Novatel GM-14915118 - Manual
Novatel GM-14915118 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – IMU SETUPS; IMU
- Page 3 – INSTALL THE MIC IN A STACK UP CONFIGURATION; Ref; MIC
- Page 4 – Connects to the J301 connector on the MIC; Questions or Comments
- Page 5 – must not
- Page 6 – INSTALL THE MIC IN A STANDALONE CONFIGURATION; OEM628 Recommendations; to a computer without additional interface circuitry.; OEM638 Recommendations
- Page 8 – INSTALL THE PC UTILITIES; Start; Support; Serial
- Page 9 – CONNECTIMU; Table 1: CONNECTIMU Commands; If this is a serial connection, select; Baud Rate; If this is a serial connection, clear the; Use hardware handshaking; button to save the new connection.; Open; button to open SPAN receiver communications.
- Page 10 – LOG SPAN DATA; Data can be collected through NovAtel Connect using the
- Page 11 – OPERATE THE SPAN SYSTEM; Observe the status of the system in the NovAtel Connect; Table 2: Inertial Solution Status; INS is in alignment mode.
- Page 12 – QUESTIONS OR COMMENTS
1
MEMS Interface Card
GM-14915118
Rev 4
December 2013
QUICK START GUIDE
This guide provides the basic information needed to set up and use your new NovAtel
®
MEMS Interface
Card (MIC). For more detailed information on the installation and operation of your MIC, download the
BOX CONTENTS
In addition to this
Quick Start Guide
, the following is provided with your MIC:
• 1 MIC to IMU interface cable
• 1 IMU mounting PCB (printed circuit board)
(a PCB is not included with the OEM-IMU-STIM300)
• Screws and standoffs for mounting the MIC
ADDITIONAL EQUIPMENT REQUIRED
The additional equipment listed below is required for a typical setup:
• An OEM615 receiver
• An IMU (see the
IMU Type
column in
• A 10-30 VDC power supply
• A wiring harness to provide power to the P101 connector on the MIC (10-30 VDC).
• A wiring harness to connect the customers equipment to the P301 connector on the MIC.
• A quality, dual-frequency GNSS antenna such as the GPS-702-GG. See the NovAtel website
(
www.novatel.com/products/gnss-antennas/
) for information on a variety of quality antennas
available to meet your form factor and performance needs.
• An antenna cable
• A Windows
®
based computer
The MIC supports all OEM6
®
family receiver cards for communications. The OEM615 is the
only OEM6 family receiver card that can be directly integrated and powered by the MIC.
If the MIC is installed in a standalone configuration, a separate power supply is required for
the OEM6 family receiver. For information about the power supply requirements, refer to the
Technical Specification appendix for the receiver card in the
. This user manual is available from our website at
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 IMU SETUPS Figure 1: MIC to OEM-IMU-ADIS-16488 (OEM Cable Kit: 01019007) Figure 2: MIC to OEM-IMU-HG1700 (OEM Cable Kit: 01018868) Figure 3: MIC to OEM-IMU-HG1900 (OEM Cable Kit: 01018871) Figure 4: MIC to OEM-IMU-HG1930 (OEM Cable Kit: 01018869) MIC Cable (01019008) MIC to IMU Interface IMU IMU M...
3 Figure 5: MIC to OEM-IMU-STIM300 (OEM Cable Kit: 01019174) INSTALL THE MIC IN A STACK UP CONFIGURATION In a stack up configuration, the MIC is connected directly to an OEM615 receiver. Power and communications connections to the receiver are made through the MIC. Ref Connector Part Number Mating C...
4 Complete the following steps to connect and power your MIC and OEM615. 1. Attach the IMU mounting PCB to the IMU. Ensure all the pins on the header are aligned with the holes on the mating connector. 2. Mount the IMU and antenna securely to a vehicle. For the simplest operation, align the Y-axis o...
