Page 2 - Safety precautions; CAUTION
indicates safety information. This class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. For CANADA Safety precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT...
Page 3 - indicates safety information.; IMPORTANT SAFETY INSTRUCTIONS
indicates safety information. 1) Read these instructions. ) Keep these instructions. ) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instruc...
Page 4 - Contents
4 Contents Safety precautions ................................................................................................................................................ 2 Operating precautions ........................................................................................................
Page 7 - Parts and their function
Page 9 - Rotary head connector panel; Note
9 Parts and their function Rotary head connector panel ND/EXT connector [ND/EXT] This is for the control of the ND filter and lens extender of the motorized lens unit.Connect this connector when using a motorized lens unit with ND filter and lens extender functions. The cable described in “Cable s...
Page 10 - Pedestal connector panel
10 Parts and their function Pedestal connector panel CONTROL IN RP connector [RP] This is the connector for the control of signals of the camera and pan-tilt head.It is connected to the TO PAN/TILT HEAD connector on the AW-RP655 multi-function controller and AW-RP555 multi hybrid control panel.Use...
Page 11 - Installation; For a stand-alone installation; Assembling the pan-tilt head; Attaching the camera mounting base
11 Installation For a stand-alone installation Assembling the pan-tilt head When assembling the pan-tilt head, use the Allen key (provided) and screwdriver, and secure the head by tightening the screws firmly. After mounting the pan-tilt head, check there is no play in its installation. Attachin...
Page 12 - Mounting the tally lamp
1 Installation Mounting the tally lamp Connect the cable connector which is taped to the top of the pan-tilt head to the tally cable connector.Mount the tally lamp on the top of the pan-tilt head using the two screws provided.Mount the lamp while paying attention to the wire. The cable for the tal...
Page 13 - Concerning the safety modes; Mode for ensuring safety in the case of collisions
1 Installation Concerning the safety modes This unit comes with two safety modes which are designed to safeguard the user and others from injury and to prevent damage to the pan-tilt head. 1. Mode for ensuring safety in the case of collisions When the rotary arm of the pan-tilt head or some other ...
Page 15 - Setting the CPU circuit board switches; Setting SW1; Concerning the zoom offset automatic compensation function
15 Installation Setting the CPU circuit board switches Setting SW1 These switches are used to set the operations of the AW-PH405. Before changing their settings, make sure that the power has been turned off.No.1: Auto focus (AF)/extender (EXT) selector switch. Use this at the ON position when us...
Page 16 - Pan-tilt head mounting conditions; Notes; Installing the pan-tilt head
16 Installation Pan-tilt head mounting conditions Pan-tilt head weight Mounting specifications Compatible cameras Camera weight Camera anti-drop measures Compatible lenses Lens weight Cable weight Total weight Approx. lbs (10 kg) Stand-alone installation or installation on the celling Convertible ...
Page 18 - Mounting the camera
18 Mounting the camera [Convertible camera AW-E350/E650/E655/E750/E860 ] When mounting the camera, take sufficient care to ensure that the camera will not come off or fall down. Mount the lens onto the convertible camera. (Before mounting a large lens, consult with your dealer.) Mount the conv...
Page 19 - Attaching the wire; For installation on the ceiling
19 Installation Attaching the wire [Convertible camera AW-E350/E650/E655/E750/E860 ] The camera comes with a wire for preventing the camera from dropping. Follow the instructions below to use it to couple the camera to the pan-tilt head. When mounting the cameras with fan (AW-E655, AW-E750, AW-E86...
Page 21 - Concerning the balance of the installed unit; How to obtain the balance
1 Concerning the balance of the installed unit The weight balance may be impaired when the pan-tilt head is used in combination with a camera and long lens. Follow steps to below to check the balance, and then mount the camera. If, after this, the balance is still impaired and operations canno...
Page 24 - Connections; For a convertible camera
4 Connections Turn off the power of all the equipment before proceeding with the connections. Connect the AC power cable supplied with the AW-PH405 for the AW-PH405 indoor pan-tilt head. Use 10BASE-T straight cables to connect the RP connectors on the pan-tilt heads with the CONTROL OUT TO PAN...
Page 25 - Switch settings
5 Connections For the AK-HC1500G Use the connecting cables below to connect the pan-tilt head and camera. AW-CA15H9G Refer to the operating instructions for using the connecting cable to ensure that it is connected properly. Motorized zoom lens Iris control cable Monitor Camera cable AW-CA15H29G...
Page 26 - Cable specifications; When connecting a Fujinon extender change unit; When connecting a Canon lens with motorized extender unit
6 Cable specifications When connecting a Fujinon extender change unit SHELL CVCC (12 V)CGNDEXT ReturnEXT SignalND ReturnND SignalCanonEXT ( ) CanonEXT ( ) GNDGND Connector: HR10A-10P-10P (73) made by Hirose Electric SHELL Connect this connector to the ND/EXT connector on the pan-tilt head Connec...
Page 27 - Replacing the consumable parts; Replacing the motor
7 Replacing the consumable parts Replacing the motor Replace the motor when it ceases to operate properly.For details on the motor replacement, consult your dealer. Replacing the belt Replace the belt when the preset stop accuracy has deteriorated.For details on the belt replacement, consult you...
Page 28 - Appearance
8 Appearance Unit: inch (mm) 5-/8 (17) 7-/16 (18) 1-9/16 (19) 6-1/ (165) 8-1/4 ( 09) 16- /8 (416) 6-5/8 (168) ø6-5/16 (160) 1-5/8 (4 ) ø5-/4 (146) ø6-5/16 (160) ø5-/4 (146) 4-M6 screws <Mounting hole specifications> 1-7/8 (47) ø6-5/16 (160) -1/16 (71) -1/16 (97)
Page 29 - Specifications; Power consumption: 10 W
9 Specifications Genlock input: BNC Black burst or composite video signal, Tri Sync Prompter input (PROMPTER IN): BNC Through output to PROMPTER connector Prompter output (PROMPTER OUT): D-SUB 15-pin Camera video output VIDEO: BNC, 75-ohm output Y: BNC, 75-ohm output Pr/C: BNC, 75-ohm output Pb: BNC...
Page 30 - Memo
0 Memo — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
