Nutone LA-205WH - Manual
Nutone LA-205WH – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – FIGURE 4; TROUBLESHOOTING GUIDE; PROBLEM; SOLUTION; FIGURE 5; PREPARING THE RECEIVER
- Page 3 – Voir les Figures 1 et 2.; Ne pas installer le; CODE DE SÉCURITÉ DU BOUTON-POUSSOIR; Il faut s’assurer de; FIGURE 3
- Page 4 – PREPARATION DU RÉCEPTEUR; GUIDE DE DÉPANNAGE; PROBLÈME; RETRAIT DU COUVERCLE DU PILE; FIGURE4; INTERRUPTEUR ET COMMANDE DU VOLUME
INSTALLATION & OPERATING INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
Two-Note Wireless Chime
MODEL: LA-205WH
FIGURE 2
COVER
FIGURE 3
MOUNTING THE PUSHBUTTON
TRANSMITTER
Refer to Figures 1 and 2.
1. Locate the Transmitter next to or near the door.
Do not mount the
transmitter on a metal surface. Caution: Some stucco houses
have metal mesh in the wall structure which will affect the
wireless chime performance. Experiment with various positions
of receiver with respect to the pushbutton to determine the
location that gives best performance before mounting
permanently. If not satisfied, use a wired chime.
2. Remove the Transmitter cover by inserting the tip of a screwdriver in
the slot at the bottom of the Transmitter and then gently rock the
Transmitter cover apart from the Transmitter base.
3. Choose a level place to locate the Transmitter base.
4. Position the Transmitter base, and mark the mounting surface with a
pencil through the two holes in the Transmitter.
5. Drill two
3
⁄
16
” diameter holes at the previously marked area.
6. Insert the plastic anchors into the
3
⁄
16
” diameter holes.
7. Place Transmitter base over anchors, and fasten with two screws
provided. Do not replace cover at this time.
8. Apply a small amount of caulking to the mounting screw holes on the
base for waterproofing.
TRANSMITTER SECURITY CODING
Refer to Figure 3.
It is not necessary to change the security code of the Transmitter
unless you experience interference from other wireless devices.
1. To change the security code, remove any combination of the six plastic
jumper straps.
2.
NOTE: Both the Transmitter and Receiver codes must match.
BATTERY INSTALLATION
Refer to Figure 3.
1. Position the A23 12 volt battery
as illustrated.
Be sure to observe polarity (+/–).
For replacement
battery, use EverReady
®
A23BP or Duracell
®
MN21B (or equivalent).
INSTALLING TRANSMITTER COVER
1. Position the Transmitter cover over the Transmitter base so that the
“lip” on the base engages into the “slot” on the cover. Make sure the
rubber gasket is properly seated. Firmly press cover until it snap fits
over the base.
SLOT
DO NOT MOUNT ON
METAL SURFACE
LIP
MOUNTING
SCREWS
WATERPROOF
GASKET
BASE
WOODEN WALL OR
DOOR FRAME
PLASTIC
WALL
ANCHORS
TOP
P.C. BOARD
BATTERY
LOCATION
SECURITY CODE
SETTING
FIGURE 1
TO OPEN
COVER “PUSH”
SLOT
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
REMOVING THE RECEIVER COVER Refer to Figure 4. 1. Press the center of the battery cover, and slide cover toward bottom ofreceiver. 2. Set battery cover aside. RECEIVER SECURITY CODING Refer to Figure 5. Changing the Security Code is not necessary unless you have changed the security code in the Tran...
INSTRUCTIONS D’INSTALLATION LIRE ET CONSERVER CES INSTRUCTIONS! Carillon sans fil à deux tonalités MODELE: LA-205WH INSTALLATION DU BOUTON-POUSSOIR/TRANSMETTEUR Voir les Figures 1 et 2. 1. Placer le transmetteur près de la porte. Ne pas installer le transmetteur sur une surface métallique. Attention...
PREPARATION DU RÉCEPTEUR Product specifications subject to change without notice. Les spécifications de cet article peuvent changer sans préavis. 4820 Red Bank Road, Cincinnati, Ohio 45227 1140 Tristar Drive, Mississauga, Ontario Canada L5T 1H9 Imprimé aux Chine, Rev. 4/05, Piéce No. 85094 GUIDE DE ...
