Nuna Pipa - Manual

6 PIPA instructions 7 PIPA instructions WARNING Failure to follow these warnings, instructions and labels on the child restraint could result in serious injury or death. A child’s safety is your responsibility. NEVER leave your child unattended. Read all instructions before use of this child restrai...

11 PIPA instructions 10 PIPA instructions Car Seat Use after a Crash The National Highway Traffic Safety Administration (NHTSA) recommends that car seats be replaced following a moderate or severe crash. Car seats do not automatically need to be replaced following a minor crash.What defines a minor ...

1 2 3 4 5 6 13 PIPA instructions 12 PIPA instructions Vehicle belts that CANNOT BE USED with your child restraint: 1 - Motorized Belts (Automatic) These should not be used unless the shoulder belt can be removed, the lap belt is locked and use is allowed by the vehicle manufacturer. 2 - Dual Retract...

14 PIPA instructions 15 PIPA instructions Infant Car Seat Parts List 1 Canopy 2 Infant Insert 3 Chest Clip 4 Buckle and Crotch Belt 5 Adjuster Button 6 Adjuster Strap 7 Lap Belt Guides 8 Handle Button 9 Stroller Release Button 10 Shoulder Pads 11 Seat Cover 12 Handle 13 Shoulder Belt Guide 14 Stroll...

16 PIPA instructions 17 PIPA instructions Base Parts List 1 Lock Off 2 Rigid Latch (Lower Anchors) 3 Primary Rigid Latch Release Button 4 Secondary Rigid Latch Release Button 5 Latch Guides 6 Locking Clip 7 Stability Leg 8 Stability Leg Indicator 9 Stability Leg Adjust Button 10 Car Seat Release But...

Product Overview Canopy Drape1 - Unzip the zipper behind the front canopy bow. 2 - Pull the canopy drape out of the compartment and attach the canopy drape to the magnets on each corner to the front of the carrier. Canopy3 - To remove the canopy, undo the snap on the canopy fabric. Press the button ...

Handle Adjustment1 - The carrier handle can be adjusted to 3 positions. 2 - To adjust the handle position, squeeze handle buttons on both sides. 3 - Rotate handle until it clicks into any of the 3 positions. Handle can be used in vehicle in any locked position. Be sure handle is locked in the carry ...

Shoulder Belts1 - Tighten harness to fit snugly on child’s shoulders. It is snug if you cannot pinch a fold in the strap. 2 - Harness straps must be at or just below shoulders. 3 - To adjust shoulder harness height, remove child and loosen harness. 4 - Turn child restraint over and remove one harnes...

Product Use 1 - Top of child’s head is at least 1” below top of child restraint. Securing Child in Child Restraint2 - Loosen harness by pressing on adjuster button while pulling on the harness straps. 3 - Press button to release the buckles. Separate chest clip and spread harness straps apart. 4 - P...

1 - Listen for clicks. Pull on buckle to verify it is latched. 2 - Snap the chest clip together and temporarily slide towards buckle for tightening of harness. 3 - Tighten harness by pulling on the adjuster strap. Pull any excess harness webbing through the buckle towards the child’s shoulders and p...

Installation If child is not secured properly, child could be ejected in a sudden stop or crash, resulting in serious injury or death. Base Installation Using Rigid Latch (Lower Anchors) 1 - Place vehicle in park and on level ground. 2 - Position base in a forward facing vehicle seat. Use recline ad...

1 - Rotate rigid latch down. 2 - Hook rigid latch onto vehicle lower anchor bars. 3 - Confirm proper installation by pulling on the base AND also seeing that green is indicated on the connectors. The rigid latch must be attached and locked onto the vehicle anchor bars. Check Installation Base should...

1 - Recline adjustment locks into position. To release press down on lock button. When installing with the base, additional stability can be achieved by using the stability leg. For instructions on using the stability leg when installing the base, see Stability Leg section. 2 - Route the vehicle bel...

1 - After child is properly secured in child restraint, press child restraint on base and listen for a click. Pull on child restraint to verify installation. DO NOT allow child restraint to contact the vehicle door or seat in front of it. 2 - To release the child restraint, squeeze the car seat rele...

1 - After correctly installing the base on the vehicle seat, press the stability leg adjust button to extend the stability leg to the floor. 2 - Stability leg should make firm contact with the vehicle floor. 3 - Indicators should show green. When the stability leg indicator shows red this means the ...

49 PIPA instructions 48 PIPA instructions When installing in an airplane using a base, follow the instructions for vehicle installation with a base using lap belt only. This child restraint is certified for use in commercial aircraft with or without the base. Be sure to contact your airline prior to...