Page 3 - iii; Contents; iv
iii Contents Product Information iv About the Display 1 Installing the Display 5 Appendix 10 Index 19 Regulatory Compliance 20 Standard Warranty 25
Page 4 - Product Information; Degree of Protection Against Electric Shock: No applied part.
iv | Dome E2c Display Product Information The design of the Dome E2c digital display takes into account every known measure to ensure your personal safety. Improper use of the display can result in electric shock, fire, or damage to the display. Read all instructions before setting up the display. C...
Page 5 - Symbol explanations; CAUTION
Product Information | v Symbol explanations Intended use The Dome E2c display is an AMLCD display designed for viewing medical X-ray images. This unit should not be used near patients and should be kept outside of 1.83 m perimeter and 2.29 m vertical. This device must not be used in primary image di...
Page 6 - Safety precautions; Safety requirements for medical electrical systems.; Safety tips; • In locations where 240V outlets are used, connect the Dome E2c
vi | Dome E2c Display Safety precautions External equipment intended for connection to signal input, signal output, or other connectors, must comply with the relevant IEC standard (EN/IEC 60601-1 series for medical electrical equipment). In addition, all such combinations (systems) must comply with ...
Page 7 - Unpacking and handling tips
Product Information | vii Unpacking and handling tips The Dome E2c display is a precision instrument that requires proper care to maintain product operation and adherence to specification. Unpack the display and components carefully, then set up and handle the unit properly to avoid damage to the LC...
Page 8 - Cleaning the display; prevent damage to the display case and the screen.; WARNING
viii | Dome E2c Display Cleaning the display Observe the following guidelines to maintain the display and the LCD screen. • Use a clean, lint-free, absorbent cotton cloth to clear off any residual glue from removal of the protective film or to remove surface dust. Apply light pressure to remove the ...
Page 9 - Shipping/storing the display; Before returning the display to the container, do the following:; Disposal information
Product Information | ix Shipping/storing the display Keep the display in its shipping container until installation. Return the display to its original container whenever you need to store the unit, move it to another location, or return it for repair. The packaging supplied by the manufacturer prot...
Page 11 - About the Display; Dome CXtra User’s Guide; System Requirements
About the Display The Dome E2c display system offers a 541-mm (21.3-in) color UXGA 1200x1600 AMLCD unit with a luminance output of 500 nits minimum. The display connects directly to a controller board via a Digital Visual Interface 1.0 interface. With AMLCD modules delivering 2-megapixel resolutions...
Page 12 - Display Components; Legend; Reset. Restores the display configuration to default.
2 | Dome E2c Display Display Components Review this illustration of the back panel to identify controls and ports on the display unit. Legend 1 Reset. Restores the display configuration to default. 2 LED. Shows display status. 3 DIN 8-pin connector. Drives power to the display. 4 S-Video, separate v...
Page 13 - Display Positions; Tilt range
About the Display | 3 Display Positions You can adjust the tilt, height, viewing angle, and orientation of the display to maintain an ergonomic and comfortable viewing position. Make sure that your eyes are level with the top of the display cabinet so that you look downward to read the screen conten...
Page 14 - Desk Stand Features; Stand height lock
4 | Dome E2c Display Desk Stand Features Unfasten the stand lock to adjust display height. Remove the stand cover to thread the power cord and DVI cable connections to the display. To activate the USB hub function, the display must be connected to a USB-compliant computer or another hub with a USB c...
Page 15 - Installing the Display; Warning; bag to prevent electrostatic discharge.; Tips; • Access to ports. For displays mounted on a desk stand, rotate the LCD
Installing the Display | 5 Installing the Display Before you install the display controller, remove any existing graphics card and its driver from your system. Also disable any onboard graphics capability on the motherboard. Warning • In locations where 240V outlets are used, connect the Dome E2c di...
Page 16 - Install the Display Controller; To install the display controller; Remove the computer cover and then the blank bracket from
6 | Dome E2c Display Install the Display Controller Before you install the display controller, make sure your display system will be set up in a well-ventilated location with an adequate amount of space. Excessive heat cannot dissipate when display vents are blocked. Turn off your computer and perip...
Page 17 - Connect the Video and Power Cables; To connect the cables
Installing the Display | 7 Connect the Video and Power Cables Use only the power adapter (Ault MW122KA1223F52), power cord, and the video cable shipped with the Dome E2c display. To connect the cables 1 Plug one end of the DVI cable into the DVI port on the connector plate. Secure the connection. 2 ...
Page 18 - Install the Display Driver; To install the driver
8 | Dome E2c Display Install the Display Driver Upon restarting your computer system, you must log on with administrator privileges. On Windows 2000 systems, Service Pack 4 or higher must be installed. To install the driver 1 Start the system. Click Cancel on the Found New Hardware Wizard. Click No ...
Page 19 - Adjust Display Properties; To set the display orientation
Installing the Display | 9 Adjust Display Properties Use the Display Properties dialog to make changes to the video settings or to set up a dual-display configuration. To set the display orientation 1 Right-click the desktop and select Properties > Settings. 2 Select the monitor that you want to ...
Page 20 - Appendix
10 | Dome E2c Display Appendix Troubleshooting Specification Video Modes Video Timing Connector Ports LED Status Lights Component Removal Power Management
Page 21 - Troubleshooting; Problem
Troubleshooting | 11 Troubleshooting Problem Possible Cause Solution No image appears on the screen Computer is not powered on. Turn on computer. Power cord is not securely connected. Tighten power cord connection and turn on computer. Video cable connected incorrectly. Make sure the first display o...
Page 22 - Specification; Category
12 | Dome E2c Display Specification In locations where 240V outlets are used, connect the Dome E2c display only to a center-tapped, 240V, single-phase supply (only for Canada and the United States). Category Characteristic Item Specification Screen Screen size diagonal 541 mm (21.3 in.) Native resol...
Page 23 - Power Supply
Specification | 13 Power Supply CAUTION: Use only the power adapter supplied with the Dome E2c display unit; Ault MW122KA1223F52. Reliability Environment Category Characteristic Item Specification Power input requirements Voltage selection Auto-ranging Voltage 100 – 240V AC Current 2.0 A Frequency 5...
Page 24 - Video Modes; Dome E2c
14 | Dome E2c Display Video Modes Resolutions expressed in pixels (W x H). Single desktop requires dual displays. Video Timing Display Resolution Orientation Palette Bits per pixel Dome E2c 1200 x 16001600 x 1200 PortraitLandscape True color 32 Standard Resolution Vertical Refresh (Hz) Horizontal Sc...
Page 25 - Connector Ports; Input power port on connector plate
Connector Ports | 15 Connector Ports The video signal connector is a standard DVI connector, driving data to the display. Diagnosis requiring DICOM calibration with the Dome CXtra software can only be supported on the DVI-D interface. The Dome E2c display use an 8-pin DIN connector. The power input ...
Page 26 - LED Indication Lights
16 | Dome E2c Display LED Indication Lights The LED indicator on the connector plate provides information on the display status. Reset (left) and LED on connector plate LED Indication Description Solid green Operating with signals Flashing green Operating without signals Solid yellow Fault condition...
Page 27 - Display Driver Removal; To remove the driver; Close all applications that are running.
Display Driver Removal | 17 Display Driver Removal Follow the appropriate procedure below to remove the driver from your system. To remove the driver 1 Close all applications that are running. 2 Navigate to the Control Panel and select Add/Remove Programs. 3 Select your current graphics card drivers...
Page 28 - Power Management; • Dome CXtra Backlight Saver service (preferred)
18 | Dome E2c Display Power Management You have two ways to lower energy usage when the Dome E2c display is idle: • Dome CXtra Backlight Saver service (preferred) • Screen Saver (set via Windows operating system) Activate the power saver when you anticipate periods of inactivity, such as at the end ...
Page 29 - Index
19 Index B brightness, display 9 C cleaning viii configuration, dual setup 9 connecting DVI cable 7 power cord 7 connector port 15 contents, package x D desk stand 4 DIN connector 15 display about 1 brightness 9 components 2 controller, installing 6 install 5 orientation 9 positions 3 properties, ch...
Page 30 - Regulatory Compliance
Regulatory Compliance Canada, European Union, United States This display has been tested and found to comply with IEC/EN 60601-1 and IEC/EN 60601-1-2 standards, and is certified to meet medical standard C22.2 No. 601.1-M1990 (C US Mark). The medical display, in addition to meeting medical requiremen...
Page 32 - EU Declaration of Conformity for Medical Application
EU Declaration of Conformity for Medical Application A Declaration of Conformity has been filed for this product. For additional copies of the Declaration of Conformity document, contact Planar Systems. The Dome EX digital flat-panel display meets the essential health and safety requirements, is in ...
Page 34 - CCC
Australian China Japan Korea C-Tick Australian Communications Authority regulating product EMC compliance. CCC China Compulsory Certification regulating safety and EMC. GB4943-2001 GB9254-1998 (Class A) CB17625.1-2003 VCCI Voluntary Control Council for Interference by information technology equipmen...
Page 35 - Standard Warranty; Summary; • Standard 1-year “repair and return” warranty; Standard Warranty Return Procedure; Contact Planar via the web at
Standard Warranty Summary • Standard 1-year “repair and return” warranty • A 2-year backlight warranty on color displays * • Typical repair turnaround time of 10 business days Standard Warranty Return Procedure As a Planar Standard Warranty customer, you must follow the procedure below if you have a...
Page 37 - Exclusion of Damages; DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE; Effect of Local Law
Exclusion of Damages THE LIABILITY OF PLANAR IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. PLANAR SHALL NOT BE LIABLE FOR THE FOLLOWING: 1 DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS...
