Page 2 - prOpOsitiOn 65 WarninG
page 2 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) prOpOsitiOn 65 WarninG Engine exhaust and some of its constituents, and some dust created of California to cause cancer, birthdefects and other reproductive harm. by power sanding, sawing, grinding, drilling and other const...
Page 3 - SILICOSIS WARNING; silicOsis/respiratOry WarninGs
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 3 Grinding/cutting/drilling of masonry, concrete, metal andother materials with silica in their composition may giveoff dust or mists containing crystalline silica. Silica is abasic component of sand, quartz, brick clay, gra...
Page 4 - table Of cOntents; plaster and Mortar Mixers; component drawings; NOTICE
page 4 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) table Of cOntents WM63H5/WM63H8/WM63e plaster and Mortar Mixers Proposition 65 Warning ........................................... 2 Silicosis/Respiratory Warnings ................................ 3 Table Of Contents .........
Page 5 - parts OrderinG prOcedures; Ordering parts has never been easier!; choose from three easy options:; we aCCepT all maJor CrediT Cards!; order via internet; Order; internet; order via Fax; Fax
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 5 parts OrderinG prOcedures www .multiquip .com Ordering parts has never been easier! choose from three easy options: we aCCepT all maJor CrediT Cards! When ordering parts, please supply: ❒ dealer account number ❒ dealer nam...
Page 6 - safety infOrMatiOn; saFeTY messages; danger; Lethal exhaust gas hazards; Symbol
page 6 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) safety infOrMatiOn Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messag...
Page 7 - general saFeTY
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 7 safety infOrMatiOn general saFeTY CauTion never operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices r...
Page 8 - mixer saFeTY
page 8 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) safety infOrMatiOn mixer saFeTY danger never operate the equipment in an explosive atmosphere or near combustible materials. An explosion or fi re could result causing severe bodily harm or even death. do noT mix fl amm...
Page 9 - generaTor saFeTY; power Cord/Cable safety; TransporTing saFeTY
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 9 safety infOrMatiOn Fuel saFeTY (gasoline models onlY) danger do noT start the engine near spilled fuel or combustible fl uids. Fuel is extremely fl ammable and its vapors can cause an explosion if ignited. alwaYs refue...
Page 10 - Towing saFeTY; Department of; environmenTal saFeTY
page 10 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) safety infOrMatiOn Towing saFeTY CauTion Check with your local county or state safety towing regulations, in addition to meeting Department of Transportation (DOT) Safety Towing Regulations, before towing your mixer. I...
Page 11 - Tow Bar To mixer ConneCTion; Figure 1. Tow Bar and Safety Chain Installation; CauTion; safety cHain cOnnectiOn
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 11 Tow Bar To mixer ConneCTion Reference Figure 1 for the installation of the safety chain.1. Insert the tow bar through the round opening at the bottom of the mixer stand. Align the hole on the tow bar with the hole on the ...
Page 12 - specificatiOns; Table 1. mixer specifications
page 12 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) specificatiOns Table 1. mixer specifications Capacity 6.3 cu. ft (178 liters) Bag Capacity 1-1/2 to 2-1/2 bags weight 574 lbs. (260 kg.) Height w/dump Handle 73 in. (185 cm.) discharge Height 17.5 in. (44.4 cm.) drive V-Be...
Page 13 - diMensiOns; description; Width
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 13 diMensiOns Figure 3. Dimensions B C A HBC-1 2-INCH BALL COUPLER HPC-1 1-INCH PIN COUPLER OPTIONAL TOW BARS APPROXIMATE LENGTH 36 IN. (91.44 CM) HLC-1 LOOP COUPLER Table 3. dimensions description dimensions in. (cm) Length...
Page 14 - General infOrMatiOn; appliCaTion; Table 4. Hardware Torque recommendations
page 14 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) General infOrMatiOn appliCaTion The MQ Whiteman WM63 Series mixers (drum capacity of 6.3 cu. ft./178 liters) are shipped completely assembled and have been factory tested and are ready for use.This mixer is only intended f...
Page 15 - cOMpOnents; Figure 4. Mixer Components; right
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 15 cOMpOnents Figure 4 illustrates the basic components and controls of the WM63 Series mixer. Figure 4. Mixer Components 1. Tires ply — The tire ply (layers) number is rated in letters. This mixer uses 13-inch 4-ply tires. ...
Page 16 - inspectiOn; BeFore sTarTing; UPPER LIMIT; season; Summer
page 16 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) inspectiOn BeFore sTarTing 1. Read all safety instructions at the beginning of manual.2. Clean the unit, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air filte...
Page 17 - oil soaked; Blade CHeCk; PULL OUT; Figure 9. Blade Inspection
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 17 inspectiOn v-BelT CHeCk Visually examine the V-belt (Figure 7) and determine if it is full of tiny cracks, frayed, has pieces of rubber missing, is peeling or otherwise damaged.Also, examine the belt and determine if it i...
Page 18 - Figure 11. Engine Components; iniTial serviCing; basic enGine
page 18 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) Figure 11. Engine Components iniTial serviCing The engine (Figure 11) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the engine manufacturer’s manual for instructions and details o...
Page 19 - electric MOtOr; eleCTriC moTor; Figure 12. Single Phase Electric Motor With; Table 6. electric motor wiring information
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 19 electric MOtOr eleCTriC moTor For maintenance care and operation of the electric motor, refer to your electric motor instruction booklet furnished with the motor.Protect the electric motor from dust as much as possible an...
Page 20 - eleCTriC moTor volTage swiTCH; alwaYs; Table 7. recommended extension Cord sizes
page 20 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) The electric motor supplied is wired for 115 VAC grounded operation. Make certain that the correct size grounded (3-wires) extension cord is used. See Table 7 below. Motors can burn out when the line voltage falls 10% belo...
Page 21 - paddle blade adjustMent; Adjust paddles as shown in Figure 13.; Figure 13. Paddle Blade Adjustment; DRUM END
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 21 paddle blade adjustMent Adjust paddles as shown in Figure 13. Figure 13. Paddle Blade Adjustment TOW ENDCAST PADDLE ENGINE ENDCAST PADDLE CENTER ENGINE END CAST PADDLE SIDE PADDLE BLADE END P ADDLE BLADE ROTATION ROT A TI...
Page 22 - do noT; Figure 15. Choke Lever; warning; Figure 16. Throttle Lever
page 22 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) start-up This section is intended to assist the operator with the initial start-up of the unit. It is extremely important that this section be read carefully before attempting to use the mixer in the field. do noT use your...
Page 23 - Figure 19. Belt Slip Lever; Figure 22. Starter Grip
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 23 start-up 6. Place the belt slip lever (Figure 19) in the START/STOP (disengaged) position. Figure 19. Belt Slip Lever (Start/Stop Position) Figure 20. Drum Lock Pin (Side-View) BELT SLIP LEVER START/STOP POSITION CauTion ...
Page 24 - OperatiOn; Figure 25. Stand Clear of Dump Handle
page 24 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) OperatiOn mixing/dumping 1. The paddle shaft inside the drum should be rotating at this time. 2. Add a small amount water to the mixing drum. 3. Lift the mixing bag compound onto the steel safety grate over the bag cutter ...
Page 25 - nOtes
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 25 nOtes
Page 26 - Table 8. engine maintenance schedule
page 26 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) Maintenance (enGine) Use Table 8 as a general maintenance guideline when servicing your engine. For more detail engine maintenance information, refer to the engine owner’s manual supplied with your engine. Table 8. engine ...
Page 27 - Figure 26. Spark Plug Gap; engine oil; GAP; engine air Cleaner; Figure 28. Engine Air Cleaner
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 27 Maintenance (enGine) Perform the scheduled maintenance procedures as defined by Table 8 and below: dailY Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as nece...
Page 29 - wHeel Bearings; Figure 32. Wheel Hub and Bearings; main gear and drive pinion alignmenT; Figure 33. Drive Pinion and Main Gear; inspeCT TooTH ConTaCT BeTween main gear
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 29 Maintenance (Mixer) Figure 31. Grease Fittings (Countershaft) wHeel Bearings 1. After every 3 months of operation, remove the hub dust cap and inspect the wheel bearings (Figure 32). Once a year, or when required, disasse...
Page 30 - Figure 34. Gear Teeth Alignment; gear luBriCaTion; Figure 35. Pinion and Bull Gear Lubrication; g r e a s e F i T T i n g s ( Z e r k ) m a i n T e n a n C e; MAIN; Figure 36. Grease Fittings Electric Motor
page 30 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) 4. If gear teeth are not contacting properly (Figure 34), adjust pillow block to correct the problem. Figure 34. Gear Teeth Alignment gear luBriCaTion The surface of the pinion and main gear (Figure 35) should be very ligh...
Page 31 - lug nut Torque requirements; Table 9. Tire wear Troubleshooting; never; Figure 37. Wheel Lug Nuts Tightening
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 31 Maintenance (Mixer) lug nut Torque requirements It is extremely important to apply and maintain proper wheel mounting torque. Be sure to use only the fasteners matched to the cone angle of the wheel. Proper procedure for ...
Page 32 - suspension; Figure 38. Axle Support Components; mixer Cleaning; Figure 39. No Spraying of Water; CRUSH HAZARD AREA. KEEP HANDS
page 32 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) Maintenance (Mixer) suspension The rigid type axle and associated hardware (Figure 38) should be periodically inspected for signs of excessive wear, elongation of bolt holes, and loosening of fasteners. Replace all damaged...
Page 33 - mixer sTorage
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 33 Maintenance (Mixer) mixer sTorage For storage of the mixer for over 30 days, the following is recommended: Drain the fuel tank completely, or add STA-BIL to the fuel. Run the engine until the fuel is completely consum...
Page 34 - trOublesHOOtinG; symptom
page 34 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) trOublesHOOtinG Troubleshooting (engine) symptom possible problem solution Diffi cult to start, fuel is available, but no spark at spark plug. Spark plug bridging? Check gap, insulation or replace spark plug. Carbon deposi...
Page 36 - mixer Troubleshooting
page 36 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) mixer Troubleshooting Blades will not rotate. Worn or defective V-belt? Replace V-belt. Adjustment lever mis-aligned? Check position of adjustment lever. Adjust if necessary. Material leaking from drum ends. Worn or defect...
Page 37 - WirinG diaGraM
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 37 WirinG diaGraM
Page 38 - explanatiOn Of cOde in reMarks cOluMn; sample parTs lisT; remarks Column
page 38 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) explanatiOn Of cOde in reMarks cOluMn The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any qu...
Page 39 - suGGested spare parts; wm63-series plasTer and morTar mixer wiTH
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 39 suGGested spare parts wm63-series plasTer and morTar mixer wiTH Honda gx160uT1Hx2/gx240uT1Ha2 engines and 1.5 Hp eleCTriC moTor. 1 to 3 units Qty. p/n description 6............491107 .................. V-BELT A32, HONDA E...
Page 40 - naMeplate and decals
page 40 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) naMeplate and decals MODEL SERIAL P/N 521232 CAUTION 1. Use manufacturer’s recommended torque values when tightening wheel lug nuts. 2. Use recommended tire pressure values when inflating tires. exceed recommended tire pre...
Page 42 - OPTIONAL TOW BARS
page 42 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) fraMe assy. MOUNT PILLOW BLOCKS FOR PINION SHAFT HERE MOUNT DRUM BEARING HERE MOUNT DRUM BEARING HERE OPTIONAL TOW BARS A A 1 2 10 3 4 6 7 8 5 11 12 13 15 16 17 18 9 CHAIN & LINK KIT 14 14A
Page 45 - PADDLE SHAFT
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 45 paddle sHaft assy. no. parT no. parT name QTY. remarks 1 514752 PADDLE SHAFT 1 2 492584 NUT, LOCK 1/2" 6 3 530140C PADDLE ARM, CENTER ENGINE END 1 4 3215 SCREW, HHC 1/2-13 X 3-1/2 2 5 EM200292 INSERT, PADDLE ARM 4 6 5...
Page 48 - druM and paddle sHaft cOMplete assy.
page 48 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) druM and paddle sHaft cOMplete assy.
Page 49 - parT name
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 49 druM and paddle sHaft cOMplete assy. no. parT no. parT name QTY. remarks 1 516069 DRUM AND SHAFT COMPLETE ASSY. ...........1.......... INCLUDES ITEMS LISTED BELOW 530028 DRUM BEARING BRACKET 2 3249 CAP, DUST 1 20561-001 B...
Page 57 - RUBBER PROTECTOR
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 57 cabinet assy. no. parT no. parT name QTY. remarks 1 515014 CABINET, ENGINE W/DECALS ........................1................INCLUDES ITEMS W/$ 2 490202 RUBBER PROTECTOR 4 3$ 13287 LOCK NUT 8-32 6 4$ 2203 WASHER, FLAT #10...
Page 58 - terMs and cOnditiOns Of sale — parts
page 58 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12) terMs and cOnditiOns Of sale — parts paYmenT Terms Terms of payment for parts are net 30 days. FreigHT poliCY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O...
Page 60 - OperatiOn and parts Manual; Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; United StateS; Canada
OperatiOn and parts Manual Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING United StateS Multiquip Corporate Office MQ Parts Department 18910 Wilmington Ave. Carson, CA 90746 Contact: [email protected] Tel. (800) 421-1244 Fax (310) 537-3927 80...
