Planar PT1814NUV - Manual - manualsarea.com

Page 3 - Preface; REFACE; FCC Compliance Statement; Class B ITE

Preface i P REFACE FCC Compliance Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is opera...

Page 4 - User’s Manual; Important Safety Instructions; The power or Monitor-to-PC signal cord is frayed or damaged.

User’s Manual ii Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean the LCD Monitor screen, first, make sure the Monitor is in the power off mode. Unplug the Monitor from its power source before cleaning it. Do n...

Page 5 - Table of Contents; ABLE OF

Table of Contents iii T ABLE OF C ONTENTS PREFACE .............................................................................................................................................................................. I TABLE OF CONTENTS ..........................................................

Page 7 - HAPTER; The LCD Monitor; Your new LCD Monitor!; Identifying Components

1 C HAPTER 1 The LCD Monitor Your new LCD Monitor! Your LCD Monitor has been designed to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640 x 480 VGA to 1280 x 1024 SXGA. The digital controls located on the front panel allow the user to easil...

Page 9 - Chapter 1; The LCD Monitor — Rear View; Adjusting the Viewing Angle

Chapter 1 3 The LCD Monitor — Rear View 1. Input signal ports The monitor can accept signal input from either a traditional analog 15-pin D-Sub VGA connector or the 24-pin Digital Video Interface (DVI) connector. If both cables are connected, the Input Port option in the OSD can select which video i...

Page 10 - Positioning; Connecting AC Power

User’s Manual 4 Do not force the Monitor past its maximum extension in either direction. You could damage the Monitor and the Monitor stand. Positioning Take a moment to prepare a suitable place to set up your workstation. You need a stable flat dust-free surface with good ventilation. Even though t...

Page 11 - Connecting the Stereo Speakers; Connecting the Optional Touch Screen

Chapter 1 5 3. Make sure the signal cable is secure to both the monitor and PC. Tighten the connecting screws to ensure a secure connection. If both analog (15-pin D-sub VGA) and digital (24-pin DVI) input ports are connected at the same time, the signal input can be selected with the OSD (On-Screen...

Page 12 - Power Management System

User’s Manual 6 2. Connect the D-sub 9-pin RS232 connector end of the PS/2 to RS232 cable provided with the optional touch screen package to the 9-pin RS232 serial port at the back of your PC. 3. Install the Touch Screen Drivers to your PC. 4. Following the Touch Screen driver guide to align your to...

Page 13 - The Display Controls; The LCD Monitor’s Display Controls; or up; Main Menu; NCTION

7 C HAPTER 2 The Display Controls The LCD Monitor’s Display Controls This chapter covers the LCD Monitor’s On Screen Display (OSD). Using the OSD you can adjust the contrast, brightness, display position, display clarity, and color temperature, etc. You can also adjust the stereo speaker volume and ...

Page 14 - Basic Setting

User’s Manual 8 Basic Setting CONTRAST To adjust the contrast level of the display. BRIGHTNESS To adjust the brightness level of the display. VIDEO LEVEL Fine tuning the input signal voltage level. Perform this function whenever the PC graphic card is changed. GAMMA To select a suitable color repres...

Page 15 - Chapter 2

Chapter 2 9 No Signal coming… When the monitor is ON and there is no Video signal received, the monitor will enter the power saving mode. Check the video cable connection. Signal out of monitor’s supported range When the either the display resolution or refresh rate is beyond the capabilities of the...

Page 16 - PPENDIX; Technical Information; TFT LCD Monitor Specifications

10 A PPENDIX A Technical Information TFT LCD Monitor Specifications Model Planar PT1814N LCD Panel 18.1” SXGA Control Functions Power Rocker switch with LED indicator On-Screen Display (OSD) BASIC SETTING----- CONTRAST/BRIGHTNESS/VIDEO LEVEL/GAMMA/FRAME POSITION-------------- CLOCK/PHASE/DEFAULT SIZ...

Page 17 - Supported Timing; Timing for Model PT1814N (SXGA Resolution); *Specifications are subject to change without notice.

11 A PPENDIX B Supported Timing Timing for Model PT1814N (SXGA Resolution) Item Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) Sync Polarity or composite sync (H/V) Operating Mode 1 NEC PC98 640x400 25.20 70.15 31.50 -/- A/D 2 NEC PC98 640x4...

Page 18 - Troubleshooting; Troubleshooting Procedures

12 A PPENDIX C Troubleshooting Troubleshooting Procedures This LCD Monitor was pre-adjusted in the factory with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is select...

Page 19 - Optional Video input function; Monitor with optional Video input function; Video Control functions; Function

13 A PPENDIX D Optional Video input function Monitor with optional Video input function If your LCD Monitor is with Video input function, the display can be directly connected to a Video device such as VCR, DVD, camcorder etc. for Video display. The Monitor is compatible with NTSC/PAL systems. OSD M...

Planar PT1814NUV - Manual

Table of Contents:

Summary

Other Planar Models