Page 2 - ii
IL9 Pro User’s Manual English + Multilingual QIG 1 st Edition, October 2006 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may...
Page 3 - Hardware Setup; Contents; BIOS Setup; 繁體中文; IL9 Pro
Hardware Setup Contents 1. Hardware Setup ............................................................... 1-1 1.1 Specifications .............................................................................. 1-1 1.2 Motherboard Layout.....................................................................
Page 6 - Motherboard Layout
Page 7 - Choose a chassis big enough to install this motherboard.; Installing Motherboard; To install this motherboard:
Hardware Setup 1.3 Choosing a Computer Chassis • Choose a chassis big enough to install this motherboard. • As some features for this motherboard are implemented by cabling connectors on the motherboard to indicators and switches or buttons on the chassis, make sure your chassis supports all the fea...
Page 8 - Checking Jumper Settings; CMOS Memory Clearing Header and Backup Battery; Pins 1 and 2 shorted:
1.5 Checking Jumper Settings • For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position. SHORT OPEN OPEN • For 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging ...
Page 9 - ” or “
Hardware Setup CMOS Backup Battery: An onboard battery saves the CMOS memory to keep the BIOS information stays on even after disconnected your system with power source. Nevertheless, this backup battery exhausts after some five years. Once the error message like “ CMOS BATTERY HAS FAILED ” or “ CMO...
Page 10 - Connecting Chassis Components; Auxiliary 12V Power Connector:
1.6 Connecting Chassis Components 1.6.1 ATX Power Connectors These connectors provide the connection from an ATX power supply. As the plugs from the power supply fit in only one orientation, find the correct one and push firmly down into these connectors. ATX 24-Pin Power Connector: The power supply...
Page 11 - Pin
Hardware Setup 1.6.2 Front Panel Switches & Indicators Headers This header is used for connecting switches and LED indicators on the chassis front panel. Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below stands for positive polarity for the LED c...
Page 15 - Usually there is no hardware or BIOS setup required
Hardware Setup 1.7.2 DDR2 Memory Slots • To reach the optimum performance in dual-channel configurations, install identical DDR2 DIMM pairs for each channel. • Install DIMMs with the same CAS latency. To reach the optimum compatibility, obtain memory modules from the same vendor. ※ Usually there is ...
Page 17 - Floppy and IDE Disk Drive Connectors
Hardware Setup 1.8 Connecting Peripheral Devices 1.8.1 Floppy and IDE Disk Drive Connectors The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable. Connect the single end at the longer length of ribbon cable to the FDC1 on the board, the two connectors on the ot...
Page 19 - Make sure the connecting cable bears the same pin assignment.
Hardware Setup 1.8.3 Additional USB 2.0 Port Headers Each header supports 2x additional USB 2.0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis. Pin Pin Assignment Pin Pin Assignment 1 VCC 2 VCC 3 Data0 - 4 Data1 - 5 Data0 + 6 Data1 + 7 Groun...
Page 20 - Front Panel Audio Connection Header; Pin Signal
1.8.5 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. • To use the audio connector at front panel, remove all the jumpers on this header, and then connect to front panel by the extension cable provided with the chassis. • To use the audio co...
Page 21 - Install PCI Express X1 card into slot “PCI-E1”.
Hardware Setup 1.8.6 PCI and PCI Express X1 Slots Install PCI Express X1 card into slot “PCI-E1”. Install PCI cards into slots “PCI1”, “PCI2”, and/or “PCI3”. ※ Slot PCI-E1 will be disabled when slot PCIEX2 is installed. IL9 Pro 1-17
Page 23 - PRESS DEL TO ENTER SETUP
BIOS Setup IL9 Pro 2-1 2. BIOS Setup This motherboard provides a programmable EEPROM so that you can update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and peripherals. Use the BIOS Setup program only when ins...
Page 27 - Multilingual QIG; Multilingual Quick Installation Guide; 規格; Serial ATA; ※ 本手冊的規格與資訊若有變動,恕不另行通知。
Multilingual QIG IL9 Pro 4-3 4. Multilingual Quick Installation Guide 4.1 繁體中文 4.1.1 規格 處理器 • 支援具備 1066MHz 前端匯流排的 Intel Core 2 Duo, Pentium D, Pentium 4, Celeron D 處理器 • 支援 Intel Hyper-Threading 技術 晶片組 • Intel 945P / ICH7 記憶體 • 4 條 240 針腳 DIMM 插槽支援最大 4GB 記憶體容量 • 支援雙通道 DDR2 667 無緩衝非 ECC 記憶 體 網路 • 內建 ...
Page 28 - 快速安裝指南; 本「快速安裝指南」僅包含安裝
4.1.2 快速安裝指南 本「快速安裝指南」僅包含安裝 abit 主機板時 所需的基本硬體資訊。詳細的操作方式，請參 閱完整的手冊版本。 硬體安裝注意事項 • 安裝機板或變換任何設定之前，請先關閉電源並拔掉電源插頭。 • 從抗靜電袋中取出機板前，請先戴上靜電安全手環，以確保自己已確實接地。 • 請握住機板的邊緣。請勿接觸機板上的任何元件。 • 請勿接觸模組及 IC 晶片 • 請將機板置於已接地的抗靜電平面上，或置於隨附的抗靜電袋。 將機板安裝至機殼內 本主機板的電腦機殼應符合以下條件： • 與本主機板的規格相容。 • 機殼上的指示燈及開關支援主機板上的連接線插座。 • 能提供足夠的電力及空間，...
Page 31 - 简体中文; 规格; ATA; 本手册的规格与信息若有变动,恕不另行通知。
Multilingual QIG IL9 Pro 4-7 4.2 简体中文 4.2.1 规格 处理器 • 支持具备 1066MHz 前端总线的 Intel Core 2 Duo, Pentium D, Pentium 4, Celeron D 处理器 • 支持 Intel 超线程技术 芯片组 • Intel 945P / ICH7 内存 • 4 条 240 针脚 DIMM 插槽支持最大 4GB 内存容量 • 支持双信道 DDR2 667 无缓冲非 ECC 内存 网络 • 内建 10/100/1000M 网络控制器 音效 • 支持 7.1 声道 HD 音效 串行 ATA • 4 个 SATA 3...
Page 32 - 快速安装指南; abit
4.2.2 快速安装指南 本“快速安装指南”仅包含基本的硬件信息，供您在安装 abit 主板时进行参考。如需了解高 级操作，请参阅其详细指南。 硬件设置注意事项 • 在安装主板或更改任何设置前，务必关闭电源并从交流插座上拔掉电源线。 • 从防静电袋中取出主板前，应戴上静电安全腕带以使您正确接地。 • 用手拿着主板的边缘。不要触摸主板上的任何元件。 • 不要触摸模块触点和 IC 芯片。 • 将主板放在接地的防静电表面上或者放在主板附带的防静电袋中。 将主板安装到底盘上 此主板的计算机底盘应符合下列条件： • 支持此主板的外形尺寸。 • 支持主板上的所有线缆连接器，能够连接到底盘上的指示灯和开关。...
Page 35 - Appendix
Appendix IL9 Pro 5-1 5. Appendix 5.1 Troubleshooting (How to Get Technical Support?) 5.1.1 Q & A Q: Do I need to clear the CMOS before I use a new motherboard to assemble my new computer system? A: Yes, we highly recommend that you clear the CMOS before installing a new motherboard. Please move ...
Page 37 - absolutely sure
Appendix IL9 Pro 5-3 • Memory configuration: Type in the memory configuration in BIOS setting. Example: Memory Timing: 2.5-3-3-7 @533MHz • Graphics information: Note Graphics card’s brand, model and driver version • Graphics card: Type in the brand and model name of your graphics card. Example: ATI ...
Page 39 - for technical support:
Appendix IL9 Pro 5-5 5.1.3 Contact Information Taiwan Head Office Universal ABIT Co., Ltd. No. 323, Yang Guang St., Neihu, Taipei, 114, Taiwan Tel: 886-2-8751-3380 Fax: 886-2-8751-3381 Sales: [email protected] Marketing: [email protected] North America, South America Universal ABIT (USA) Corporatio...
