Nutone CI370 - Manual
Nutone CI370 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – FINAL SYSTEM CHECK
- Page 3 – SYSTÈME D’ASPIRATION CENTRAL; Prises Avec Voyant; Cadre De Montage; INSTALLATION; MODE D’INSTALLATION
- Page 4 – VÉRIFICATION FINALE DU SYSTÈME
CENTRAL CLEANING SYSTEM
Indicating Inlets
MODELS: CI370 Series
USE ONLY WITH CV653, CV750 & CV850 POWER UNITS
Mounting Bracket
MODEL: 361
INSTALLATION
1. Once the locations for wall inlet locations have been
determined, mount all inlet brackets.
2. To locate bracket on wall stud, measure approximately 18" up
from finished floor level. (Height location may vary according to
individual preference.)
3.
Refer to Figure 1.
Nail bracket to side of stud so that front
edge of bracket is flush to front of stud. (The bracket may also
be nailed to the front edge of the stud. For front stud mounting,
use locating tabs on bracket for proper alignment.)
4.
Refer to Figure 2.
Remove cardboard from plaster guard
frame. Using four (4) provided screws, attach the appropriate
flanged fitting and inlet seal to back of inlet.
5. Replace cardboard into plaster guard frame.
6. Plumb tubing to inlet. Run 2-conductor (376 or 376UL)
low voltage cable between inlet and power unit.
CAUTION: When tubing is run through the wall stud, sole
plate, headers – or anywhere that building materials will be
attached – place a nail plate (Model 378) over that area (on
both sides if necessary) to prevent nails from piercing tubing.
WALL INLET INSTALLATION
1. Once the walls have been finished, install the wall inlets.
2. Remove the cardboard plaster guard.
3.
Refer to Figure 3.
For some dry wall or panel construction,
the plaster frame will extend beyond the finished wall. In this
case, remove plaster frame from mounting bracket by
removing mounting screws.
NOTE: When using the Model 361 inlet bracket on walls
thinner than
1
⁄
2
", use a
1
⁄
4
" spacer (not furnished) between
the wall and the inlet bracket. See Figure 3A.
Spacer may be made from plywood, Masonite™, etc. Contact
cement may be used to hold spacer in place during assembly.
Configuration of spacer may vary depending upon installation.
INSTALLATION INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
1
13
/
16
"
2
3
/
8
"
FIGURE 1
FIGURE 2
MODEL 361
SIDE
MOUNTING
FACE
MOUNTING
FIGURE 3
2
1
/
4
"
3
1
/
4
"
1
/
4
"
INLET MOUNTING
BRACKET
SPACER
WALL LESS THAN
1
/
2
" THICK.
PLASTER
GUARD
HOLE
FIGURE 3A
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Product specifications subject to change without notice. 4820 Red Bank Road, Cincinnati, Ohio 45227 • 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9 Printed in U.S.A., Rev. 4/01, Part No. 88384 FIGURE 5 FIGURE 6 FIGURE 7 MODEL 365C DOUBLE FLANGED TEE WALLINLET MOUNTING BRACKET CUT OFF APPR...
SYSTÈME D’ASPIRATION CENTRAL Prises Avec Voyant MODÈLE: CI370 Series UTILISER SEULEMENT AVEC LES APPAREILS CV653,CV750 et CV850 Cadre De Montage MODÈLE: 361 INSTALLATION 1. Une fois que vous avez déterminé les emplacements des prises murales, fixez tous les supports de prise. 2. Pour situer un suppo...
Les caractéristiques de produits peuvent changer sans préavis. 4820 Red Bank Road, Cincinnati, Ohio 45227 • 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9 Imprimé aux E.U. FIGURE 6 TÉ À DEUX BRIDES DE MODÈLE 365C PRISE MURALE SUPPORT DE FIXATION COUPEZ APPROXIMATIVEMENT UNE LONGUEUR DE 3 ⁄...
