Page 2 - IMPORTANT; This manual should be read carefully before the; CONTENTS
2 IMPORTANT This manual should be read carefully before the icemaker is installed and operated. Only qualified service technicians should install, service, and maintain the icemaker. Read the warnings contained in this booklet carefully as they give important information regarding safety. Please ret...
Page 3 - Indicates a situation which could result in damage to the unit.; THIS APPLIANCE MUST BE GROUNDED:; This unit is equipped with a
3 Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury. CAUTION Indicates a situation which c...
Page 5 - PERLICK ICE MAKER; MOTOR-COMPRESSOR THERMALLY PROTECTED
5 PERLICK ICE MAKER MODEL NUMBER H50IMS-R SERIAL NUMBER AC SUPPLY VOLTAGE 115-120/60/1 AMPERES 3.4 AMPS DESIGN PRESSURE HI-240PSI LO-120PSI REFRIGERANT 134a 4.2 oz. B. Nameplate Rating See the nameplate for electrical and refrigeration specifications. This nameplate is located inside the bin on the ...
Page 10 - Ensure all components, fasteners, and thumbscrews; A. Checks Before Installation; it will not work properly.; CAUTION; For best operating results:
10 II. Installation and Operating Instructions WARNING 1. This icemaker must be installed in accordance with applicable national, state, and local regulations. 2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fall...
Page 11 - equipment or where the icemaker cannot be pulled out for service.; Installation Space; Between Two Cabinets
11 2. Built-In Installation Site CAUTION 1. Do not let the weight of the counter rest on the icemaker.2. Do not install the icemaker in a corner where the door will interfere with other equipment or where the icemaker cannot be pulled out for service. Installation Space Model Height Width Depth H50I...
Page 12 - Overlay Panel Parts
12 1 2 3 4 6 5 C. Door Overlay Panel Fabrication and Attachment (H50IMW, H50IMW-AD) IMPORTANT The overlay panel must be crafted by a professional cabinet maker to ensure quality results. (1) Parts Ensure that all parts required for the overlay panel assembly are contained in the accessories bag. Ove...
Page 13 - H50IMW Overlay Panel Specification; Overlay Panel Height
13 (2) Overlay Panel Specification Use the specification that applies to your icemaker (H50IMW or H50IMW-AD) and the directions that follow to prepare your overlay panel. (a) H50IMW H50IMW Overlay Panel Specification Overlay Panel Height 29 17/32" (750 mm) Overlay Panel Width 14 13/16" (376 ...
Page 14 - H50IMW-AD Overlay Panel Specification
14 H50IMW-AD Overlay Panel Specification Overlay Panel Height 27 9/16" (700 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb. (9 kg) maximum (b) H50IMW-AD
Page 16 - ) If you would like to reverse the door hinges, do the following:
16 Screws f) Remove hinge (C1) from the top right part of the door, flip it and reattach to the bottom left. Remove hinge (C2) from the bottom right part of the door, flip it and reattach to the top left. See Fig. 8. Proceed to step 7. d) Remove hinge (B) from the right side of the unit and the 2 fi...
Page 18 - securing the sheet metal bracket to the overlay panel. See Fig. 16.
18 Snug the screws, but do not tighten. Sheet Metal Bracket Overlay Panel Tighten the screws. 5) Fasten the overlay panel to the door using the four M4×25 pan head screws provided. Snug the screws, but do not tighten. See Fig. 17. 6) Fasten the sheet metal bracket to the bottom of the door with the ...
Page 21 - Contact your local Perlick distributor for recommendations.
21 F. Water Supply and Drain Connections WARNING 1. Water supply and drain connections must be installed in accordance with applicable national, state, and local regulations. 2. Normal operating water temperature should be within 45°F to 95°F (7°C to 35°C). Operation of the icemaker, for extended pe...
Page 22 - WARNING; Ensure all components, fasteners, and thumbscrews are
22 G. Final Checklist WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. 1) Is the icemaker level?2) Is the icemaker in a site where the ambient temperature is within 45°F to 100°F ...
Page 23 - icemaker to prevent damage to the compressor.
23 H. Startup WARNING 1. All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty coverage. 2. If the icemaker is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 3. At start...
Page 24 - A. Cleaning and Sanitizing Instructions; ammonia type cleaners.; Cleaning Procedure; ) Remove all ice from the evaporator and the storage bin.
24 III. Cleaning and Maintenance WARNING 1. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any cleaning or maintenance is done to the unit. Make sure that none have fallen into the storage bin. 2. The storage bin is for ice use only. Do not store anythi...
Page 26 - Sanitizing Solution; Sanitizing Procedure
26 3. Sanitizing Solution IMPORTANT For safety and maximum effectiveness, use the solution immediately after dilution. Dilute 0.5 fl. oz. (14.8 ml or 1 tbs) of a 5.25% sodium hypochlorite solution (chlorine bleach) with 1 gallon (3.8 l) of warm water. This is a minimum amount. Make more solution if ...
Page 27 - chute down until it clicks onto both frame pipes. See Fig. 36.
27 Reducing Pipe Rail Rail 13) Position and lock the ice chute onto the front and rear frame pipes by pushing the ice chute down until it clicks onto both frame pipes. See Fig. 36. 14) Slide in the water tank along the rails at the bottom of the left and right brackets until it locks into place. See...
Page 29 - Stainless Steel Exterior; electrical outlet before cleaning the condenser.
29 B. Maintenance IMPORTANT This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 1. Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use a damp cloth containing a neutral cl...
Page 30 - Rinse thoroughly after cleaning.
30 C. Preparing the Icemaker for Long Storage CAUTION When storing the icemaker for an extended time or in sub-freezing temperatures, follow the instructions below to prevent damage. When the icemaker is not used for two or three days under normal conditions, it is sufficient to move the control swi...