Paradyne 6310-A4 - Manual

5 Installing the Hotwire 6310 ReachDSL v1 Modem Place the ReachDSL modem on a flat surface with clearance for the rear connectors. Procedure 1. If a telephone is connected at the RJ11 wall jack where the modem will be installed, unplug the telephone line from the wall jack. 2. Connect a telephone to...

6 4. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable into the jack labeled ETHERNET. — Use a straight-through cable and connect the other end to an Ethernet hub. (To connect to a hub’s Uplink connection, use an Ethernet crossover cable). – or– — Use an Ethernet c...

7 5. Insert the supplied power cord’s round end into the jack labeled POWER. Plug the transformer into an AC outlet. The ReachDSL modem hardware installation is now complete. When the power cord is installed, the ReachDSL modem goes through a power-on self-test. PHONE LINE ETHERNET POWER 01-17010 Po...

8 Power-On When power is applied, the ReachDSL modem performs self-diagnostics and the PWR LED is on. The self-diagnostics includes a power-on self-test and all of the LEDs turn on for one second. Status LEDs All of the LEDs turn on and off during the power-on self-test. After a successful self-test...

9 Troubleshooting LED Symptom Action All LEDs are on. If LEDs remain on after ten minutes, the modem is not functional. Contact the service provider. ALM LED remains on. The power-on self-test may have failed. Unplug the unit and reapply power. If the alarm LED is still on, contact the service provi...

10 To improve data transmission throughput and minimize background noise during a telephone conversation, make sure that: „ The Hotwire 6310 ReachDSL v1 Modem is always powered on, even when not in use, and „ A Hotwire phone filter is installed on every telephone on the same line as the Hotwire 6310...

11 Cables & Connectors This section is reference information. Standard twisted-pair CAT3 or better cables are recommended. „ The LINE and PHONE interface connectors use 6-pin, non-keyed modular plugs. RJ11 or RJ14 6-pin connectors can be used. Line & Phone Connectors „ The LINE and PHONE jac...

12 „ The Ethernet interface connector uses an 8-pin, non-keyed modular plug. — To connect the ReachDSL modem to an Ethernet hub, use the straight-through connection. 8-Pin Straight-through Connection – or– — To connect the ReachDSL modem directly to a PC with an Ethernet NIC card, use an Ethernet cr...

13 Optional ReachDSL Modem Wall Placement The Hotwire 6310 ReachDSL v1 Modem is designed for tabletop placement. The ReachDSL modem can also be mounted on a wall. To mount the modem, you will need: ❑ Two slotted-head #6 self-threading screws with plastic anchors ❑ Drill and 3/16" drill bit for t...

14 ReachDSL Modem Hardware Template 5.10 01-17014 To p Bottom

15 Technical Specifications for Hotwire 6310 ReachDSL v1 Modem Item Specification* Height x Width x Depth 1.46 " x 5.72 " x 4.33 " (3.71 cm x 14.54 cm x 11.00 cm) Weight 0.45 lb. (0.20 kg) Power Class 2 Transformer normal service input voltage range Input: 100 VAC (+10%), 50 Hz; 120 VAC ...

16 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and...

18 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules. This compliance information statement pertains to the following products: Trade Name: Hotwire Model Number: 6310-A4-200 This device...

19 Government Requirements Certain governments require that instructions pertaining to connection to the telephone network be included in the installation and operation manual. Specific instructions are listed in the following sections. United States – Notice to Users of the Telephone Network 1. Thi...

20 8. This equipment cannot be used on public coin service provided by the telephone company. Connection to Party Line Service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information.) 9. An FCC compliant telephon...