Nutone LA-245MR - Manual

Nutone LA-245MR

Nutone LA-245MR – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
Page: / 6

Table of Contents:

  • Page 2 – P R E PARING THE RECEIVER; TROUBLESHOOTING GUIDE; P R O B L E M; S O L U T I O N; FIGURE 6
  • Page 3 – Le carillon sans fil; I N S TA L L ATION DU BOUTO N - P O U S S O I R / T R A N S M E T T E U R
  • Page 4 – FIGURE 5; FIGURE 7; P R É PA R ATION DU RÉCEPTEUR; GUIDE DE DÈP A N N A G E; P R O B L È M E
  • Page 5 – Campana Inalámbrica; SELECCION DEL SONIDO; M O N TAJE DEL PULSADOR DE TRANSMISION
  • Page 6 – P R E PARACION DEL RECEPTO R; GUIA DE DETECCION Y SOLUCION DE PROBLEMS; P R O B L E M A; S O L U C I O N; FIGURA 6
Loading the manual

Refer to Figures 1 and 2.

1. Locate the pushbutton next to or near

the door.

Do not mount the pushbutton
on a metal surface.

2. Remove the pushbutton cover by

inserting the tip of a screwdriver in
the slot at the bottom of the pushbutton
and then gently rock the pushbutton
cover apart from the pushbutton base.

3. Choose a level place to locate the

pushbutton base.

4. Position the pushbutton base,

and mark the mounting surface with
a pencil through the two holes in
the pushbutton.

5. Drill two

3

/

1 6

" diameter holes at

the previously marked area.

6. Insert the plastic anchors into

the

3

/

1 6

" diameter holes.

7. Place pushbutton over anchors,

and fasten with two screws provided.
Do not replace cover at this time.

P U S H B U T TON SOUND CODING

Refer to Figure 3.

1. The pushbutton can be coded to sound

one of three chime sounds.

2. Select the desired sound as illustrated

in Figure 3.

3. Position the plastic jumper straps

in the proper location for desired
chime sound.

P U S H B U T TON SECURITY
C O D I N G

Refer to Figure 3.

It is not necessary to change the

security code of the pushbutton unless
you experience interference from other
wireless devices.
1. To change the security code, remove

any combination of the six plastic
jumper straps.

2.

NOTE: Both the pushbutton and
receiver codes must match.

B AT T E RY INSTA L L AT I O N

Refer to Figure 3.

1. Position the A23 12 volt battery

as illustrated.

Be sure to observe

polarity (+/–).

For replacement

battery, use EverReady

®

A23BP or

D u r a c e l l

®

MN21B (or equivalent).

I N S TALLING PUSHBUTTO N
C O V E R

Refer to Figure 4.

1. Position the pushbutton cover over

the pushbutton base. The red light
must be lined up over the hole in the
pushbutton cover. Firmly press cover
over base.

INSTALLATION & OPERATING INSTRUCTIONS

READ & SAVE THESE INSTRUCTIONS!

Wireless Chimes

MODELS: LA-228WH

or LA-245MR

•

For use with the LA-206TWH

FIGURE 1

FIGURE 2

TO OPEN COVER
“PUSH”

SCREW HOLE FOR WALL
MOUNTING

SCREW HOLE FOR WALL
MOUNTING

+

–

6

5

4

3

2

1

ONE NOTE

TWO NOTE

WESTMINSTER

SECURITY

CODE SETTING

FIGURE 3

SOUND SELECTION

12V “A23”
BATTERY

LED

Congratulations on your purchase of a NuTone wireless chime. The chime operates

by a radio frequency signal transmitted by the pushbutton and received by the chime.
The pushbutton/transmitter is mounted at the door. The receiver may be located
anywhere in your home within 100 feet (30 meters) of the pushbutton. The
pushbutton/transmitter can be programmed to sound one of three chime sounds.
This feature allows up to three pushbuttons to generate three different chime sounds.

FIGURE 4

MOUNTING THE PUSHBUTTON TRANSMITTER

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - P R E PARING THE RECEIVER; TROUBLESHOOTING GUIDE; P R O B L E M; S O L U T I O N; FIGURE 6

REMOVING THE RECEIVER COVER Refer to Figure 5. 1. Gently push up on the chimes’ cover to disengage the cover from the baseand pull cover away from base. 2. Set chime cover aside. MOUNTING THE CHIME BASE Refer to Figure 6. 1. Select the desired mounting location. Thislocation should be at least1 foot...

Page 3 - Le carillon sans fil; I N S TA L L ATION DU BOUTO N - P O U S S O I R / T R A N S M E T T E U R

Voir les Figures 1 et 2. 1. Placer le bouton-poussoir près de la porte. Ne pas installer le bouton- poussoir sur une surface métallique. 2. Retirer le couvercle du bouton-poussoir en insérant la pointe d’un tourne-visdans la fente située dans le bas du bouton-poussoir, puis en faisantdoucement tourn...

Page 4 - FIGURE 5; FIGURE 7; P R É PA R ATION DU RÉCEPTEUR; GUIDE DE DÈP A N N A G E; P R O B L È M E

RETRAIT DU COUVERCLE DU RÉCEPTEUR Voir la Figure 5. 1. Poussez doucement le couvercle du carillon vers le haut, pour le sortir du socle. 2. Mettre le couvercle de côté. I N S TA L L ATION DU RÉCEPTEUR Voir la Figure 6. 1. Choisir l’emplacement désiré. Ce dernier doit être situé à moins unpied de tou...

Other Nutone Models