Paradyne 8414-A1-000 - Manual
Paradyne 8414-A1-000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – October; Product Documentation Online
- Page 3 – Installing the SCP Card; Procedure; SCP Card LEDs; Slot A
- Page 4 – Installing Two SCP Cards in the Same DSLAM; – The OC3 ports of the two SCP cards are connected to the same; Dual Link; – Automatic switching occurs in the event of failure, but the SCP; Load Sharing; – Both SCP cards are active, and connected to different uplink
- Page 5 – DS3 Uplink; and fasten them with cable ties.
- Page 6 – OC3 Uplink; Remove the plastic dustcover from the SFP socket.
- Page 7 – IMA Uplink; Assignments, on page 12; Cable Tie
- Page 8 – Type; or
- Page 9 – Using the Default Management Address; Setting the Management Address Using the CLI; To use the default management address:
- Page 10 – The management address can be set using the CLI.; To set the management address of the SCP card using the CLI:
- Page 11 – Using the Web Interface
- Page 12 – BNC Jacks; The following table; IMA Interface Pin Assignments; Table 2
- Page 13 – Data In; Function
- Page 15 – Equipment List; Table 4. Feature Numbers; Cards
- Page 16 – SCP Card Technical Specifications; Specifications
- Page 17 – Important Safety Instructions; OC3 Uplink Specifications
- Page 18 – Visit the Paradyne World Wide Web site at; Document Feedback; . Include the number and; Trademarks; Copyright
8400-A2-GZ40-10
October 2003
1
Hotwire
®
Shelf Concentration and Processing (SCP) Card
Installation Instructions
Document Number 8400-A2-GZ40-10
October 2003
Hotwire Shelf Concentration and Processing Card
A Hotwire
®
Shelf Concentration and Processing (SCP) card is a circuit card
assembly that comprises a parent card with an ATM switch, a backplane interface,
a processor, a cell multiplexer/demultiplexer, and an uplink childcard. The
childcard determines the type of ATM uplink supported by the SCP card.
When the SCP card is used in a Hotwire 8620 or 8820 GranDSLAM chassis, it
aggregates DSL traffic from each of the DSL port cards in the chassis on the
chassis’s backplane bus and concentrates it onto an ATM interface. The following
models are available:
The SCP card supports the following line cards:
8955 ReachDSL ATM Card
8965 ADSL ATM Card
8985 SHDSL ATM Card
With a Management Communications Controller (MCC) card installed in the same
chassis, the SCP card also supports Hotwire Time Division Multiplexer (TDM)
SDSL and SHDSL cards, Models 8775, 8777, 8779, and 8799.
SCP Card Model
ATM Uplink Childcard
8411-A1-000
DS3
8412-A1-000
OC3/STM1 Multimode Fiber
8413-A1-000
OC3/STM1 Single Mode Fiber Intermediate Reach (15 km)
8414-A1-000
OC3/STM1 Single Mode Fiber Long Reach (40 km)
8416-A1-000
8-Port DS1 IMA (Inverse Multiplexing over ATM)
8417-A1-000
8-Port E1 IMA
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 October 2003 8400-A2-GZ40-10 Product Documentation Online Complete documentation for this product is available at www.paradyne.com . Select Support → Technical Manuals → Hotwire DSL Systems. Select the following documents: 8400-A2-GB20 Hotwire Shelf Concentration and Processing (SCP) Card User’s G...
8400-A2-GZ40-10 October 2003 3 Installing the SCP Card SCP cards can be installed in: Slot A, Slot B, or both, of the 8820 GranDSLAM Slot A of the 8620 GranDSLAM Procedure To install the Hotwire SCP Card in a GranDSLAM chassis: 1. If there is a filler plate covering the slot, remove it. 2. Remov...
4 October 2003 8400-A2-GZ40-10 Installing Two SCP Cards in the Same DSLAM Two SCP cards may be installed in one DSLAM to provide redundancy or load sharing. There are three basic configurations for paired SCP cards: Y-Cable – The OC3 ports of the two SCP cards are connected to the same uplink devi...
