Newcon Optik LAM 10M IR - Manual

Page 4 - CONTENTS

1 CONTENTS 1. Brief description ................................................. 2 2. Device design ..................................................... 3 3. DELIVERY SET ................................................ 8 3.1. Standard delivery set ...................................... 8 3.2. Opt...

Page 5 - description

2 Carefully read all the instructions prior to use. Failure to obey the instructions will void the warranty ! INVISIBLE LASER RADIATION CLASS I LASER PRODUCT 830–860 nm 0,1mW. 1. Brief description LAM 10M IR laser aimer (hereinafter referred as LAM) is designed for precise aiming at night time. LAM ...

Page 6 - design

Page 8 - Mode; OFF Off

5 LAM consists of an emitter (6,7, Fig.1), a battery compartment (15,16, Fig.1), windage (9, Fig.1) and elevation (12, Fig.1) adjustment mechanisms, an operating modes switch (17, Fig.1), a remote switch (Fig.2), a clamp (1, Fig.1). A battery is to be inserted into the battery compartment (16, Fig.1...

Page 11 - Standard delivery set; LAM is supplied in the following assembly:; pcs; Optional parts; LAM can be supplied with a barrel mount.

8 3. DELIVERY SET 3.1. Standard delivery set LAM is supplied in the following assembly: Quantity, pcs LAM 10M IR 1 Remote switch 1 Velcro tape 2 O-Ring 1 Case 1 Manual 1 Battery CR123 1 3.2. Optional parts LAM can be supplied with a barrel mount.

Page 13 - INSTRUCTIONS; Installing the battery; screw the battery compartment cap back on.; Mounting LAM on a weapon; align LAM on Picatinny rail,

10 5. OPERATION INSTRUCTIONS 5.1. Installing the battery LAM is powered by a standard Lithium CR123 3V battery. To install a battery: - unscrew the battery compartment cap (15, Fig.1), - insert a battery observing the polarity as marked on the battery compartment, - check the condition of the O-ring...

Page 14 - Connecting the remote control; tighten the union nut,; Adjusting LAM on a weapon; mount LAM on the weapon

11 5.3. Connecting the remote control To connect the remote switch (Fig.2): - unscrew the cap of the remote connector (4, Fig.1) and store it in a safe place, - plug in the remote connector contact (3, Fig.2) observing the key visible on the cable side, - tighten the union nut, - attach the remote s...

Page 16 - General

13 6. Maintenance, storage and transportation 6.1. General LAM is a sophisticated precise optical instrument equipped with electronics. Therefore, it should be handled with due care. - Never disassemble LAM. - Keep away from direct sunlight, impacts, dust, moisture, and sharp changes of temperature....

Page 17 - Storage; relative humidity not higher than 80 % at temperature +25°; To remove old layer of lubricant:; Wipe LAM with clean dry cloth,

14 6.2. Storage To set LAM from combat position into a stowed one: - turn LAM off (operating modes switch (17, Fig.1) should be set to OFF position); - cover emitter tube output window with protective cap (8, Fig.1); - disconnect remote switch (Fig.2) from the weapon, loosen screw caps (13, Fig.1), ...

Page 18 - To apply new layer of lubricant:; Do not cover plastic parts.; Transportation; Turn LAM off by turning operating modes switch.

15 To apply new layer of lubricant: - Within two hours from cleaning apply an even 0.2-0.5 mm thick layer of lubricant on metal surfaces with a brush. - Do not cover plastic parts. When preparing for a long-term storage LAM just received from manufacturer or from workshop, ensure that actual set is ...

Page 21 - NEWCON OPTIK; warrants this product against defects in; NEWCON; is not responsible for warranty service should the

18 8. WARRANTY NEWCON OPTIK warrants this product against defects in material and workmanship for one year from the date of the original date of consumer's purchase. Should your Newcon product prove defective during this period, please bring the product securely packaged in its original container or...

Page 22 - SUPPORT; US Customers

19 9. CUSTOMER SUPPORT Should you experience any difficulties with your NEWCON OPTIK product, consult the enclosed manual. If the problem remains unresolved, contact our customer support department at +1(416) 663-6963 or toll free at 1-877-368-6666. Our operating hours are 9am-5pm, Monday - Friday, ...

Page 23 - CERTIFICATE

20 10. QUALITY CERTIFICATE LAM10M IR serial number: ________________________________________________ complies with all technical specifications and has passed the quality inspection. Date of production: _________________________________ Quality Inspector: __________________________________ Quality A...

Newcon Optik LAM 10M IR - Manual

Table of Contents:

Summary

Other Newcon Optik Models