Page 2 - CAUTION
Warning:This equipment generates and uses radio frequency ener-gy and if not installed and used properly, i.e., in strictaccordance with the instruction manual, may cause harmfulinterference to radio communications. It has been testedand found to comply with the limits for a Class A computingdevice ...
Page 3 - CONTENTS
-1- CONTENTS FEATURES .................................................................................................................................................................................. 2 PRECAUTIONS ........................................................................................
Page 4 - FEATURES; • The Multiport Hub AW-HB505 is combined with the
-2- FEATURES • The Multiport Hub AW-HB505 is combined with the Multi-Hybrid Control Panel (AW-RP505) to control up tofive Pan/tilt Heads (AW-PH300) and Color VideoCameras (AW-E560). When the Multiport Hub AW-HB505 is connected to the Multi-Hybrid Control Panelwith three coaxial cables (5C-2V) and a ...
Page 5 - PRECAUTIONS; • Do not use benzine, paint thinner, or other volatile
-3- • Use only with AC Adaptor, Model AW-PS505. • Handle the control panel with care. Dropping the control panel or subjecting it to a strongshock can cause a failure or an accident. • Operating temperature range –10°C to +45°C Avoid using it in a cold place below –10°C or a hotplace above +45°C bec...
Page 6 - MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS; FRONT PANEL; Lights red when Power ON/OFF Switch
-4- MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS P O W E R 1 Y C 2 Y C 3 Y C 4 Y C 5 Y C O F F O N C A B L E C O M P M u l t l P o r t H u b A W - H 8 5 0 5 ■ FRONT PANEL q Power Indicator [POWER] Lights red when Power ON/OFF Switch w is in the ON position, and goes out when the same switch is set t...
Page 8 - REAR PANEL
-6- C A M E R A C O N T R O L O U T C A M E R A C O N T R O L I N V I D E O O U T PA M / T I LT C O N T R O L O U T PA M / T I LT C O N T R O L I N S - V I D E O O U T V I D E OI N G / LO U T G / LI N C A M E R A C O N T R O L O U T V I D E O O U T PA M / T I LT C O N T R O L O U T S - V I D E O O U...
Page 9 - and
-7- o Camera Control Input Connector [TO CONTROLPANEL, CAMERA CONTROL IN] Connect it to Camera Control Input Connector [CAM-ERA CONTROL OUT] on the multi hybrid control panelwith a coaxial straight cable (5C-2V or equivalent),which may be extended up to 10 meters. !0 Pan/tilt Control Output Connecto...
Page 10 - INSTALLATION OF PAN/TILT HEAD
-8- • Install the pan/tilt head after carefully reading the Operating Instructions for Pan/tilt Head. • Have four hex bolts (M6 x 4) ready for mounting the pan/title head. Select bolts of a length appropriate tothe material and structure of the mounting base and theoverall weight applied to it. Fast...
Page 11 - • Changing Switch Settings on Pan/tilt Head; * Be careful of the Tally Indicator wire.; Tally Indicator
-9- • Changing Switch Settings on Pan/tilt Head q Remove the cover from the pan/tilt head. * Be careful of the Tally Indicator wire. w Shift the mounting direction switches (SW1, SW2) onthe pan/tilt head depending on whether the head issuspended from the ceiling or mounted on the floor.They are orig...
Page 12 - • Shifting Cable Compensation Switch on Pan/tilt
-10- ON OFF • Shifting Cable Compensation Switch on Pan/tilt Head If the distance from the control panel to the pan/tilthead is longer than 300 meters, set the cable compen-sation switch to the ON position by observing the fol-lowing procedure. q Remove the controller connection panel from thepan/ti...
Page 13 - CONNECTION
-11- CONNECTION • Before making any connection, switch off all the com- ponents of the system. • Use the Control Panel AC Adaptor AW-PS301 (optional) and Pan/tilt Head AC Adaptor AW-PS300 (optional). • Use the Pan/tilt Head AW-PH300 and the Color Video Camera WV-E550 or AW-E560. (The color VideoCame...
Page 14 - • Connect the iris control cable of the motor-driven zoom
-12- ITEM(AWC) UP(ABC) PAGE DOWN (BAR) IRIS G/L IN VIDEO OUT ZOOM/FOCUS REMOTE VD VIDEO/RGB VBS/HD 75 ON OFF CONTROL EXT DC IN SEE MANUAL CAUTION • Connect the iris control cable of the motor-driven zoom lens to the camera and the remote (zoom/focus control)cable to the pan/tilt head. If the remote ...
Page 15 - • Connect the multiport hub to the multi hybrid control
-13- C A M E R A C O N T R O L O U T C A M E R A C O N T R O L I N V I D E O O U T PA M / T I LT C O N T R O L O U T PA M / T I LT C O N T R O L I N S - V I D E O O U T V I D E OI N G / LO U T G / LI N C A M E R A C O N T R O L O U T V I D E O O U T PA M / T I LT C O N T R O L O U T S - V I D E O O ...
Page 16 - Expample of System Connection; Multi Hybrid Control panel AW-RP505
-14- S-VIDEO VIDEO PREVIEWVIDEO VIDEO CONTACT PAN/TILTCONTROL PAN/TILTCONTROL CAMERA CONTROL CAMERA CONTROL SYSTEMTALLY G/L G/L DC-15V OPTIONSWITCH CONTROL PREVIEWVIDEO G/L ON POWER OFF POWER O I FUSE(POWER) 3.15A FUSE FUSE Option Unit SEG, Switcher etc. POWER ON OFF Color Monitor WV-CM 1470 PUSH PO...
Page 17 - OPERATION; The switches on the pan/tilt head have been pre-; Up tilting limiter
M E M O R Y P R E S E T 2 1 3 4 5 6 7 8 9 1 0 -15- OPERATION 1. Power Set the power switches on the pan/tilt head AC adapterand the multiport hub AC adapter to the ON position,then set Power control Switch on the multi control panelto the ON position. 2. Pan/tilt Limiter Setting for Pan/tilt Head If...
Page 18 - ) After selecting a camera with the CONTROL switch on
-16- e Right Panning LimiterTurn the pan/tilt head to the desired right panning limitwith PAN/TILT Lever of the multi hybrid control panel,keep MEMORY Switch depressed, and simultaneouslypress buttons [4] and [9] of PRESET Switch for 5 sec-onds or more. When the desired limit has been set,button [5]...
Page 19 - pedestal of the selected camera.; • Cable Compensation; Turning CABLE COMP Y control changes not; CABLE COMP C Control
-17- 2) Adjust the cable compensation, genlock, and total pedestal of the selected camera. • Cable Compensation Signal degradation due to cable length between the con-trol panel and the pan/tilt head can be compensated for. q If the cable length from the pan/tilt head to the controlpanel is longer t...
Page 20 - • Genlock Adjustment; • Horizontal Phase Adjustment; When G/L PHASE ON/OFF Switch of the multi
-18- GRAY YELLOW CYAN GREEN MAGENTA RED BLUE 100 90 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 +69 +77 +56 +48 +38 +12 +7 -5 -16 -16 +15 +28 +36 +20 -20 +20 -20 +100+100 +89 +77 +72 +46 IRE 75% 100% 1V[p-p] +100 +27 +27 -20 -13 -13 100 90 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 IRE 75% 100% +20 -20...
Page 21 - Subcarrier Phase Adjustment; Video signal
-19- e Set G/L PHASE ON/OFF Switch of the multi hybrid con-trol panel back to the OFF position. • Subcarrier Phase Adjustment q Set G/L PHASE ON/OFF Switch (15) of the multi hybridcontrol panel to the ON position. Note: When G/L PHASE ON/OFF Switch of the multi hybrid control panel is set to the ON ...
Page 22 - • Total Pedestal Adjustment; White Balance and Black Balance
-20- • Total Pedestal Adjustment Total pedestal adjustment is made to adjust thepedestals of two or more cameras. Using an oscillo-scope or a waveform monitor, adjust the pedestals to 5IRE (0.035 V) or 7.5 IRE (0.050 V) with T.PED Control ofthe multi hybrid control panel. T . P E D C A B L E C O M P...
Page 23 - • Automatic Tracing White Balance Control (ATW); The white balance may deviate if there is noth-
-21- w Pick up a white object (a white wall or white handker-chief, for example) fully on the screen. Be careful tokeep a shiny or bright object out of the screen. e When AWC Switch of the multi hybrid control panel ispressed, the auto Auto set Indicator flashes and thewhite balance is automatically...
Page 24 - Various Switch Settings
-22- 5. Camera and Pan/tilt Head Presetting 1) Select a camera and pan/tilt head with the CONTROL switch on the multi hybrid control panel. 2) Pick up a desired object with the camera using PAN/TILT Lever ZOOM Lever and FOCUS Lever of themulti hybrid control panel. Select a white balance con-trol mo...
Page 25 - RACK MOUNTING; Press the power switch to turn power off.; Rack mounting bracket
1 Y C 2 Y C 3 Y C 4 Y C 5 Y C C A B L E C O M P 1 Y C 2 Y C 3 Y C 4 Y C 5 Y C C A B L E C O M P 1 Y C 2 Y C 3 Y C 4 Y C 5 Y C C A B L E C O M P -23- RACK MOUNTING To mount the multiport hub in a rack, use the supplied rackmounting brackets and screws (M4x10). q Press the power switch to turn power o...
Page 26 - SPECIFICATIONS
-24- SPECIFICATIONS Source Voltage 12 V DC (4-pin cannon connector) Power Consumption 12V, 2A Video Input 1.0 V[p-p] composite/75 Ω x 5 (BNC connector) Genlock Input 1.0 V[p-p] black burst/75 Ω (BNC connector) Camera Control Intput Control signal (BNC connector) Pan/tilt Control Intput Control signa...
Page 27 - ACCESSORIES
-25- Operating temperature − 10°C to +45°C (14°F to +113°F) Dimensions 420 (W) x 88 (H) x 250 (D) mm [16-9/16" (W) x 3-7/16" (H) x9-13/16” (D)] Weight 4 kg (8.8 lbs.) Finish Cover: AV Ivory vinyl chloride steelPanel: AV Ivory painting Weight and dimensions indicated are approximate.Specifica...
Page 28 - Printed in Japan; Broadcast & Television Systems Company
N1197-0 7J1A108A Printed in Japan Broadcast & Television Systems Company Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 2E-6, Secaucus, NJ 07094 Regional Offices:EASTERN ZONE: 43 Hartz Way, Secaucus, NJ 07094 (201) 348-7620CENTRAL ZONE: 1707 North Rand...
