Petsafe Dog Kennel Manual - Free PDF Download

Page 1 - Assembly Instructions and Multilingual Support

Assembly instructions for the Do-It-Yourself Dog Kennel, including a warning to read the guide before starting, and visual representation of the assembled kennel.

Page 2 - Manual Table of Contents and Support Information

Table of contents outlining assembly steps, component details, installation procedures, warranty registration instructions, and customer support contact information.

Page 3 - Required Components and Tools for Assembly

List of components required for assembling a pet gate, including bent tubing, chain link fabric, hinges, bolts, and tie wire, along with necessary tools such as a hammer, adjustable wrench, pliers, and tape measure.

Page 4 - Assembling the Base Frame Structure

Instructions for assembling the bottom frame by connecting corner and frame rails using swedged ends, and attaching uprights with clamps and carriage bolts, illustrated with diagrams.

Page 5 - Assembling Gate Uprights and Rails

Instructions for adding an upright post and top rails to the gate structure, detailing how to connect components while ensuring posts are straight and nuts are tight, avoiding joint spans.

Page 6 - Installing Gate Components and Hinges

Procedure for assembling and installing a gate, including attaching chain link fabric using tension rods and clips, installing hinges, positioning the gate, and securing the latch.

Page 7 - Attaching Fence Fabric to Pet Enclosure

Steps for attaching chain link fabric to a pet enclosure, detailing how to clip the fabric, secure it with a tension rod, and use tie wires for support.

Page 8 - Installing Chain-Link Fence Sections

Instructions for installing a chain-link fence by stretching the fabric between posts and then cutting and securing the final section using tension rods and clips.

Page 9 - Securing Pet Containment Fabric and Legal Terms

Instructions for securing pet containment fabric, including attachment points, safety warnings regarding pet training, and legal terms of use and liability limitations.

Page 10 - Multilingual Introduction and Warranty Information

Introduction and table of contents in a secondary language, customer service contact details, product registration for warranty benefits, and manual section numbering.

Page 11 - Component List and Tools for Assembly

Detailed list of parts required for assembling the product, including bent tubes, mesh, hinges, bolts, and metal fasteners, alongside essential tools like a hammer, wrench, pliers, and measuring tape.

Page 12 - Assembling the Lower Frame Structure

Step-by-step instructions for assembling the base frame by connecting curved and straight tubes, and adding vertical tubes to corners and midpoints using brackets and bolts.

Page 13 - Assembling Pet Enclosure Structure

Instructions for assembling a pet enclosure, detailing how to add a vertical tube for the door and upper tubes, including required parts, assembly directions, and safety notes regarding structural weak points.

Page 14 - Assembling and Installing the Gate Assembly

Procedure for assembling the gate using tubes, tension triangles, mesh, and metal brackets, detailing steps for attaching components (5A–5F) and installing hinges and latches.

Page 15 - Installing Mesh Fencing for Pet Enclosure

Instructions for installing the mesh fencing by attaching the mesh to the frame using tension bars and metal fasteners, including safety advice regarding the weight of the mesh roll.

Page 16 - Securing Chain-Link Fence Sections

Instructions for installing chain-link fence sections, detailing how to tension the fence between posts and then cut and secure the final section with tension springs and staples.

Page 17 - Attaching Metal Grid and Liability Disclaimer

Instructions for attaching a metal grid to a pet enclosure (Step 10), safety warnings about enclosure limitations, and liability conditions from Radio Systems Corporation.

Page 18 - Spanish Introduction and Warranty Information

Introduction and table of contents in a secondary language, customer service contact details, warranty registration for full coverage, and overview of assembly steps.

Page 19 - Included Parts and Tools for Assembly

List of included components such as corner rails, tension bars, hinges, bolts, and wire mesh, along with the necessary tools: hammer, adjustable wrench, pliers, and measuring tape.

Page 20 - Assembling the Lower Frame Structure

Step-by-step instructions for assembling the lower frame by connecting mitered and straight rails to form the base, and attaching vertical tubes at corners and midpoints using brackets and bolts.

Page 21 - Assembling Pet Enclosure Doors and Structure

Instructions for assembling a pet enclosure, detailing how to add the door tube (Step 3) and upper structure (Step 4), focusing on correct placement of components and tightening all bolts.

Page 22 - Assembling and Installing Gate Door

Procedure for assembling and installing a gate door, detailing how to assemble the door frame using rails, tension bars, wire mesh, and hooks (5A–5F), and installing hinges and the latch.

Page 23 - Attaching Wire Mesh Enclosure

Instructions for installing a wire mesh enclosure (Step 7), detailing how to attach the mesh to vertical rails using tension bars and hooks, with close-up diagrams of connection points.

Page 24 - Installing Chain-Link Fence Sections

Instructions for installing chain-link fence sections, detailing how to stretch the mesh and then cut and secure it with tension bars and hooks, accompanied by diagrams.

Page 25 - Securing Wire Mesh Gate and Legal Disclaimer

Instructions for securing a wire mesh gate (Step 10), including diagrams for attaching wires at the top and bottom, pet safety warnings, and legal disclaimer regarding product use and liability.