Nutone LA-204WH - Manual
Nutone LA-204WH – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – TROUBLESHOOTING GUIDE; RECEIVER SECURITY CODING; PROBLEM; SOLUTION
- Page 3 – INSTALLATION DE LA PILE; S'assurer de respecter la; DIRECTIVES D’INSTALLATION; Carillon sans fil avec lumière stroboscopique; FIGURE 1; FIGURE 3; FIGURE 4; INSTALLATION DU BOUTON-POUSSOIR / TRANSMETTEUR
- Page 4 – GUIDE DE DÉPANNAGE; FIGURE 5; PROBLÈME; FIGURE 6; POUSSOIR; PRÉPARATION DU RÉCEPTEUR; CODE DE SÉCURITÉ DU RÉCEPTEUR; Les codes du; INSTALLATION DU RÉCEPTEUR; Brancher le récepteur dans une prise murale 120 V.
- Page 5 – INSTALACION DE LAS PILAS; Tenga en cuenta la; INSTRUCCIONES PARA LA INSTALACION Y OPERACION; Campana Inalámbrica con luz estroboscópica; MONTAJE DEL PULSADOR DE TRANSMISION; FIGURA 1; FIGURA 3; FIGURA 4
- Page 6 – GUIA DE DETECCION Y SOLUCION DE PROBLEMAS; FIGURA 5; PROBLEMA; FIGURA 6; PREPARACION DEL RECEPTOR; CODIGO DE SEGURIDAD DEL RECEPTOR; El código de; MONTAJE DEL PULSADOR; Enchufe el receptor en cualquier tomacorriente de pared
This device complies with RSS-210
of Industry Canada. Operation is subject
to the following two conditions: (1) this
device may not cause interference;
and (2) this device must accept any
interference, including interference
that may cause undesired operation
of the device.
Refer to Figures 1 and 2.
1. Locate the Pushbutton next to or near
the door.
Do not mount the pushbutton
on a metal surface.
2. Remove the Pushbutton cover by
inserting the tip of a screwdriver in
the slot at the bottom of the Pushbutton
and then gently rock the Pushbutton
cover apart from the Pushbutton base.
3. Choose a level place to locate the
Pushbutton base.
4. Position the Pushbutton base,
and mark the mounting surface with
a pencil through the two holes in
the Pushbutton.
5. Drill two
3
⁄
16
” diameter holes at
the previously marked area.
6. Insert the plastic anchors into
the
3
⁄
16
” diameter holes.
7. Place Pushbutton over anchors,
and fasten with two screws provided.
Do not replace cover at this time.
PUSHBUTTON SOUND CODING
Refer to Figure 3.
1. The Receiver strobe light will flash
with any chime sound selected. The
Pushbutton can be coded to sound
one of three chime sounds.
2. Select the desired sound as illustrated
in Figure 3.
3. Position the plastic jumper straps
in the proper location for desired
chime sound.
PUSHBUTTON SECURITY
CODING
Refer to Figure 3.
It is not necessary to change the
security code of the Pushbutton unless
you experience interference from other
wireless devices.
1. To change the security code, remove
any combination of the six plastic
jumper straps.
2.
NOTE: Both the Pushbutton and
Receiver codes must match.
BATTERY INSTALLATION
Refer to Figure 3.
1. Position the A23 12 volt battery
as illustrated.
Be sure to observe
polarity (+/–).
INSTALLING PUSHBUTTON
COVER
Refer to Figure 4.
1. Position the Pushbutton cover over
the Pushbutton base. The red light
must be lined up over the hole in the
Pushbutton cover. Firmly press cover
over base.
INSTALLATION & OPERATING INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
Wireless Chime with Strobe Light
MODEL: LA-204WH
NuTo
ne
FIGURE 1
FIGURE 2
TO OPEN COVER
“PUSH”
SCREW HOLE FOR WALL
MOUNTING
SCREW HOLE FOR WALL
MOUNTING
+
–
6
5
4
3
2
1
ONE NOTE
TWO NOTE
WESTMINSTER
SECURITY
CODE SETTING
FIGURE 3
SOUND SELECTION
12V “A23”
BATTERY
LED
FIGURE 4
NuT
one
+
–
MOUNTING THE PUSHBUTTON TRANSMITTER
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
+ – 6 5 4 3 2 1 SECURITY CODE SETTING TROUBLESHOOTING GUIDE PREPARING THE RECEIVER RECEIVER SECURITY CODING Refer to Figure 5. Changing the Security Code in not necessary unless you have changed the security code in the Pushbutton. Both the Pushbutton and Receiver codes must match. 1. Remove the scr...
Cet appareil est conforme à la norme CNR-210 d’industrie Canada. Sonfonctionnement est assujetti aux deuxconditions suivantes: (1) Cet appareil ne doitpas causer d’interférence. (2) Cet appareil doitfonctionner en dépit des interférence, ycompris les interférences qui pourraiententraîner un fonction...
4820 Red Bank Road, Cincinnati, Ohio 45227Imprimé aux Chine, Rev. 4/05, Piéce No. 83044 + – 6 5 4 3 2 1 REGLAGE DU CODE DE SECURITE GUIDE DE DÉPANNAGE O N 1 2 3 4 5 6 FIGURE 5 PROBLÈME 1. Le carillon ne sonne pas. • Vérifiez la pile et sa polarité dans le bouton-poussoir.• S'assurer que le bouton-po...
