Panasonic KX-PRW130 - Manual

For your safety To prevent severe injury and loss of life/property, read this section carefully beforeusing the product to ensure proper and safeoperation of your product. WARNING Power connection R Use only the power source marked on theproduct. R Do not overload power outlets andextension cords. T...

outlet is installed near the product and iseasily accessible. R This product is unable to make calls when:– the handset batteries need recharging or have failed. – there is a power failure. Battery R We recommend using the batteries notedon page 3. USE ONLY rechargeable Ni-MH batteries AAA (R03) siz...

R If the reception for a base unit location isnot satisfactory, move the base unit toanother location for better reception. Environment R Keep the product away from electrical noisegenerating devices, such as fluorescentlamps and motors. R The product should be kept free fromexcessive smoke, dust, h...

Setting up Connections n Base unit Connect the AC adaptor to the unit bypressing the plug firmly.Keep the plug in the horizontal positionand fasten the cord by hooking it.Connect the AC adaptor to the poweroutlet.Connect the telephone line cord to theunit, then to the single-line telephone jack(RJ11...

Battery charging Charge for about 7 hours. R Confirm “ Charging ” is displayed ( 1 ). R When the batteries are fully charged, “ Fully charged ” is displayed. 1 Note when setting up Note for connections R The AC adaptor must remain connected atall times. (It is normal for the adaptor to feelwarm duri...

Controls Handset A BC D E F GH I J Speaker MZN (SP-PHONE: Speakerphone) M N (TALK) Dial keypad ( * : TONE) ReceiverDisplay M FLASH NM CALL WAIT N M OFF N MicrophoneCharge contacts n Control type Soft keys By pressing a soft key, you can select thefeature shown directly above it on thedisplay. Naviga...

Item Meaning The line is in use. R When flashing slowly: Thecall is put on hold. R When flashing rapidly: Anincoming call is now beingreceived. Eco mode is on. (page 10) Noise reduction is set.(page 15) Z Speakerphone is on.(page 14)Answering system is on.(page 36)Ringer volume is off.(page 23)Silen...

6 M Save N a M OFF N Note: R When English is selected as the displaylanguage, 12-hour clock format is used.When Spanish is selected, 24-hour clockformat is used. Recording your greeting message You can record your own greeting messageinstead of using a pre-recorded greetingmessage. See page 36 for d...

Making calls 1 Lift the handset and dial the phonenumber. R To correct a digit, press M Clear N . 2 Press M N . 3 When you finish talking, press M OFF N or place the handset on the base unit orcharger. Using the speakerphone 1 Dial the phone number and press MZN . 2 When you finish talking, press M ...

Note: R After holding for 10 minutes, the call isdisconnected. Mute1 Press M Mute N during a call. 2 To return to the call, press M Mute N . Flash M FLASH N allows you to use the special features of your host PBX such as transferringan extension call, or accessing optionaltelephone services. Note: R...

To join the conversation, press M N when the other handset is on an outside call. Note: R A maximum of 3 parties (including 1 outsideparty) can join a conversation using 2extensions. (3-way conference) R To prevent other users from joining yourconversations with outside callers, turn thecall sharing...

Phonebook You can add 500 names (16 characters max.)and phone numbers (24 digits max.) to thephonebook, and assign each phonebook entryto the desired group. The total number of entries that can be storedvaries depending on how many phonenumbers you have stored for each entry.Total number of entries ...

2 MbN : Select the desired phone number. a M Detail N a M Save N 3 To store the name, continue from step 3,“Editing entries”, page 18. Storing caller information to thephonebook 1 MCN CID 2 MbN : Select the desired entry. a M Detail N R To edit the number: M Menu N a MbN : “ Edit ” a M Select N Pres...

Erasing entries Erasing an entry 1 Find the desired entry (page 18). a M Menu N 2 MbN : “ Erase ” a M Select N 3 MbN : “ Yes ” a M Select N a M OFF N Erasing all entries 1 MWN or MFN W a M Menu N 2 MbN : “ Erase all ” a M Select N 3 MbN : “ Yes ” a M Select N 4 MbN : “ Yes ” a M Select N a M OFF N N...

Menu list To access the features, there are 2 methods. n Scrolling through the display menus 1 M Menu N (right soft key) 2 Press MCN , MDN , MEN , or MFN to select the desired main menu. a M Select N 3 Press MCN or MDN to select the desired item from the next sub-menus. a M Select N 4 Press MCN or M...

*10 Wallpaper is displayed in the standby mode only when you select “ Digital(Small) ” or “ Off ” for this setting. *11 You can select to display either a single item or multiple items on one screen at a time for the handset main menu icons in function menu, recorded message list, phonebook list, ca...

n Weekly: MbN : Select the desired day of the week and press M Select N . a M OK N 5 Set the desired time. 6 * : Select “ AM ” or “ PM ” . a M OK N 7 Enter a text memo (30 characters max.). a M OK N 8 MbN : Select the desired alarm tone. a M Select N R We recommend selecting a differentringer tone f...

When a call is received, the unit rings for ashort time *1 while the caller is being identified. If the phone number matches an entry in thecall block list, the unit emits no sound to thecaller, and disconnects the call. (Caller IDsubscribers only)*1 This is called first ring. If you do not want the...

the phone number stored when it detectssound. Important: R You should perform a test run of the babymonitor procedure to ensure that the babymonitor feature is set correctly. Forexample, test its sensitivity. Check theconnection if you are diverting the babymonitor to an outside line. R This feature...

Editing an outside monitoring number 1 Press M Menu N on the handset being monitored. 2 MbN : “ On/Off ” a M Select N 3 MbN : “ On ” a M Select N 4 MbN : Select the outside line. a M Edit N 5 M Menu N a MbN : “ Edit ” a M Select N 6 Edit the name if necessary. a M OK N 7 Edit the phone number if nec...

memo can also be displayed for the schedulealarm. Important: R Make sure the unit’s date and time settingis correct (page 12). Adding a new entry 1 M Menu N (right soft key) a a M Select N 2 MbN : Select the desired date. a M Select N 3 M Menu N a MbN : “ Add new entry ” a M Select N 4 Edit the date...

Important: R The additional handset modelrecommended for use with this unit is notedon page 4. If another handset model isused, certain operations may not beavailable. Registering a handset to thebase unit The supplied handset and base unit arepre-registered. If for some reason the handsetis not reg...

Using Caller ID service Important: R This unit is Caller ID compatible. To useCaller ID features, you must subscribe to aCaller ID service. Contact your serviceprovider/telephone company for details. Caller ID features When an outside call is being received, thecaller information is displayed.Caller...

2 Press MCN to search from the most recent call, or press MDN to search from the oldest call. R You can see the detailed informationabout the caller by pressing M Detail N when in multiple display mode. 3 To call back, press M N . To exit, press M OFF N . Note: R If the entry has already been viewed...

Answering system The answering system can answer and recordcalls for you when you are unavailable toanswer the phone.You can also set the unit to play a greetingmessage but not to record caller messages byselecting “ Greeting only ” as the recording time setting (page 42). Important: R Make sure the...

Resetting to a pre-recorded greetingmessage If you want to use a pre-recorded greetingmessage once you record your own greetingmessage, you need to erase your owngreeting message. 1 M Menu N (right soft key) #304 2 M Yes N a M OFF N Playing back the greetingmessage1 M Menu N (right soft key) #303 2 ...

Advanced new message alerting features Audible message alert This feature allows the base unit to beep toinform you of a new message arrival whennew messages are recorded. The base unitbeeps 2 times every minute until you listen tothe messages, if the “ Base unit beep ” setting is turned on. The def...

call. This is so that unauthorized partiescannot listen to your messages. The defaultsetting is “ Inactivate ” . – “ Inactivate ” : You can listen to the message by pressing 4 to play new messages (without entering the remoteaccess code). – “ Activate ” : You must enter your remote access code and t...

Note: R If you do not press any dial keys within 10seconds after a voice guidance prompt, theunit disconnects your call. Remote commands You can press dial keys to access certainanswering system functions without waiting forthe voice guidance to prompt you. Key Operation 1 Repeat message(during play...

your service provider/telephone company,please contact your service provider/telephone company to deactivate yourvoice mail service.If your service provider/telephone companycannot do this:– Set this unit’s “ Ring count ” setting so that this unit’s answering systemanswers calls before the voice mai...

Smartphone integration You can install the free Smartphone Connectapp on your smartphone and use yoursmartphone as an extension of your phonesystem. The following features are availablewhen using the app.– Making and receiving calls using your landline – Making and receiving intercom calls– Playing ...

performing this procedure, and thenchange it back when finished. 3 MbN : Select your wireless router’s SSID. a M Select N 4 Confirm the SSID and then press M OK N . 5 Enter the password required to accessthe wireless network. a M OK N R After the base unit connects to thewireless router, “ Connected...

Other network features Wi-Fi repeater mode You can increase the signal range of yourwireless network by turning on the base unit’sWi-Fi repeater mode feature. 1 M Menu N (right soft key) #538 2 MbN : Select the desired setting. a M Save N Important: R If using Wi-Fi repeater mode, do not placethe ba...

Voice mail service Voice mail is an automatic answering serviceoffered by your service provider/telephonecompany. After you subscribe to this service,your service provider/telephone company’svoice mail system answers calls for you whenyou are unavailable to answer the phone orwhen your line is busy....

Note: R You can also use the M VM N soft key, if displayed, to play new voice mailmessages. R If the handset still indicates there are newmessages even after you have listened toall new messages, turn it off by pressingand holding # until the handset beeps. Error messages Display message Cause/solut...

Troubleshooting If you still have difficulties after following the instructions in this section, disconnect the base unit’sAC adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset,and then insert the batteries into the handset again. General use Problem Cause/solu...

Problem Cause/solution I cannot display thewallpaper. R Wallpaper is displayed in the standby mode only when youselect “ Digital(Small) ” or “ Off ” for the clock setting. Change the clock setting (page 24). I cannot register a handsetto a base unit. R The maximum number of handsets (6) is already r...

Problem Cause/solution The handset does not ring. R The ringer volume is turned off. Adjust ringer volume (page 14,23). R Silent mode is turned on. Turn it off (page 28). The base unit does notring. R The ringer volume is turned off. Adjust ringer volume (page 14). I cannot make a call. R The dialin...

Problem Cause/solution The 2nd caller’sinformation is notdisplayed during anoutside call. R In order to use Caller ID, call waiting, or Call Waiting Caller ID(CWID), you must first contact your service provider/telephonecompany and subscribe to the desired service.After subscribing, you may need to ...

Liquid damage Problem Cause/solution Liquid or other form ofmoisture has entered thehandset/base unit. R Disconnect the AC adaptor and telephone line cord from thebase unit. Remove the batteries from the handset and leave todry for at least 3 days. After the handset/base unit arecompletely dry, reco...

Network connection troubleshooting Problem Cause/solution I am having troubleconnecting. R Your wireless router is not turned or is not functioning. Refer tothe operating instructions included with your wireless router. R Your smartphone is not connected to your wireless router.Check your smartphone...

FCC and other information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:ACJ----------.If requested, this number must be provided ...

Guía Rápida Española Conexiones Instalación y carga de la batería Cargue aproximadamente durante 7 horas. Nota: L UTILICE SOLO baterías recargables de Ni-MH tamaño AAA (R03) ( ). L NO utilice baterías Alcalinas, de Manganeso o de Ni-Cd. L Confirme que las polaridades estén correctas ( S , T ). L Cam...

Sugerencias de operación Teclas de función Al oprimir una tecla de función, puede seleccionar la función que aparece directamente encima de ella en la pantalla. Preste atención a la pantalla para ver qué funciones están asignadas a las teclas de función durante la operación. Tecla navegadora − {^} ,...

Operaciones básicas Cómo hacer y contestar llamadas (Auricular) Para hacer llamadas Marque el número telefónico. s {C} / {s} Para contestar llamadas {C} / {s} Para colgar { OFF } Para ajustar el volumen del receptor o del altavoz Oprima {^} o {V} repetidamente mientras habla. Cómo hacer una llamada ...

Preguntas frecuentes Pregunta Causa y solución ¿Por qué aparece _ ? L El auricular está demasiado lejos de la unidad base. Acérquelo. L El adaptador para corriente de la unidad base no está conectado correctamente. Conecte de nuevo el adaptador para corriente a la unidad base. L El auricular no está...

Customer services Customer Services Directory (United States and Puerto Rico) Obtain Product Information and Operating Assistance; locate your nearest Dealer or Service Center; purchase Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at: http://www.pa...

Warranty (For United States and Puerto Rico) Limited Warranty Coverage If your product does not work properly because of a defect in materials or workmanship, Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, whic...

Limited Warranty Limits And Exclusions This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by produ...

Index # 3-way conference: 16 A Additional handsets: 32 Alarm: 27 Answering calls: 14 Answering system: 36 Call screening: 41 Erasing messages: 37 , 38 , 41 Greeting message: 36 Greeting only: 42 Listening to messages: 37 , 40 Message list: 37 New message alerting: 39 Number of rings: 41 Recording ti...

66 Notes PRW130USA(en)_0311_ver110.pdf 66 2014/03/11 12:59:00

1 Reconnect AC adaptor to the base unit. 2 Check if telephone line cord is connected. 3 Use rechargeable Ni-MH batteries. (Alkaline/Manganese/Ni-Cd batteries CANNOT be used.) 4 Read troubleshooting page in the Operating Instructions . If your product is not working properly. . . IMPORTANT! Visit our...