Page 2 - CONTENTS; Section
2 Pelco Manual C1487M-D (7/99) CONTENTS Section Page GENERAL .......................................................................................................................... 4 IMPORTANT SAFEGUARDS AND WARNINGS ....................................................... 4IN-CEILING MODELS ........
Page 4 - GENERAL; IMPORTANT SAFEGUARDS AND WARNINGS; Only use replacement parts recommended by Pelco.; MEASURES DE SECURITE IMPORTANTES
4 Pelco Manual C1487M-D (7/99) GENERAL IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel andconform to all local codes. 2. Unless the unit is spe...
Page 5 - COMPASS TOOL; Figure 2. Back Box Parts; Back Box
Pelco Manual C1487M-D (7/99) 5 COMPASS TOOL SAFETYBRACKET CONDUIT FITTING& LOCK NUT T-RAIL CLIP Figure 2. Back Box Parts Figure 1. In-Ceiling Components BACKBOX DOMEDRIVE LOWERDOME IN-CEILING MODELS The Spectra II™ dome and Spectra Lite™ dome shipping cartons contain three boxes, plusthe C1487M-...
Page 6 - Figure 3. Pendant Components; PENDANT MODELS; Back box; Dome Drive; Dome drive; Lower Dome; Acrylic lower dome with trim ring
6 Pelco Manual C1487M-D (7/99) BACKBOX DOMEDRIVE LOWERDOME Figure 3. Pendant Components PENDANT MODELS The Spectra II™ dome and Spectra Lite™ dome shipping cartons contain three boxes, plusthe C1487M-D system manual that covers everything in the system (back box, dome drive,and lower dome). Inspect ...
Page 7 - DESCRIPTION; MODELS
Pelco Manual C1487M-D (7/99) 7 DESCRIPTION Spectra II™ and Spectra Lite™ domes are capable of the following: • 360 ° pan rotation • preset positioning • +2 to -92 ° tilt • variable speed The in-ceiling models can be installed in hard ceilings or standard 2' x 2' (61 cm x 61 cm)suspended ceilings. Th...
Page 8 - INSTALLATION FOR IN-CEILING MODELS; CEILING AND BACK BOX PREPARATION; Use the SCA1; Figure 4. Compass Tool
8 Pelco Manual C1487M-D (7/99) SPECTRA LITE™ PENDANT COMPONENTS BB5T-PB Black pendant-mount back box (CE, UL, cUL) BB5T-PG Light gray pendant-mount back box (CE, UL, cUL) BB5T-PG-E Same as BB5T-PG except includes heater and sun shield (CE, UL, cUL) DD5TAC Dome drive with color camera and lens, NTSC ...
Page 9 - SUSPENDED CEILING; Locate the center point to drill a hole in the tile.; The; Figure 6. Installing Back Box
Pelco Manual C1487M-D (7/99) 9 SUSPENDED CEILING 1. Remove the ceiling tile from the ceiling. (The ceiling tile cannot be thinner than 0.50inch [1.27 cm] nor thicker than 1.75 inches [4.45 cm].) 2. Locate the center point to drill a hole in the tile. 3. Drill a hole in the ceiling tile using a 3/32-...
Page 10 - WIRING; Refer to Table A for the type of video coaxial cable to use.; Figure 8. Wiring Diagram for Spectra IITM; The dome will stop
10 Pelco Manual C1487M-D (7/99) WIRING Bring wiring to the back box opening in the ceiling. Do not attach the wiring to the back box.You will do that later. Refer to Figure 8 for the Spectra II™ wiring diagram or Figure 9 for the Spectra Lite™wiring diagram. Wiring is required for power, earth groun...
Page 11 - Figure 9. Wiring Diagram for Spectra LiteTM; are; Table A. Video Coaxial Cable Wiring Distances; Maximum Distance
Pelco Manual C1487M-D (7/99) 11 Figure 9. Wiring Diagram for Spectra Lite™ CONTROL (RS-422) SPECTRA LITE™ INTERCONNECT BOARD If you are using a Coaxitron ® controller, the control signals to operate the dome drive will be transmitted over the video coax. The RS-422 control lines are not used. If you...
Page 12 - BACK BOX INSTALLATION; Install the ceiling; THUMBSCREW; Figure 10. Interconnect Door
12 Pelco Manual C1487M-D (7/99) Table B. 24 VAC Wiring Distances The following are the recommended maximum distances for 24 VAC with a 10-percentvoltage drop. (Ten percent is generally the maximum allowable voltage drop for AC-powereddevices.) Wire Gauge 20 18 16 14 12 10 30 vA 94 ft 150 ft 238 ft 3...
Page 13 - BACK BOX CONNECTIONS; Connect earth ground to the middle connector on the power; From controller; Figure 11. Transformer; Wiring; If each dome; POWER
Pelco Manual C1487M-D (7/99) 13 BACK BOX CONNECTIONS Refer to Figure 12 or 13 to attach the wiring to the interconnect circuit board inside the backbox. Also refer to Figure 8 or 9 if necessary. 1. Earth Ground - Connect earth ground to the middle connector on the power connector. 2. Power - Connect...
Page 14 - Connect only a low
14 Pelco Manual C1487M-D (7/99) Figure 13. Interconnect Circuit Board Electrical Connections for Spectra Lite™ HTR/FAN RX– RX+ TX– TX+ PWR IN FUSE 1.6 A DOME DRIVECONNECTOR RS-422CONTROLSIGNALS POWER (24 VAC ONLY) FAN 24 VACMIDDLEPIN ISGND VIDEO CONNECTORFOR OPTIONALTRANSLATORSUBASSEMBLY 5. Heater/F...
Page 15 - DOME DRIVE; Refer to Figure 14 and Tables D and E for the settings for SW2.; Make; Table C. Switch Settings for SW1; Control Type; Figure 14. Switch Locations
Pelco Manual C1487M-D (7/99) 15 DOME DRIVE 1. Turn on power to the back box. The red LED should light to indicate power. If the LED does not light, correct the trouble before proceeding. Refer to the Trouble- shooting section. If the light is operating, you may either leave the power on and continue...
Page 16 - Table D. Switch Settings for SW2 – P-Type Control; For Coaxitron; Receiver Address
16 Pelco Manual C1487M-D (7/99) Table D. Switch Settings for SW2 – P-Type Control NOTES: For Coaxitron ® controls, SW2 is not used; set all switches OFF. For D-type control systems, refer to Table E. Receiver Address Switch Setting SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 1 OFF OFF OFF OFF OFF 2 ON OFF OFF OFF...
Page 17 - Table E. Switch Settings for SW2 – D-Type Control
Pelco Manual C1487M-D (7/99) 17 Table E. Switch Settings for SW2 – D-Type Control NOTES: For Coaxitron ® controls, SW2 is not used; set all switches OFF. For P-type control systems, refer to Table D. Receiver Address Switch Setting SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 1 ON OFF OFF OFF OFF...
Page 21 - LOWER DOME
Pelco Manual C1487M-D (7/99) 21 Table E. Switch Settings for SW2 - D-Type Control (continued) 237 ON OFF ON ON OFF ON ON ON 238 OFF ON ON ON OFF ON ON ON 239 ON ON ON ON OFF ON ON ON 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON OFF OFF ON ON ON ON 243 ON ON OFF OFF ON ON...
Page 22 - INSTALLATION FOR PENDANT MODELS; PENDANT-MOUNT INSTALLATION; Bring the wiring for the dome through the mount. Refer to the; Figure 16. Lower Dome Installation, Pendant Models
22 Pelco Manual C1487M-D (7/99) INSTALLATION FOR PENDANT MODELS PENDANT-MOUNT INSTALLATION 1. Install the pendant dome mount. Refer to the instructions supplied with the mount. Ifthe mount is outdoors, make sure it is properly sealed to keep moisture out. 2. Bring the wiring for the dome through the...
Page 23 - SURFACE-MOUNT INSTALLATION; OPERATION
Pelco Manual C1487M-D (7/99) 23 10. If you are installing an outdoor model, plug the two-pin heater connection in the lower dome into the mating connector in the back box. 11. Remove the two screws and the tube of Loctite ® from the parts bag. Apply a drop of Loctite ® to each screw. 12. Push the lo...
Page 24 - Protocol C; control; PAN AND TILT FUNCTIONS; If the proportional pan mode is enabled (refer to the; AUTO FLIP; Auto Flip in the; SCAN SPEED
24 Pelco Manual C1487M-D (7/99) POWER-UP DISPLAY When the Spectra II™ dome or Spectra Lite™ dome is powered up or reset, the selectedprotocol, revision number, and other information is displayed on the monitor. For example,the screen might show the following information: PELCO SPECT II 4.0CONFIGURE ...
Page 25 - Zoom Wide; SPECTRA LITETM ZOOM; An asterisk denotes
Pelco Manual C1487M-D (7/99) 25 ZOOM SPECTRA II™ ZOOM The Spectra II™ dome can magnify an object up to 128 times. The dome has 16X of opticalzoom and 8X of electronic (digital) zoom for 128X total zoom. The amount of zoom can beset for 16X, 32X, 64X, or 128X. Software controls the amount of zoom. Re...
Page 26 - ZONES; PATTERNS; Spectra IITM only; Spectra IITM only
26 Pelco Manual C1487M-D (7/99) RANDOM, FRAME, AND AUTO SCANNING Program preset 97 (30) to start random scanning. Program preset 98 (31) to activate framescanning (three seconds of scanning followed by a three-second pause). Program preset99 (32) to start auto (continuous) scanning. Scan limit stops...
Page 27 - AUXILIARY OUTPUTS; PARK
Pelco Manual C1487M-D (7/99) 27 In certain situations, the dome will respond as follows: • If a preset has not been set, but an alarm is connected: the dome will go to a factorypreset that will not be the desired position. • If one alarm is a preset and another is a pattern and both are received: th...
Page 28 - PROGRAMMING THE SPECTRA IITM AND SPECTRA LITETM; Spectra LiteTM only
28 Pelco Manual C1487M-D (7/99) PROGRAMMING THE SPECTRA II™ AND SPECTRA LITE™ The Spectra II™ and Spectra Lite™ domes can be programmed for the following functions.( In this section, an asterisk denotes items that apply to Spectra II only. ) AGC (automatic gain control) Auto park time Power-up mode ...
Page 29 - Compensation
Pelco Manual C1487M-D (7/99) 29 MAIN MENU ACCESS You can call up the main menu on your monitor by programming (setting or creating) preset95 (28 if in 32-preset mode; refer to the Preset Functions section). Programming preset 95 for Pelco’s controllers varies according to the type of controller youa...
Page 30 - ZOOM LIMIT; RESET CAMERA; An asterisk
30 Pelco Manual C1487M-D (7/99) 3. Press the Iris Open button to enter the Camera submenu. 4. Move the joystick up or down to position the cursor beside Backlight Comp. 5. Press the Iris Open button on your keyboard. A star will appear beside Backlight Compand the cursor will move to the right besid...
Page 31 - AGC Mode
Pelco Manual C1487M-D (7/99) 31 Turning off power to the Spectra II™ and Spectra Lite™ domes does not reset the camera.Camera settings are retained in memory, and when the power is turned back on, thesettings will be the same as they were when it was turned off. To reset the camera: 1. Program prese...
Page 33 - SHUTTER SPEED
Pelco Manual C1487M-D (7/99) 33 PEAK - (Spectra II only) The cursor moves to a numeric value. Increasing this value will cause the auto iris circuit to react more to highlights or “peaks” in the picture. Decreas-ing this value will cause it to use the average video level to adjust the iris. Move the...
Page 34 - SHARPNESS
34 Pelco Manual C1487M-D (7/99) AUTO-FOCUS MODE There are two auto-focus modes: auto and off. If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will placethe focus in the manual mode. The dome will return to auto focus if you pan or tilt the unitor do a zoom function. If...
Page 35 - AUTO WHITE BALANCE -; LINE SYNCHRONIZATION
Pelco Manual C1487M-D (7/99) 35 AUTO SHARPNESS - (Spectra II only) The cursor moves to one of two choices: On or Off. Move the joystick up or down to toggle between them. Press the Iris Open button toselect the choice, or press the Iris Close button if you do not want to change the setting. SHARPNES...
Page 36 - An asterisk denotes items that apply to the
36 Pelco Manual C1487M-D (7/99) To change the line synchronization settings: 1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear. 2. If the cursor (>) is not beside Line Sy...
Page 37 - AUX MODE; ALARM RESUME
Pelco Manual C1487M-D (7/99) 37 To select the power-up mode: 1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear. 2. If the cursor (>) is not beside Power Up Mode, move the...
Page 38 - ALARM DWELL; ALARM PRIORITY
38 Pelco Manual C1487M-D (7/99) 5. Press the Iris Open button. The cursor will move to the right beside the word On or Off. 6. Move the joystick up or down to toggle between On or Off. 7. SELECT - Press the Iris Open button on your keyboard to select your choice.CANCEL - Press the Iris Close button ...
Page 39 - ALARM PATTERN; ZONE BLANK
Pelco Manual C1487M-D (7/99) 39 ALARM PATTERN (This section applies to Spectra II™ only .) In response to an alarm, the Spectra II™ dome can do either one full pattern (1.5, 3, or 6minutes long) or two half patterns (.75, 1.5, or 3 minutes long). You can choose one of thefollowing for each of the se...
Page 41 - MANUAL LIMIT STOPS
Pelco Manual C1487M-D (7/99) 41 LIMIT STOPS There are two types of limit stops: Manual limit stopsScan limit stops When manual limit stops are set, a manual (joystick) pan operation will stop when a limitstop is reached. When scan limit stops are set, the dome will reverse direction during random, f...
Page 43 - TROUBLESHOOTING; The dome drive
Pelco Manual C1487M-D (7/99) 43 3. Press the Iris Open button to enter the submenu entitled Other. 4. Move the joystick up or down to position the cursor beside Pattern Length. 5. Press the Iris Open button. The cursor will move to the right beside the number ofminutes (1.5, 3, or 6). 6. Move the jo...
Page 45 - BACK BOX ELECTRONIC ASSEMBLY REMOVAL; To remove the back box electronic assembly:; MAINTENANCE; DOME CLEANING; Clean the same as the exterior surface.; SERVICE MANUAL
Pelco Manual C1487M-D (7/99) 45 BACK BOX ELECTRONIC ASSEMBLY REMOVAL To remove the back box electronic assembly: 1. Turn off power. 2. Open the interconnect door and disconnect all wiring to the back box. 3. Use an 11/32 socket driver to remove the three 8-32 washers and nuts that hold theelectronic...
Page 46 - SPECIFICATIONS; MECHANICAL
46 Pelco Manual C1487M-D (7/99) SPECIFICATIONS MECHANICAL Construction Back box: Aluminum Dome drive: Aluminum, ABS plastic Lower dome: Acrylic Cable Entry In-Ceiling: .75" (1.91 cm) conduit fitting Pendant: Through 1.5" (3.81 cm) NPT pendant mount Pan Movement: 360 ° Continuous pan rotation...
Page 47 - CAMERAS; Figure 18. SD5 Series Dimension Drawing
Pelco Manual C1487M-D (7/99) 47 Ratings: NEMA Type 1–In-ceiling back boxes, all dome drivesNEMA Type 4–Pendant back boxesIP 66–Pendant back boxes Weight Unit Shipping In-Ceiling Back Box: 2.6 lb (1.18 kg) 4 lb (1.81 kg) Dome Drive: 2.65 lb (1.20 kg) 5 lb (2.27 kg) Lower Dome: .19 lb (.09 kg) 1 lb (....
Page 49 - MONOCHROME
Pelco Manual C1487M-D (7/99) 49 MONOCHROME (Spectra II™ Only) Signal Format EIA (model DD5AM)CCIR (model DD5AM-X) Scanning System: 2:1 interlace Image Sensor 1/4-inch interline transfer CCD Horizontal Resolution: >500 TV lines Effective Pixels EIA: 768 (H) x 494 (V) CCIR: 752 (H) x 582 (V) Lens: ...
Page 50 - REVISION HISTORY; WARRANTY AND RETURN INFORMATION; REGULATORY NOTICES
50 Pelco Manual C1487M-D (7/99) REVISION HISTORY Manual # Date Comments C1487M 7/98 Original version. C1487M-A 11/98 Revised the manual to incorporate Spectra Lite™ material. Added material on CCIR and EIA monochrome cameras, and PAL color camera. Revised material in Section 5.11.21.2, Programming L...
