Planar PL1900 - Manual - manualsarea.com

Page 5 - For Your Safety

3 TABLE OF CONTENTS For Your Safety For Your Safety --------------------------------------------------------------- 4 General Notes Special notes on LCD monitors ------------------------------------------ 6 Before You Operate The Monitor Features -----------------------------------------------------...

Page 6 - FCC Class B Radio Frequency Interference Statement

4 For Your Safety Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for...

Page 7 - PRECAUTIONS

5 PRECAUTIONS z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Us...

Page 8 - GENERAL NOTES; NOTES; You may find slightly uneven brightness on the screen depending

6 GENERAL NOTES SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker ...

Page 9 - BEFORE YOU OPERATE THE MONITOR; FEATURES; Register Your Planar Products Today

7 BEFORE YOU OPERATE THE MONITOR FEATURES • 48.0cm(19”) TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1280 X 1024 @60Hz • EPA ENERGY STAR ® • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following ...

Page 10 - Installation Instructions

8 Installation Instructions Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the AC...

Page 11 - Connecting the Signal Cable:

9 Installation Instructions CABLE CONNECTIONS Connecting the Signal Cable: the LCD monitor comes with a built-in signal cable. Plug the signal cable ′ s 15-pin connector into the computer's VGA port and tighten the two screws on the cable connector. Connecting the Power Cord: Plug the AC-power cord ...

Page 12 - ADJUSTING THE VIEWING ANGLE

10 Installation Instructions ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You are able to a...

Page 13 - OPERATING INSTRUCTIONS; GENERAL INSTRUCTIONS; The power cord should be connected.; EXTERNAL CONTROLS

11 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be co...

Page 15 - Figure 4 The OSD Message

13 OPERATING INSTRUCTIONS (cont.) HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window (Figure 4). 2. Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or a...

Page 16 - ADJUSTING THE PICTURE

14 OPERATING INSTRUCTIONS (cont.) ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Luminance Contrast Contrast from Digital-register. Brightness Backlight Adjustment. Image Setup Focus Adjust Picture Phase to reduc...

Page 20 - ERROR MESSAGE & POSSIBLE SOLUTION; CABLE NOT CONNECTED :; Check that the signal-cable is properly connected. If the

18 TECHNICAL SUPPORT (FAQ) (cont.) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. With a wrong phase ad...

Page 21 - APPENDIX; SPECIFICATIONS

19 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 48.0cm(19") Pixel pitch 0.294mm( H ) × 0.294mm( V ) Video R,G,B Analog Interface Input Separate Sync. H/V TTL H-Frequency 30kHz – 83kHz (Analog) V-Frequency 55-75Hz (Analog) Display Colors 16.7M Colors Dot Clock 135MHz (Analo...

Page 23 - Preset Display Modes

21 APPENDIX (cont.) Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY Dos-mode 720 × 400 31.469kHz 70.0Hz VGA 640 × 480 31.470kHz 60.0Hz 640 × 480 37.500kHz 75.0Hz SVGA 800 × 600 37.879kHz 60.0Hz 800 × 600 46.875kHz 75.0Hz XGA 1024 × 768 48.363kHz 60.0Hz 1024 × 768 56....

Page 24 - CONNECTOR PIN ASSIGNMENT

22 APPENDIX (cont.) CONNECTOR PIN ASSIGNMENT 1 5 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Ground 3. Blue 11. Ground 4. Ground 12. DDC-Serial Data 5. Detect Cable 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Cloc...

Planar PL1900 - Manual

Table of Contents:

Summary

Other Planar Models