OPTOMA TS551 - Manual

EN-6 Package Contents When you unpack the projector, make sure you have all these components: Note „ For European warrant information please visit www.optomaeurope.com „ Due to the difference in applications for each country, some regions may have different accessories. „ Contact you dealer immediat...

EN-7 Projector Overview Front View Front IR remote control sensor Control panel Elevator foot Zoom ring Projection lens Focus ring Speaker Lamp cover Ventilation holes 3 2 1 5 6 7 8 9 4 1 6 2 7 3 8 4 9 5

EN-8 Rear View AC power socketConnection ports (HDMI is only on certain models) Kensington lock Bottom View Security bar Ceiling mount holesVentilation holes Note „ This projector can be used with a ceiling mount for support. The ceiling mount is not included in the package. „ Contact your dealer fo...

EN-9 Using the Product Control Panel Power Turn the projector on or off. SOURCE Switch between input signals. MENU/EXIT Display or exit the on-screen display menus. Keystone ( / ) Manually correct distorted images resulting from an angled projection. Four directional buttons Use four directional but...

EN-10 Connection Ports AUDIO IN Connect an audio output from video equipment or computer to this jack. HDMI (HDMI is only on certain models) Connect HDMI output from video equipment to this jack. S-VIDEO Connect S-Video output from video equipment to this jack. VGA1-IN/YPbPr Connect image input sign...

EN-11 Remote Control Switch Switch to mouse mode when the on-screen menus are close. Source Switch between input signals. Four directional buttons Use four directional buttons to select items or make adjustments to your selection. Left mouse Perform the left button of the mouse when mouse mode is ac...

EN-13 Installing the Batteries 1. Open the battery cover in the direction shown. 2. Install batteries as indicated by the diagram inside the compartment. 3. Close the battery cover into position. Caution „ Risk of explosion if battery is replaced by an incorrect type. „ Dispose of used batteries acc...

EN-14 Remote Control Operation Point the remote control at the infrared remote sensor and press a button. „ Operating the projector from the front Note „ The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote sensor. „ Operate...

EN-15 Connection When connecting a signal source to the projector, be sure to:1. Turn all equipment off before making any connections.2. Use the correct signal cables for each source.3. Ensure the cables are firmly inserted. 1. ...........................................................................

EN-16 Connecting a computer or monitor Connecting a computer The projector provides two VGA input sockets that allow you to connect them to both IBM ® compatibles and Macintosh ® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers. To connect the projector to ...

EN-17 Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: „ HDMI „ Component Video „ S-Video „ Video (composite) You need only connect the projector to a Video source device using just one of the above c...

EN-18 Connecting an HDMI source device Examine your Video source device to determine if it has a set of unused HDMI output jacks available: „ If so, you can continue with this procedure. „ If not, you will need to reassess which method you can use to connect to the device. To connect the projector t...

EN-19 Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: „ If so, you can continue with this procedure. „ If not, you will need to reassess which method you can use to connect to the device. To connect the projector ...

EN-20 Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available: „ If so, you can continue with this procedure. „ If not, you will need to reassess which method you can use to connect to the device. To ...

EN-21 Operation Powering On/Off the Projector Powering On the Projector: 1. Complete the AC power cord and peripheral signal cable(s) connections.2. Press to turn on the projector. The projector takes a minute or so to warm up. 3. Turn on your source (computer, notebook, DVD, etc.). The projector au...

EN-22 Adjusting the Projector Height The projector is equipped with an elevator foot to adjust the image height. To raise or lower the image, turn the elevator foot to fine-tune the height. Note „ To avoid damaging the projector, make sure that the elevator foot is fully retracted before placing the...

EN-23 Adjusting Projection Image Size Refer to the graphic and table below to determine the screen size and projection distance. Note „ Position the projector in a horizontal position; other positions can cause heat build-up and damage to the projector. „ Keep a space of 30 cm or more between the si...

EN-24 Menu Operation The projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings. How to operate 1. Press MENU on the projector or Menu on the remote control to open the OSD menu. 2. When OSD is displayed, use / to select any featu...

EN-26 Image Brightness Brighten or darken the image. Contrast Set the difference between light and dark areas. Color Settings Adjust the color temperature. At higher temperature the screen looks colder;at lower temperature, the screen looks warmer. If you select “User”, then youcan change the intens...

EN-28 Signal Frequency Adjust the timing of the projector relative to the computer. Tracking Adjust the phase of the projector relative to the computer. H Position (Horizontal Position) Adjust the image left or right within the projection area. V Position (Vertical Position) Adjust the image up or d...

EN-29 Video Image Color Adjust a video image from black and white to fully saturated color. Sharpness Sharpen or soften the image. Tint Shift colors toward red or green. Sound Volume Adjust the volume level. Mute Cut off the sound temporarily.

EN-30 Setting Menu Position Choose the menu location on the display screen. Projection Adjust the picture to match the orientation of the projector: upright or upside-down, in front of or behind the screen. Invert or reverse the imageaccordingly. Color Space Select an appropriate color matrix type f...

EN-32 Language Select the language used by the on-screen menu. Factory Default Restore settings to factory default .

EN-33 Appendix Replacing the Lamp As the projector operates over time, the brightness of the projector lamp gradually decreases and the lamp becomes more susceptible to breakage. We recommend replacing the lamp if a warning message is displayed. Do not attempt to replace the lamp yourself. Contact t...

EN-35 Ceiling mount installation 1. To prevent damage to your projector, please use the Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications: „ Screw type: M4*3 „ Maximum screw ...

EN-36 Compatibility Modes Computer: Mode Resolution H-Sync [KHz] V-Sync [Hz] 640 x 350 31.5 70 640 x 350 37.9 85 720 x 350 31.5 70 640 x 400 31.5 70 640 x 400 37.9 85.1 720 x 400 31.5 70 720 x 400 37.9 85 720 x 576 - 50 720 x 576 - 60 VGA 640 x 480 31.5 60 - 67 37.9 72.8 37.5 75 43.3 85 SVGA 800 x 6...

EN-39 RS232 Commands and Protocol Function List RS232 Pin Assignments D-Sub 9 pin 1 1 CD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI Wire List C1 COLOR C2 1 Black 1 2 Brown 2 3 Red 3 4 Orange 4 5 Yellow 5 6 Green 6 7 Blue 7 8 Purple 8 9 White 9 SHELL DW SHELL

EN-40 RS232 Protocol Function List Note „ There is a <CR> after all ASCII commands. „ 0D is the HEX code for <CR> in ASCII code. Baud Rate : 9600 Data Bits: 8 Parity: NoneStop Bits: 1Flow Control : NoneUART16550 FIFO: DisableProjector Return (Pass): P Projector Return (Fail): F XX=01-99,...

EN-43 Troubleshooting Refer to the symptoms and measures listed below before sending the projector for repairs. If the problem persists, contact your local reseller or service center. Please refer to "LED Indicator Messages" as well. Start-up problems If no lights turn on: „ Be sure that the...

EN-44 LED Indicator Messages Projector Status POWER TEMP LAMP Standby mode Blue solid Off Off Normal running mode Flashing 30 seconds after powering on and then become solid blue Off Off Normal cooling Blue solid Blue solid Red solid Lamp ignition failed Blue solid Off Red flashing Lamp life end Blu...

EN-45 Optoma Global Offices For service or support please contact your local office. USA 3178 Laurelview Ct.Fremont, CA 94538, USA 888-289-6786 www.optomausa.com [email protected] Canada 5630 Kennedy Road, Mississauga, 905-361-2582 ON, L4Z 2A9, Canada 905-361-2581 www.optoma.ca [email protected]...

EN-48 Regulation & Safety Notices This appendix lists the general notices of your projector. FCC Notice This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection ...