NewAir 8625 - Manual
NewAir 8625 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – IMPORTANT SAFETY INFORMATION WARNING:; Recycling Thermostat; Wiring Table; Old Terminal
- Page 3 – Figure 1; Installing Item 8625 Thermostat; Figure 2
- Page 4 – To Test Thermostat; Figure 3
- Page 5 – Wiring Diagrams
- Page 6 – CAUTION: DO NOT SWITCH SYSTEM TO COOL IF THE TEMPERATURE
- Page 7 – Programming Guide; AM; PROGRAMMING YOUR THERMOSTAT; Cursor
- Page 8 – CUSTOMIZING THE THERMOSTAT
- Page 9 – EER; Begin Programmed Operation
- Page 10 – CHECK FILTER; Reset
- Page 11 – Troubleshooting; Symptom; If problems with thermostat cannot be resolved, call:; automated help line is available.
- Page 12 – TWO-YEAR LIMITED WARRANTY; Climate Controls Americas; warrants to the original contractor; Climate; Climate Controls Americas; agrees to repair or replace at its option; Climate; Climate Controls Americas; shall not be liable
1
Application
The Robertshaw 8625 is a multi-stage thermostat designed to control
24 VAC heat pump systems.
Features
• Large back lit display.
• Four preprogrammed E
NERGY
S
TAR
®
setpoints for each day of the week.
• Adjustable 1
st
stage temperature differential: 1.0°F to 3.0°F (0.5°C to
1.5°C).
• Adjustable 2
nd
stage temperature differential: 1.0°F to 6.0°F (0.5°C to
3.0°C).
• Adjustable 2
nd
stage delay (10-40 minutes).
• Energy Efficient Recovery (EER™).
• Residual cooling for added air conditioning efficiency.
• Zone compatible as master thermostat.
• Fahrenheit/Celsius display option.
• Programmable from 45°F (4°C) to 90°F (32°C).
• Accuracy within ± 1 degree.
• Separate heating and cooling programs.
110-1101
5 - 2 Day Programmable
2 Heat / 2 Cool
User’s Manual
Quick Start
Installation and
Programming
W
A R R A N T Y
2
TW
O YEAR
D I G I TA L
P R O G R A M M A B L E
T H E R M O S TAT
862
5
E L E C T R I C
E
G A S
G
O I L
O
®
NeW
H E AT P U M P
H
As an E
NERGY
S
TAR
®
partner, Climate Controls Americas has determined
that this thermostat product meets the E
NERGY
S
TAR
®
guidelines for
energy efficiency.
110-1101 7/22/04 8:16 AM Page 1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
IMPORTANT SAFETY INFORMATION WARNING: • Always turn off power at main fuse or circuit breaker panel before installing, removing, cleaning, or servicing thermostat. • Read all the information in this manual before installing this thermostat. • DO NOT CONNECT TO 120 VAC. This is a 24 VAC low-voltage t...
IMPORTANT SAFETY INFORMATION WARNING: In heat pump applications, do not connect anything to the W1terminal. When switched to HP mode, W1 is connected internallyto Y1 on the thermostat. Connect AUX heat to the W2/E terminal. 1. Turn off power to heating and cooling system. 2. Remove cover of old ther...
6. Mark placement of mounting holes (see Figure 3). Set base aside. 7. Drill the marked holes using a 3/16” (5mm) drill bit. NOTE: Enclosed plastic anchors do not require a drilled hole for drywall. 8. Tap plastic anchors into the wall. 9. Align base with plastic anchors and feed wires through openi...
