NewAir AC 12000E - Manual - manualsarea.com

Page 2 - BEFORE USE; GENERAL SAFETY INSTRUCTIONS:; DO NOT PLACE OBJECTS ON THE UNIT, AND DO; WALL

BEFORE USE GENERAL SAFETY INSTRUCTIONS: • ALWAYS OPERATE THE UNIT IN AN UPRIGHT POSITION AND PLACE IT ON A FLAT, LEVEL SURFACE AT LEAST 14 INCHES AWAY FROM ANY OTHER OBJECTS (Fig 1 & 4). • DO NOT PLACE OBJECTS ON THE UNIT, AND DO NOT COVER OR OBSTRUCT THE INLET OR OUTLET GRILLS (FIG. 2). • CLOSE...

Page 3 - PARTS LIST; filter

PARTS LIST Front: Back: 1. Control panel 2. Louvers 3. Carrying handle 4. Casters 5. Air filter 6. Air inlet 7. Cord storage 8. Exhaust air outlet 9. Rubber plug / drainage point Accessories: 10. Exhaust hose 11. Hose adaptor (goes over the hose and into the window kit) 12. Extendable window kit 13....

Page 4 - INSTALLATION INSTRUCTIONS; Installing the Exhaust Hose and Window Kit:; Wall or Window; Adapter; Open the window and insert the window kit into the open gap.

INSTALLATION INSTRUCTIONS Installing the Exhaust Hose and Window Kit: FIG.5 Wall or Window Window Kit Adapter 1. Open the window and insert the window kit into the open gap. 2. Close the window until the window kit is held securely. This technique may also be used for sash windows. 3. Fit the exhaus...

Page 5 - Positioning the Exhaust Hose:; The included exhaust hose is

Positioning the Exhaust Hose: • Insert the exhaust hose into the back of the unit and tighten it into place. • Avoid kinks and bends in the exhaust hose. This can cause moist air to accumulate, resulting in overheating and • The exhaust hose may be extended from 12 inches (300 mm) to 59 inches (1500...

Page 6 - R e a tta ch th e filte r o n to th e

Installing the Activated Carbon Filter: 1. Remove the filter frame from the unit. 2. Separate the filter from the filter frame. 3. Remove the activated carbon filter from its plastic bag. 4. Insert the activated carbon filter into the filter frame. 5. 6. Insert the filter set into the unit. 5 FIG.11...

Page 7 - OPERATING INSTRUCTIONS; Control Panel; on low fan speed. The default temperature is 75; F to

OPERATING INSTRUCTIONS Control Panel 1. Fan speed (ventilation) button 2. Timer button 3. Display window 4. Remote control receiver 5. Heater indicator (for AC-12000H only ) 6. Mode selection button 7. Automatic mode indicator 8. Cooling mode indicator 9. Fan mode indicator 10. Temperature increase ...

Page 8 - Setting the Temperature:; on the first hour, another 1

Setting the Mode/Function: 1. Press the MODE button to select the desired mode (cooling, fan or heating). Heating mode is only available on the AC-12000H. 2. The selected mode’s indicator light will turn on. Setting the Temperature: 1. Press the “Up” or “Down” button to change the set temperature. 2...

Page 9 - your immediate area.; The exhaust pipe will still need to be fitted onto the unit in order; . When in heating mode, the machine can be set on HIGH

Heating Mode: When the air conditioner is in heating mode, ambient warm air is recycled and used to heat your immediate area. The exhaust pipe will still need to be fitted onto the unit in order for the cold air to be removed . When in heating mode, the machine can be set on HIGH or LOW speed. Ioniz...

Page 10 - DRAINING THE UNIT; To resume cooling, empty the reservoir by following these steps:; Repeat these steps until the water; Water hole

DRAINING THE UNIT During the cooling process, some water will be extracted from the air and stored within the unit’s water reservoir. If the water reservoir is full, both the compressor and motor will stop and the unit will beep (press any button to stop the beeping sound). The full water tank indic...

Page 11 - For Continuous Drainage:; The drain tube may be extended; Drain knob; Drain tube

For Continuous Drainage: • Remove the rubber plug from the drainage port and retain it for future use. • Connect the drain tube to the drainage port as shown (fig. 17). • Connect the other end of the hose to a drain. FIG.16 • The drain tube may be extended by adding an extension tube with a suitable...

Page 13 - MAINTENANCE INSTRUCTIONS; Cleaning the Housing:; Cord wrap

MAINTENANCE INSTRUCTIONS Always unplug the air conditioner from the power supply before cleaning. To maximize the efficiency of the air conditioner, regularly clean the unit. Cleaning the Housing: • Use a soft, damp cloth to wipe the body clean. • Never use harsh chemicals, gasoline, detergents, che...

Page 14 - TROUBLESHOOTING; can void your warranty and endanger the user.

TROUBLESHOOTING The air conditioner does not work. y Is the air conditioner plugged in? y Is the power outlet functioning correctly? y Is the full water tank indicator light flashing? y Is the ambient room temperature lower than the set temperature? The unit does not produce adequate cooling. y Is t...

Page 15 - TECHNICAL SPECIFICATIONS; to the rating label found on the back of the unit.

TECHNICAL SPECIFICATIONS Model Number: AC-12000E AC-12000H Power Consumption for Cooling* 1166W / 11A 1166W/11A Power Consumption for Heating * N/A 1054W/10.1A Air Volume (max. speed) 440m 3 /h 440m 3 /h Dehumidification Capacity 1.2L/hour 1.2L/hour Voltage / Frequency 115V, 60Hz Compressor Type Rot...

Page 16 - LIMITED MANUFACTURER’S WARRANTY; Power failure

LIMITED MANUFACTURER’S WARRANTY This appliance is covered by a limited manufacturer’s warranty. For one year from theoriginal date of purchase, the manufacturer will repair or replace any parts of this appliancethat prove to be defective in materials and workmanship, provided the appliance has beenu...

NewAir AC 12000E - Manual

Table of Contents:

Summary

Other NewAir Models