Paradyne 9550 DS3 - Manual

5 Installing in a Rack Two types of mounting screws are provided. Use: „ #10-32 mounting screws for rails with threaded screw holes „ #12-24 mounting screws and self-retaining nuts for rails with unthreaded screw holes Procedure To install the Probe in a rack: 1. Determine where in the rack you will...

6 3. Insert and tighten the screws in the top screw positions, then tighten the bottom screws. Connecting to Power The Probe requires a 120 VAC, 60 Hz power source. Procedure To connect the 9550 DS3 Probe to power: 1. Connect a ground wire to the grounding screw on the front of the Probe. 2. Connect...

8 Connecting the Subscriber Port The Subscriber port connects to your DTE, such as a router. Procedure To connect the Subscriber port: 1. If clearance at the front of the Probe is limited, attach right-angle BNC adapters to the ends of two BNC cables. 2. Take the end of the receive cable and push it...

9 Connecting to the DS3 Network The Network port connects to the packet network . Procedure To connect the Network port: 1. If clearance at the front of the Probe is limited, attach right-angle BNC adapters to the ends of two BNC cables. 2. Take the end of the receive cable and push it onto the NETW...

10 7. If the cable length is longer than 100 feet (30 meters), set the LBO on the T3 Network Interface Options configuration screen to Long. The default is Short. See the iMarc SLV Configuration Reference . Connecting the Ethernet Port The Ethernet port provides a 10/100BaseT connection that can be ...

11 Connecting the Modem Port The Probe supports asynchronous terminal interface sessions over its integral modem. Procedure To connect the Modem port: 1. Plug one end of an RJ11 telephone cable into the Modem port. 2. Plug the other end of the cable into an RJ11 telephone jack. 05-17705 Rx Tx Rx Tx ...

12 Connecting the Console Port The Console port can be used to connect a VT100-compatible terminal or a PC with terminal emulation software, providing direct access to the asynchronous terminal interface. Procedure To connect the Console port to a terminal or PC: 1. Press the 9-pin connector of a te...

13 Using the Asynchronous Terminal Interface The Probe should operate using the default (factory-set) configuration options, with exception to the changes specified in these installation instructions. Refer to the following table for help in navigating through the menus. Follow these steps to go to ...

14 Menu Hierarchy The Menu Hierarchy shows the organization of the Probe’s asynchronous terminal interface screens. Status System and Test Status Self-Test ResultsLast System ResetHealth and StatusTest Status IP Path Connection Status Device NameIP AddressStatusDiscovery Source PVC Connection Status...

15 Configuration System Class of Service DefinitionsMonitored Protocol DefinitionsService Level VerificationGeneral Network PhysicalATMVPI, VCI Records T3 User Ports PhysicalATMVPI, VCI Records PVC Connections Source and Destination Link, VPI, VCI, Management Type IP Subnet List Add and Display Loca...

16 Saving Configuration Options Procedure To save a configuration option change: 1. Press Ctrl-a to switch to the function keys area at the bottom of the screen. 2. Type s or S (Save) and press Enter. The Save Configuration To menu appears. 3. Press Enter again to save your changes to the Current Co...

17 EMI Notices United States – EMI Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a...

18 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and...