnings while servicing the spark arrestor could result in serious injury or death. Never run the engine in an enclosed area. Remove any combustible materials from the area. Wear eye protection and leather work gloves. Do not stand behind ...

87 MAINTENANCE PVT System Failure to comply with the instructions in this warning can result in severe injury or death. Do not modify any component of the PVT system. Doing so may reduce its strength so that a failure may occur at a high speed. The PVT system has been precision balanced. Any modific...

89 MAINTENANCE PVT System PVT Drying There may be some instances when water is accidently ingested into the PVT system. Use the following instructions to dry it out before operat-ing. 1. Move the vehicle out of the water. 2. Remove the PVT drain plug. Allow the water to drain completely. Reinstall t...

90 MAINTENANCE Battery Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negative (black) cable last. Bat...

91 MAINTENANCE Battery Battery Removal 1. Place the transmission in gear. 2. Lock the parking brake. 3. Disconnect the battery hold-down strap. 4. Remove the battery cover. 5. On conventional batteries, remove the battery vent tube. 6. Disconnect the black (negative) battery cable first. 7. Disconne...

92 MAINTENANCE Battery Battery Installation Using a new battery that has not been fully charged can damage the bat-tery and result in a shorter life. It can also hinder vehicle performance. Follow the battery charging instructions on page 94 before installing the battery. 1. Ensure that the battery ...

93 MAINTENANCE Battery Battery Storage Whenever the vehicle is not used for a period of three months or more, remove the battery from the vehicle, ensure that it's fully charged, and store it out of the sun in a cool, dry place. Check battery voltage each month during storage and recharge as needed ...

94 MAINTENANCE Battery Battery Charging (Conventional Battery) 1. Remove the battery from the vehicle to prevent damage from leak- ing or spilled electrolyte during charging. See page 91. 2. Charge the battery with a charging output no larger than 1/10 of the battery’s amp/hr rating. Charge as neede...

95 MAINTENANCE Battery Battery Charging (Sealed Battery) Always verify battery condition before and 1-2 hours after the end of charging. State of Charge Voltage Action Charge Time (Using constant current charger @ standard amps specified on top of battery) 100% 12.8-13.0 volts None, check at 3 mos. ...

96 MAINTENANCE Cleaning and Storage Washing the Vehicle Keeping your Polaris vehicle clean will not only improve its appearance but it can also extend the life of various components. NOTICE: High water pressure may damage components. Polaris recommends washing the vehicle by hand or with a garden ho...

97 MAINTENANCE Cleaning and Storage Washing the Vehicle If a high pressure water system is used for cleaning (not recommended), exercise extreme caution. The water may damage components and could remove paint and decals. Avoid directing the water stream at the follow-ing items: If an informational o...

98 MAINTENANCE Cleaning and Storage Chrome Wheel Care (if equipped) Proper maintenance will protect chrome wheels from corrosion, pre-serve wheel life and ensure a “like new” appearance for many years. Chrome wheels exposed to road salt (or salt in the air in coastal areas) are more susceptible to c...

99 MAINTENANCE Cleaning and Storage Storage Tips NOTICE: Starting the engine during the storage period will disturb the protective film created by fogging and damage could occur. Never start the engine during the storage period. Clean the Exterior Make any necessary repairs and clean the vehicle as ...

100 MAINTENANCE Cleaning and Storage Storage Tips Fluid Levels Inspect the fluid levels. Change fluids as recommended in the Periodic Maintenance Chart beginning on page 57.• Demand drive unit (front gearcase)• Transmission• Brake fluid (change every two years and any time the fluid looks dark or co...

101 MAINTENANCE Cleaning and Storage Storage Tips Inspect and Lubricate Inspect all cables and lubricate all areas of the vehicle as recommended in the Periodic Maintenance Chart beginning on page 57. Battery Storage See pages 93-94 for storage and charging procedures. Storage Area/Covers Set the ti...

102 MAINTENANCE Transporting the Vehicle Follow these procedures when transporting the vehicle. 1. Stop the engine. 2. Place the transmission in gear. 3. Lock the parking brake. 4. Turn the fuel valve off. 5. Secure the fuel cap, oil cap and seat. 6. Remove the key to prevent loss during transportin...

103 POLARIS PRODUCTS Part # Description Engine Lubricant 2870791 Fogging Oil (12 oz. Aerosol) 2876244 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (qt./.95 l) 2876245 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (gal./3.8 l) Gearcase / Transmission Lubricants 2873602 Premium AGL Synthetic ...

104 TROUBLESHOOTING Drive Belt Wear/Burn Possible Cause Solution Starting out going up a steep incline Use low range (if equipped) or turn around using the K-turn (see page 49). Driving at low RPM or ground speed (3-7 MPH) Drive at a higher speed or use low range (if equipped) more frequently. Insuf...

105 TROUBLESHOOTING Engine Doesn't Turn Over Engine Turns Over, Fails to Start Engine Backfires Possible Cause Solution Low battery voltage Recharge the battery to 12.8 VDC Loose battery connections Check all connections and tighten Loose solenoid connections Check all connections and tighten Possib...

106 TROUBLESHOOTING Engine Pings or Knocks Engine Runs Irregularly, Stalls or Misfires Possible Cause Solution Poor quality or low octane fuel Replace with recommended fuel Incorrect ignition timing See your dealer Incorrect spark plug gap or heat range Set gap to specs or replace plugs Idle set too...

107 TROUBLESHOOTING Engine Stops or Loses Power Possible Cause Solution Out of fuel Turn fuel valve to reserve, refuel Kinked or plugged fuel vent line Inspect and replace Water is present in fuel Replace with new fuel Overuse of choke Inspect, clean and/or replace spark plugs Fouled or defective sp...

108 SPECIFICATIONS * Based on EU Directive 76/432/EC Trail Boss 330 Maximum Weight Capacity 415 lbs. (188 kg) (includes weight of opera-tor, cargo and accessories) Dry Weight 505 lbs. (229 kg) Fuel Capacity 3.25 gal. (12.3 l) Engine Oil Capacity 1.9 qts. (1.8 l) (with oil cooler)1.7 qts. (1.6 l) (oi...

109 SPECIFICATIONS Jetting Chart Clutching Chart Trail Boss 330 Driving System Type Automatic PVT (Polaris Variable Transmission) Shift Type Side Lever (F/N/R) Gear Reduction, Reverse 3.05:1 Gear Reduction, Forward 2.68:1 Drive Ratio, Final 3.64:1 Drive Chain 520 O-Ring Tires/Pressure, Front 23 x 7-...

110 WARRANTY LIMITED WARRANTY Polaris Sales Inc., 2100 Highway 55, Medina, MN 55340, gives a SIX MONTH LIM-ITED WARRANTY on all components of the Polaris All Terrain Vehicle (ATV) against defects in material or workmanship. Polaris also gives a one year limited warranty on the final drive chain for ...

112 WARRANTY ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-TICULAR PURPOSE) ARE LIMITED IN DURATION TO THE ABOVE SIX MONTH WARRANTY PERIOD. POLARIS FURTHER DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY. Some states...

113 WARRANTY Exported Vehicles EXCEPT WHERE SPECIFICALLY REQUIRED BY LAW, THERE IS NO WAR-RANTY OR SERVICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER'S AUTHORIZED LOCA-TION.This policy does not apply to vehicles that have received authorization for expo...

114 WARRANTY Exported Vehicles How to Get Service If Purchased From A Private Party: If you purchase a Polaris product from a private citizen outside of the country in which the vehicle was originally purchased, all warranty coverage will be denied. Notice If your vehicle is registered outside of th...

116 MAINTENANCE LOG Present this section of your manual to your dealer each time your vehicle is serviced. This will provide you and future owners with an accurate log of maintenance and ser-vices performed. DATE MILES (KM) OR HOURS TECHNICIAN SERVICE PERFORMED / COMMENTS