Page 2 - PROPOSITION 65 WARNING
PAGE 2 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) Engine exhaust and some of its constituents, and some dust created of California to cause cancer, birthdefects and other reproductive harm. by power sanding, sawing, grinding, drilling and other construction activi...
Page 3 - SILICOSIS WARNING; SILICOSIS/RESPIRATORY WARNINGS
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 3 Grinding/cutting/drilling of masonry, concrete, metal andother materials with silica in their composition may giveoff dust or mists containing crystalline silica. Silica is abasic component of sand, quartz, brick c...
Page 4 - TABLE OF CONTENTS; Specifications and part numbers are; Component Drawings
PAGE 4 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) TABLE OF CONTENTS Specifications and part numbers are subject to change without notice . In accordance with our established policy ofconstant improvement, we reserve the right toamend these specifications at any ti...
Page 5 - PARTS ORDERING PROCEDURES; Ordering parts has never been easier!; Choose from three easy options:; Order via Internet; Order; Order via Fax
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 5 PARTS ORDERING PROCEDURES www .multiquip .com Ordering parts has never been easier! Choose from three easy options: WE ACCEPT ALL MAJOR CREDIT CARDS! When ordering parts, please supply: R Dealer Account Number R De...
Page 6 - SAFETY; DANGER
PAGE 6 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) FOR YOUR SAFETY AND SAFETY OF OTHERS! Safety precautions should be followed at alltimes when operating this equipment. Failureto read and understand the Safety Messagesand Operating Instructions could result in inj...
Page 8 - RULES AND REGULATIONS; GENERAL SAFETY; DEATH; ! This equipment is to be
PAGE 8 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) RULES AND REGULATIONS NEVER touch the hot exhaust manifold, muffler or cylinder. Allow these parts to coolbefore servicing engine or pump. ALWAYS allow the engine to cool before adding fuel or performing servic...
Page 9 - TRANSPORTING
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 9 RULES AND REGULATIONS When towing, an adequate safety chain must befastened to the frame. See Towing Guidelines section inthis manual. Keep all inexperienced and unauthorized people away from the equipment at a...
Page 10 - EMERGENCIES
PAGE 10 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) EMERGENCIES ALWAYS know the location of the nearest fire extinguisher. ALWAYS know the location of the nearest first aid kit. In emergencies, always know the location of the nearest phone or keep a phone on ...
Page 11 - TOWING GUIDELINES; TOWING SAFETY PRECAUTIONS
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 11 TOWING GUIDELINES TOWING SAFETY PRECAUTIONS The following list of suggestions should be used when towingthe mixer: Check with your county or state safety towing regulationsdepartment before towing your mixer . ...
Page 12 - safety chain; TOW BAR TO MIXER CONNECTION; Figure 1. Tow Bar and Safety Chain Installation; CAUTION — Tow With Safety Chain; SAFETY CHAIN CONNECTION
PAGE 12 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) Reference Figure 1 for the installation of the safety chain . TOW BAR TO MIXER CONNECTION 1. Insert the tow bar through the round opening at the bottom of the mixer stand. Align the hole on the tow bar with the ho...
Page 13 - SPECIFICATIONS
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 13 SPECIFICATIONS r e x i M s n o i t a c i f i c e p S 1 e l b a T l e d o M r e x i M y t i c a p a C m u r D ) s r e t il ( t f . u c y t i c a p a C m u r D ) . g k 2 4 ( . s b l 4 9 d n a l t r o P g a B t n e m...
Page 14 - DIMENSIONS
PAGE 14 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) Figure 2. Dimensions DIMENSIONS s n o i s n e m i D . 3 e l b a T n o i t p i r c s e D ) . m c ( . n i s n o i s n e m i D h t g n e L ) . m c 3 1 2 ( . n i 4 8 h t d i W ) . m c 2 4 1 ( . n i 6 5 t h g i e H ) ....
Page 15 - GENERAL INFORMATION; Application
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 15 GENERAL INFORMATION Application The MQ WM120 series hydraulic mixers (drum capacity12.0 cu. ft./340 liters) are shipped completely assembledand have been factory tested and are ready for use. This mixer is only in...
Page 16 - MIXER COMPONENTS
PAGE 16 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) MIXER COMPONENTS Figure 3. Mixer Components (Wheels) Figures 3 and 4 illustrate the basic components and controlsof the WM120 series hydraulic mixer 1. Tires — Replace with manufacturer recommeded tires only. This...
Page 17 - MIXER COMPONENTS/HYDRAULIC COMPONENTS; HYDRAULIC COMPONENTS; Figure 5. Hydraulic Components
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 17 MIXER COMPONENTS/HYDRAULIC COMPONENTS 17. Adjustable Stabilizer Jack Stands — Use these jack stands (3) to adjust the mixer to the desired height. 18. Forklift Pockets — When lifting of the mixer is required, use ...
Page 18 - ENGINE COMPONENTS; Figure 6. Engine Controls and Components; INITIAL SERVICING; DANGER — Explosive Fuel Hazards
PAGE 18 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) ENGINE COMPONENTS Figure 6. Engine Controls and Components INITIAL SERVICING The engine (Figure 6) must be checked for proper lubricationand filled with fuel prior to operation. Refer to themanufacturers engine ma...
Page 19 - ELECTRIC MOTOR COMPONENTS; ELECTRIC MOTOR; CAUTION; spray water at any time on the; DO NOT; operate electr ic motor in an explosive; Electric Motor Connection; Figure 7. Electric Motor
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 19 ELECTRIC MOTOR COMPONENTS ELECTRIC MOTOR For lubrication care and operation of the electric motor,refer to your electric motor instruction booklet furnishedwith the motor. Protect the electric motor from dust as m...
Page 20 - Adjust paddles as shown in Figure 8.
PAGE 20 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) Figure 8. Paddle Blade Adjustment (Steel Drum) Adjust paddles as shown in Figure 8. PADDLE BLADE ADJUSTMENT (STEEL DRUM)
Page 21 - Adjust paddles as shown in Figure 9.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 21 Adjust paddles as shown in Figure 9. PADDLE BLADE ADJUSTMENT (POLY DRUM) Figure 9. Paddle Blade Adjustment (Poly Drum)
Page 22 - INSPECTION; BEFORE STARTING; li; FUEL CHECK
PAGE 22 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) INSPECTION This section is intended to assist the operator with theinspection of the hydraulic mixer. It is extremely importantthat this section be read carefully before attempting to usethe mixer in the field. DO...
Page 23 - HYDRAULIC OIL; If your unit has hydraulic dump capability, check the; Figure 12. Hydraulic Oil Sight Gauge; BLADE CHECK; dump handle to the drum in towing position.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 23 INSPECTION HYDRAULIC OIL Check hydraulic oil sight gauge (Figure 12) to ensure thathydraulic oil is at the midway level. HYDRAULIC HOSES Check hydraulic hoses to make sure they are not worn,frayed or defective. GR...
Page 24 - STARTING THE ENGINE; ON; Figure 18. Throttle lever Lever; CLOSED; Located on the engine cover is the; starter grip; Figure 17. Choke Lever; Figure 21. Starter Grip
PAGE 24 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) INITIAL START-UP (GASOLINE) STARTING THE ENGINE The following steps outline the procedure for starting theengine. Depending on the type of engine employed in themixer the steps may vary slightly. If your mixer has...
Page 25 - STARTING THE ELECTRIC MOTOR; MIXING; WARNING — Dump Handle Safety; Figure 23. Hydraulic Paddle Lever; drum lock lever
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 25 INITIAL START-UP (ELECTRIC)/OPERATION STARTING THE ELECTRIC MOTOR 1. Using an adequate size extension cord (Table 7), connect one end of the extension cord to the plug onthe electric motor, connect the other end t...
Page 26 - OPERATION; vertical; Figure 27. Hydraulic Dump Lever
PAGE 26 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) OPERATION DUMPING (MANUAL) 1. Release drum lock lever by pushing lever into vertical position (Figure 25). 2. Pull dump handle downward to discharge (empty) the drum. Move dump handle upward to return it to ver ti...
Page 29 - warm; Figure 32. Spark Plug Gap; ENGINE AIR CLEANER; NEVER; Figure 34. Engine Air Cleaner
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 29 MAINTENANCE Perform the scheduled maintenance procedures as definedby Table 8 and below: Daily ■ Thoroughly remove dirt and oil from the engine andcontrol area. Clean or replace the air cleaner elementsas necessar...
Page 30 - Figure 37. Hydraulic Oil Filter
PAGE 30 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) DRUM HEAD SEALS There is 1 set of drum head seals (Figure 35) that will requirelubrication. Lubricate the grease fitting for each drum seal after each use using any grade lithium base grease. Apply grease until vi...
Page 31 - TABLE 9. TIRE WEAR TROUBLESHOOTING; LUG NUT TORQUE REQUIREMENTS
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 31 TIRES/WHEELS/LUG NUTS Tires and wheels are a ve ry impor tant and cr iticalcomponents of the trailer. When specifying or replacingthe trailer wheels it is important the wheels, tires, and axleare properly matched....
Page 32 - Figure 40. Axle Support Components
PAGE 32 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) MAINTENANCE (MIXER) 3. After first road use, retorque all lug nuts in sequence. Check all wheel lug nuts periodically. SUSPENSION The suspension type axle and associated hardware (Figure40) should be periodically ...
Page 33 - Figure 41. No Spraying of Water; MIXER STORAGE; WARNING — Disengaged Drum Lock
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 33 MAINTENANCE (MIXER)/STORAGE WARNING — Keep Hands Clear of Drum When rotating the mixing drum from the dump positionto the upright position, keep hands clear of safety grate. The possibility exists of hands or fing...
Page 34 - and; Electric Motor
PAGE 34 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of abreakdown, please take a remedial action following the diagnosis based on the Engine , Mixer and Ele...
Page 37 - Figure 43. Electric Motor Wiring Diagram; GROUNDING
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 37 Figure 43. Electric Motor Wiring Diagram WIRING DIAGRAM (ELECTRIC MOTOR) WHITE/NEUTRAL G L6-30P TWIST-LOCK 2-POLE/3-WIRE GROUNDING X BLACK/LINE Y GREEN/GROUND WHITE/NEUTRAL G L16-20P TWIST-LOCK 3-POLE/4-WIRE GROUN...
Page 38 - HYDRAULIC SYSTEM DIAGRAM; Figure 44. Hydraulic System Diagram
PAGE 38 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) HYDRAULIC SYSTEM DIAGRAM CYLINDER RELIEF VALVE 1750 PSI GEAR PUMP POWER TANK SUCTION STRAINER HYDRAULIC DUMP FORWARD/REVERSE TANK RETURN FILTER BYPASS 25 PSI HYD MOTOR 1 2 RELIEF VALVE 1750 PSI HYDRAULIC SYSTEM DI...
Page 39 - NOTES
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 39 NOTES
Page 40 - EXPLANATION OF CODE IN REMARKS COLUMN; SAMPLE PARTS LIST; REMARKS Column
PAGE 40 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there a...
Page 41 - SUGGESTED SPARE PARTS
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 41 SUGGESTED SPARE PARTS WM120PS 1 TO 3 UNITS Qty. P/N Description 6 ............ 491010 ............ RUBBER LATCH ASSY.1 ............ EM200293A .... PADDLE ARM TOW SIDE1 ............ EM200294A .... PADDLE ARM CENTER...
Page 42 - NAMEPLATE AND DECALS
PAGE 42 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) NAMEPLATE AND DECALS
Page 43 - DECAL, TOWING INSTRUCTIONS
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 43 NO. PART NO. PART NAME QTY. REMARKS 1 DCL151 DECAL, TOWING INSTRUCTIONS 2 2 EM948630 DECAL, PUSH TO STOP 1 3 DCL160A DECAL, CRUSH WARNING 2 4 515275 DECAL, WHITEMAN LOGO (SMALL) 3 5 504713 DECAL, SAFETY INSTRUCTIO...
Page 45 - PADDLE ARM, CENTER TOW END
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 45 NO. PART NO. PART NAME QTY. REMARKS 2 492584 NUT, LOCK 1/2" 8 3 EM200295A PADDLE ARM, CENTER TOW END 1 5 EM200292 INSERT, PADDLE ARM 8 6 EM200293A PADDLE ARM, TOW END 1 7 6109170 WASHER, FLAT 1/2" 8 8 EM20...
Page 46 - PLASTIC MIXING DRUM ASSY.
PAGE 46 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) PLASTIC MIXING DRUM ASSY.
Page 53 - SPRING
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 53 EFFECTIVE NOVEMBER 2002- THE PADDLE SHAFTCONNECTOR PIN HAS BEEN DISCONTIUED. THE COUPLERIS NOW KEYED TO THE PADDLE SHAFT. NOTE PADDLE SHAFT ASSY. (PLASTIC/STEEL) NO PART NO PART NAME QTY. REMARKS 1 3061 SPACER, TH...
Page 59 - GRATE LATCH
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 59 FRAME 2 ASSY. 5 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE) S/N HD27964 T0 GE210000 APRIL 1999 — MAY 2000 NO PART NO PART NAME QTY. REMARK 1 13212 GROMMET ............................................... 1 ...............
Page 62 - PLASTIC ENGINE COVER ASSY.
PAGE 62 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) PLASTIC ENGINE COVER ASSY. S/N KA26943 TO GE 210000 JANUARY 1996 TO MAY 2000
Page 64 - STEEL ENGINE COVER ASSY.
PAGE 64 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) STEEL ENGINE COVER ASSY. GE 210001 AND ABOVE MAY 2000 AND ABOVE
Page 65 - HINGE
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 65 GE 210001 AND ABOVE MAY 2000 AND ABOVE NO. PART NO. PART NAME QTY. REMARKS 1 511580 ENGINE COVER-STEEL ...................................... 1 .......... S/N GE210001 AND ABOVE 2 509726 HINGE 2 3 491010 RUBBER LA...
Page 67 - STARTER MOUNT
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 67 NO. PART NO. PART NAME QTY. REMARKS 2 0166 A WASHER, LOCK 3/8 MED. ..................................... 2 ................ REPLACES 492624 4 EM963610 CAPSCREW 3/8" NCX1-1/4" G8 ..............................
Page 71 - PLATE
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 71 NO. PART NO. PART NAME QTY. REMARKS 1 3364 ENGINE, HONDA 13HP GX390U1QA2 1 2 203148 TUBE, EXHAUST 1 3 203123F PLATE 1 4 491797 RIVET, ID PLATE 4 5 29174-001 KNOB-MUSHROOM 1 6 29173-001 SWITCH, PUSH-PULL W/O KNOB 1...
Page 73 - COLLAR B, AIR CLEANER
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 73 NO. PART NO. PART NAME QTY. REMARKS 1 16271ZE2000 GASKET, ELBOW 1 2 17210ZE3010 ELEMENT, AIR CLEANER ................ 1 ........ INCLUDES ITEMS W/ # 3 # 17218ZE3000 FILTER, OUTER 1 4 17231ZE3W01 COVER, AIR CLEANER...
Page 75 - CAMSHAFT ASSEMBLY
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 75 NO. PART NO. PART NAME QTY. REMARKS 1 14100ZF6W0 CAMSHAFT ASSEMBLY ............................... 1 ................ INCLUDES ITEMS W/ * ......................................................................
Page 77 - CLIP, PISTON PIN 20MM
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 77 NO. PART NO. PART NAME QTY. REMARKS 1 13010ZF6003 RING SET, PISTON (STD.) 1 1 13010ZF6005 RING SET, PISTON (STD.) 1 1 13011ZF6003 RING SET, PISTON (OS 0.25), OPT. 1 1 13011ZF6005 RING SET, PISTON (OS 0.25), OPT. 1...
Page 79 - GASKET, OIL FILLER CAP
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 79 NO. PART NO. PART NAME QTY. REMARKS 1 * 06165ZE3000 GOVERNOR KIT (OPIONAL) ........................... 1 ......... INCLUDES ITEMS W/ # 2 11300ZE3602 COVER ASSY., CRANKCASE (Q TYPE) ........ 1 ......... INC...
Page 83 - PART NAME
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 83 NO. PART NO. PART NAME QTY. REMARKS 1 12000ZF6W12 BARREL ASSY., CYL. ALERT OIL .......... 1 ....... INCLUDES ITEMS W/ * ........................................................................... SN 302057...
Page 85 - GASKET, CYLINDER HEAD
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 85 NO. PART NO. PART NAME QTY. REMARKS 1 12200ZF6W01 CYLINDER HEAD ............................................ 1 ......... INCLUDES ITEMS W/ * 1 ◊◊◊◊◊ 12200ZF6406 CYLINDER HEAD .................................
Page 87 - SHROUD
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 87 NO. PART NO. PART NAME QTY. REMARKS 1 16731ZE2003 CLIP, TUBE 1 2 19610ZE3010ZA COVER, FAN *R280*, RED 1 3 19631ZE3W00 SHROUD 1 4 32197ZH8003 SUB-HARNESS ........................................... 1 .........
Page 89 - FLYWHEEL
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 89 NO. PART NO. PART NAME QTY. REMARKS 1 19511ZE3000 FAN, COOLING 1 2 28450ZE3W11 PULLEY, STARTER (SCREEN GRID) 1 4 31100ZE3701 FLYWHEEL 1 6 90201ZE3790 NUT, SPECIAL 16MM .................................. 1 ...
Page 91 - CAP ASSEMBLY, NOISE SUPPRESSOR
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 91 NO. PART NO. PART NAME QTY. REMARKS 1 30500ZF6W02 COIL ASSEMBLY, IGNITION ....................... 1 ......... REPLACES 305007E2023 1 ◊◊◊◊◊ 30500ZF6W02 COIL ASSEMBLY, IGNITION ....................... 1 .......
Page 93 - FLOAT SET
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 93 CARBURETOR ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 #% 16010ZE2812 GASKET SET .............................................. 1 ......... INCLUDES ITEM W/& 2 * 16011ZA0931 VALVE SET, FLOAT 1 3 * 16013ZA0931 ...
Page 95 - PROTECTOR, EXHAUST PIPE
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 95 NO. PART NO. PART NAME QTY. REMARKS 1 18310ZE2W61 MUFFLER 100DB 1 2 18320ZE2W61 PROTECTOR, MUFFLER 1 3 18323ZE3W40 PROTECTOR, EXHAUST PIPE 1 4 18330ZE2W00 PIPE, EXHAUST 1 5 18331ZE3810 CAP, MUFFLER 1 5 ◊◊◊...
Page 97 - PULLEY, RECOIL STARTER
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 97 NO. PART NO. PART NAME QTY. REMARKS 1 28400ZE3W01ZA STARTER ASSY., RECOIL *R8*, RED. ............. 1 ....... INCLUDES ITEMS W/ * 1 ◊◊◊◊◊ 28400ZE3W01ZP STARTER ASSY., RECOIL *R280*, RED. ......... 1 ..........
Page 99 - SPRING, THROTTLE RETURN
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 99 NO. PART NO. PART NAME QTY. REMARKS 2 16551ZE3000 ARM, GOVERNOR 1 3 16555ZE3000 ROD, GOVERNOR 1 4 16561ZE3000 SPRING, GOVERNOR 1 5 16562ZE3000 SPRING, THROTTLE RETURN 1 6 16570ZE3W20 CONTROL ASSEMBLY, REMOTE ........
Page 102 - HONDA GX390K1QA2 — GASKET KIT ASSY.
PAGE 102 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) HONDA GX390K1QA2 — GASKET KIT ASSY.
Page 106 - TERMS AND CONDITIONS OF SALE — PARTS
PAGE 106 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) PAYMENT TERMS Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiq...
Page 108 - OPERATION AND PARTS MANUAL; Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; UNITED STATES; CANADA
OPERATION AND PARTS MANUAL Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office MQ Parts Department 18910 Wilmington Ave.Carson, CA 90746 Contact: [email protected] Tel. (800) 421-1244Fax (800) 537-3927 800-...
