Nutone 62BK244CCN(X) - Manual

MODEL

:

62BK244CBK(X), 62BK244CCN(X),

62BK244CCY(X), 62BK244CMP,

62BK244TBK(X), 62BK244TCY(X),

62BK244TGK(X), 62BK244TMP

RECESSED MOUNTED, STEEL

BATH CABINETS

INSTALLATION of CABINET

1. Carefully remove all packing material. Place hardware

packages, shelves and door aside until needed. Hardware

and shelves are located in the fi llers identifi ed by “Hardware

Enclosed”

tape.

2. Determine desired location of cabinet on wall. Mark wall to

show wall opening size (see dimension chart). Generally, the

recommended height to the center of the cabinet is 64” from

the fl oor. (Fig. 1)

3. CAUTION: Wall studs, plumbing or electrical lines that

interfere must be removed or relocated. Cut wall opening,

being careful not to damage the surrounding wall surface.

Insert framing to support all plaster board edges.

4. Prepare the mounting screws by placing the screws into the

plastic bases. (Fig. 2)

5. Note: For ease of installation, an additional person is

recommended. Insert cabinet into wall opening. (Fig.3)

Ensure the cabinet is plumb and level. If necessary use a

carpenter’s level and shim corners of cabinet. Secure to wall

studs through the four (4) mounting holes inside cabinet,

using the screws that have been placed into the plastic

bases. (Fig. 4) Do not over tighten the mounting screws as

the body side wall may bend and prevent proper shelf

installation. Only tighten screws until they are fl ush with the

body.

6. Snap the screw covers over the screw bases. (Fig.5)

INSTALLATION of DOORS

1. Remove hinges and screws from hardware bag. Mount

hinge unit on door as shown in Fig. 6 securing with screws

provided.

2. Install the door by inserting door side of the hinge into the

bracket on the body shown in Fig. 7.

3. Check door for proper alignment. If the door needs to be

adjusted please refer to the adjustment procedures in Fig. 8.

INSTALLATION of SHELVES, HOLE PLUGS AND BUMPERS

1. Select where you want the shelves to be placed.

2. Insert two (2) shelf brackets at each end of the shelf location.

(Fig.

9).

3. Set shelves in place on the shelf brackets, pressing down

on the shelf to lock in place. (Fig. 9).

4. Remove hole plugs from hardware bag and place in

remaining holes. (Fig. 10).

5. Remove bumpers from hardware bag and position to body.

(Refer to Service Parts Drawing - Key No. 9 for bumper

locations).

INSTALLATION INSTRUCTIONS

Fig. 2

Register your product online at www.nutone.com/register

For help, call us toll

free!

1-800-325-8351

MODEL

WALL OPENING

OVERALL SIZE

NO.

W H D W H D

62BK244CBK(X)

14

1

/

4

24 4

16

1

/

2

26

1

/

2

5

1

/

4

62BK244CCN(X)

14

1

/

4

24 4

16

1

/

2

26

1

/

2

5

1

/

4

62BK244CCY(X)

14

1

/

4

24 4 16

1

/

2

26

1

/

2

5

1

/

4

62BK244CMP

14

1

/

4

24 4

16

1

/

2

26

1

/

2

5

1

/

4

62BK244TBK(X)

14

1

/

4

24 4

16

1

/

2

26

1

/

2

5

1

/

4

62BK244TCY(X)

14

1

/

4

24 4 16

1

/

2

26

1

/

2

5

1

/

4

62BK244TGK(X)

14

1

/

4

24 4 16

1

/

2

26

1

/

2

5

1

/

4

62BK244TMP

14

1

/

4

24 4 16

1

/

2

26

1

/

2

5

1

/

4

Fig. 1

Approx.
64" to
Floor

W

D

H

Insert screw
through clear
plastic base

Fig. 3

Mounting
Screws

Mounting
screw into
mounting
hole

Fig. 4

Wall
Opening

Cabinet
Body

Snap on Cover

Cover

Base

Screw

Fig. 5

Hinge Mounted
to Door

Fig. 6

Hook bottom of
hinge into place
on the bracket

Press down
on hinge until it
clips in place

Hinge Mounted
to Cabinet

Fig. 7

Door Adjustment

This screw for
up and down
adjustments

This screw
for depth
adjustments

This screw
for left and right
adjustments

Fig. 8

Fig. 9

Fig. 10