National Instruments 6008 - Manual
National Instruments 6008 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Feature
- Page 3 – Safety Guidelines; Caution
- Page 5 – Software; for USB Devices Getting Started Guide; for more information.; LabVIEW SignalExpress for DAQ; Start»All Programs»National Instruments»
- Page 6 – Hardware
- Page 7 – Setting Up Hardware; Complete the following steps to set up the hardware:
- Page 8 – Note
- Page 9 – Module
- Page 10 – GND
- Page 12 – MUX
- Page 13 – PGA; terminal, and the negative lead to the AI– terminal.
- Page 15 – Connecting Reference Single-Ended Voltage Signals; Digital Trigger
- Page 16 – Analog Output; DACs
- Page 17 – Minimizing Glitches on the Output Signal; for more information about minimizing; Digital I/O Circuitry
- Page 18 – Source/Sink Information
- Page 19 – Static DIO; Event Counter; Specifications
- Page 20 – Reference and Power Sources; External References; V reference voltage can be used as a signal for self test.; V Power Source; Analog Input; software selectable
- Page 22 – at full scale; Range
- Page 23 – External Voltage; to 5 V; Level
- Page 24 – USB; Physical Characteristics; If you need to clean the module, wipe it with a dry towel.
- Page 25 – Safety; Voltages; Connect only voltages that are within these limits.; Hazardous Locations
- Page 26 – Electromagnetic Compatibility; EN 61326 EMC requirements Minimum Immunity; CE Compliance; in the Certification column.; Waste Electrical and Electronic Equipment (WEEE); EU Customers
- Page 27 – Where to Go for Support; you have access to everything from
USER GUIDE AND SPECIFICATIONS
NI USB-6008/6009
This guide describes how to use the National Instruments USB-6008/6009
data acquisition (DAQ) devices and lists specifications.
Introduction
The NI USB-6008/6009 provides connection to eight analog input (AI)
channels, two analog output (AO) channels, 12 digital input/output (DIO)
channels, and a 32-bit counter with a full-speed USB interface.
Note
This manual revision updates naming conventions to reflect the conventions used in
NI-DAQmx. Table 1 notes the correlation between the old and updated names.
Table 1.
Digital Output Driver Type Naming Conventions
Hardware Functionality
NI-DAQmx Terminology
Open-drain
Open collector
Push-pull
Active drive
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
NI USB-6008/6009 User Guide and Specifications 2 ni.com Figure 1. NI USB-6008/6009 Figure 2. NI USB-6008/6009 Back View Table 2. Differences Between the NI USB-6008 and NI USB-6009 Feature NI USB-6008 NI USB-6009 AI Resolution 12 bits differential, 11 bits single-ended 14 bits differential, 13 bits ...
© National Instruments Corporation 3 NI USB-6008/6009 User Guide and Specifications Safety Guidelines Caution Operate the hardware only as described in these operating instructions. The following section contains important safety information that you must follow when installing and using the NI USB-...
© National Instruments Corporation 5 NI USB-6008/6009 User Guide and Specifications Software Software support for the NI USB-6008/6009 for Windows 2000/XP/Vista is provided by NI-DAQmx. The NI-DAQmx CD contains example programs that you can use to get started programming with the NI USB-6008/6009. R...
