OPTOMA EP 610 (H) - Manual

English 5 Product Overview w Main Unit Installation * There are two elevator releasing buttons and elevator feet on both sides. * There are also two remote control receivers on the front and the rear side. Remote Control Receiver Carrying Handle Projection Lens Elevator Foot Elevator Releasing Butto...

English 6 wwwww Panel Controls Computer 1Input Connector Power Connector Computer 2Input Connector Monitor Loop-ThroughConnector Audio Output Connector Audio Input Connector Audio Input for Computer Composite Video Connector S-Video Connector w Connection Ports Four Directional Select Keys Enter

English 7 w Remote Control Freeze/CLR Zoom In / Zoom Out Mute Keystone Power/Standby Source Volume Four Directional Select Keys Menu Enter Reset Resync Tracking

English 8 Connecting the Projection Display Power Cord Audio Cable S-Video Cable VGA Cable Audio Cable Monitor Cable RCA Audio Video Cable

English 9 u u u u u Powering On the Projection Display. 1. Remove the lens cover2. Plug the power cord into the back of the projector and plug it into the electrical outlet. The “ POWER/STANDBY ” LED indicator will flash green. 3. Turn on the lamp by pressing “ POWER/STANDBY ” button. The startup sc...

English 1 0 Adjusting the image size wwwww Adjust the height of projected image  Raise the projection display to the desired angle and then press the elevator release buttons to release the elevator foot. ‚ Fine-tune the height by manually turnig each foot. Screen Elevator Foot Elevator Releasing B...

English 1 1 wwwww Focus the image You may adjust zoom ring to zoom in/out 1.3 times of the image size. To focus the image, rotate the focus ring until the image is clear. 20” [27”] [60”] (20”) [100”] (45”) (76”) (114”) [150”] (153”) [200”] [260”] (197”) [ ] Maximum Max. Screen (inch) Distance(ft.) M...

English 1 2 User Control Overview There are two ways for you to control the functions: panel control and remote control. w Panel Control w Remote Control User Controls

English 1 4 4 The Projector has the multilingual On-Screen Display(OSD) menus that allows you to make image adjustments and change a variety of settings. When in computersource, the OSD will be the “Computer OSD”. When in Video source, the OSD willbe the “ Video OSD”. The projector will detect the s...

English 1 5 4 Tracking Choose “ Tracking “ item to synchronize the signal timing of the display with that of the graphic card. When you experience an unstable or flickering image, use this function to correct it. 4 Frequency “Frequency” is for changing the display data frequency to match the frequen...

English 1 6 4 Front-Desktop The factory default setting. 4 Rear-Desktop When you select this function, the projector reverses the image so you can project behind a translucent screen. 4 Front-Ceiling When you select this function, the projector truns the image upside down for ceiling-mountedprojecti...

English 1 7 Lamp Exit Menu 4 Exit Menu When you like to close the OSD menus, choose this item and select “ YES” to exit menu. 4 Reset All Choose “ Yes” to retrun the display parameters of the current mode to its factory default settings. 4 Lamp Warning Choose this function to show or hide the warnin...

English 1 8 Problem: No image appears on screen. 4 Ensure all the cables and power connections are correctly and securely connectedas described in the “Installation” section. 4 If the projector is plugged into a power strip, make sure the power strip is turned on. 4 Ensure the pins of connectors are...

English 2 1 Maintenance wwwww Cleaning the Air Filter 4 Cleaning Procedure: 1. Turn off the power. 2. Remove the air filter cover. 3. Remove the air filter from the filter cover. 4. Clean the air filter with a vacuum cleaner. 5. Place the air filter back in position. Make sure the air filter is full...

English 2 2 w Changing the lamp The projection display will detect the lamp life itself. It will show you a warningmessage when the lamp is used over working hours. When you see this message,change the lamp as soon as possible. Make sure the projection display has been cooled for at least 60 minutes...

English 2 4 Specifications LCD panel - active matrix TFT color LCD - 0.9” poly-silicon panels x 3 - tr=12ms, tf=30ms response time - 350:1 contrast ratio L am p - 150-watt UHP lamp Number of Pixels - 800 pixels (H) X 600 lines (V) Displayable Color - 16.7M colors Projection Lens - F1.8 ~2.0, f 38~50...

English 2 5 Compatibility Modes *: Compressed A G V A S E V & M B I 0 5 3 x 0 4 6 5 . 1 3 0 7 A G V A S E V & M B I 0 5 3 x 0 4 6 9 . 7 3 5 8 A G V A S E V & M B I 0 8 4 x 0 4 6 5 . 1 3 0 7 A G V A S E V & M B I 0 8 4 x 0 4 6 9 . 7 3 5 8 A G V A S E V & M B I 0 0 4 x 0 2 7 5 . 1 ...