Newcon Optik LRB 4000CI - Manual

Page 2 - IMPORTANT INFORMATION; Read prior to activation; At no time should equipment be sent back to Newcon

IMPORTANT INFORMATION Read prior to activation You have just purchased a complicated electronic device. To operate it properly, please read this manual carefully. Here are some common precautions that must be noted. • NEVER subject the unit to impact while operating or being transported • NEVER tran...

Page 3 - Features of the LRB 4000CI Laser Rangefinder Binocular

8. WARRANTY NEWCON OPTIK warrants this product against defects in material and workmanship for one year from the date of the original date of consumer's purchase, but no more than 18 months from the date of manufacturing. If your Newcon product proves to be defective during this period, please bring...

Page 4 - CONTENTS; How can I clear last reading before making next measurement?

CONTENTS 1. Brief description 2. Appearance of the device 3. Supplied accessories 4. Technical characteristics 5. Operation instructions 5.1. Preparing the device for operation 5.2. Measuring procedure 5.3. Mode switching procedure 5.4. Gating distance selection 5.5. Additional display information 5...

Page 6 - Mode 16 is designated to test the display. When you choose

2. APPEARANCE OF THE DEVICE 1 – Eyepieces; 2 – Objective lens – receiving lens; 3 – Objective lens - emitting lens; 4 – Dioptric correction rings; 5 – Mode button; 6 – Action button; 7 – Body of the device; 8 – Rubber grip Fig. 1 6 5.6. Computer interconnectivity The unit is equipped with standard R...

Page 7 - Interpupilary distance adjustment lever

There are four statistical qualifications of the reflected signal: • NO TARGET REFLECTION – when a steady reflected signal isn’t received. Numerical display shows four dashes at the distance displaying area; • TARGET REFLECTION LOW – when the number of steady received reflected signals is just enoug...

Page 8 - TECHNICAL CHARACTERISTICS

7 4. TECHNICAL CHARACTERISTICS 1. Optics Magnification, x Objective Lens, mm Exit Pupil Diameter, mm Field of View Type of Coating Interpupilary distance, mm Diopter adjustment range Axial Resolution, ” Image tilt, maximum - Horizontal - Vertical 7 50 7.1 5 ° Fully multi-coated optics 58-72 ±4 6 60”...

Page 10 - OPERATION INSTRUCTIONS; – Target quality indicator 6 – Laser active indicator; After changing the battery, it is recommended to run the; cLr; button; READY; mode of

5. OPERATION INSTRUCTIONS Liquid Crystal Display (LCD) 1 – Low battery indicator; 2 – Reticle (cross or rectangular selectable); 3 – Units of measurement (Yards, Meters, KMH, MPH, Mils or Degrees); 4 – Measurement result; 5 – Target quality indicator; 6 – Laser active indicator 7 – Over 100m gating ...

Page 11 - Full trek of all possible modes available is depicted on Figure 4.

override reticle type and target selection with the sub selection code. For example, Standard 1 mode implies cross reticle. If you choose rectangular reticle (sub selection code 10), you change the reticle shape and leave all other parameters of this mode intact. If then you choose Standard1 again, ...

Page 13 - Mode switching trek

Fig.4 Mode switching trek Mode Screen display Di st a n c e Sp e e d H o ri zo n tal An g le Ve r ti c a l An g le Re ti c le Ta r g e t Ty p e 1) Standard 1 M Select this mode Go to next mode A , , , Meter Degree Degree 1) Standard 2 M Go to next mode A , , , Meter Mills Mills Codes 3) A M Go into ...

Newcon Optik LRB 4000CI - Manual

Table of Contents:

Summary

Other Newcon Optik Models