Page 2 - MQ STREET PRO 1 CE SAW — PROPOSITION 65 WARNING
PAGE 2 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) Engine exhaust and some of its constituents, and some dust created of California to cause cancer, birthdefects and other reproductive harm. by power sanding, sawing, grinding, drilling and other construction activities contains ch...
Page 3 - SILICOSIS WARNING; MQ STREET PRO 1 CE SAW — SILICOSIS/RESPIRATORY WARNINGS
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 3 Grinding/cutting/drilling of masonry, concrete, metal andother materials with silica in their composition may giveoff dust or mists containing crystalline silica. Silica is abasic component of sand, quartz, brick clay, granite and...
Page 4 - MQ STREET PRO 1 CE SAW — TABLE OF CONTENTS; MQ — STREET PRO 1 CE SAW; Specifications and
PAGE 4 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) MQ STREET PRO 1 CE SAW — TABLE OF CONTENTS Proposition 65 Warning ............................................. 2Silicosis/Respiratory Warnings .................................. 3Table Of Contents ...................................
Page 5 - Ordering parts has never been easier!; Choose from three easy options:; WE ACCEPT ALL MAJOR CREDIT CARDS!; Order via Internet; Order; internet; Fax; International Customers; PARTS ORDERING PROCEDURES
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 5 www .m ultiquip .com Ordering parts has never been easier! Choose from three easy options: WE ACCEPT ALL MAJOR CREDIT CARDS! When ordering parts, please supply: ❒ ❒ ❒ ❒ ❒ Dealer Account Number ❒ ❒ ❒ ❒ ❒ Dealer Name and Address ❒ ❒...
Page 6 - NOTES
PAGE 6 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) NOTES
Page 7 - MQ STREET PRO 1 CE SAW — SAFETY MESSAGE ALERT SYMBOLS; NOTE
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 7 MQ STREET PRO 1 CE SAW — SAFETY MESSAGE ALERT SYMBOLS Safety precautions should be followed at all times when operatingthis equipment. Failure to read, understand and comply with theSafety Messages and Operating Instructions could...
Page 8 - This
PAGE 8 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) Accidental Starting ALWAYS place the engine ON/OFF switch in the OFF position, when the saw is not in use. Over Speed Conditions NEVER tamper with the factory settings of the engine governor. Personal injury and damageto the engin...
Page 9 - MQ STREET PRO 1 CE SAW — RULES FOR SAFE OPERATION; WARNING
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 9 The following safety guidelines should always be used whenoperating the SP 1. SAFETY ■ DO NOT operate or service this equipment before reading this entire manual. Themanual must be kept available and accessibleto the operator. ■ T...
Page 11 - Figure 1. SP 1 Decals; ALWAYS
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 11 Figure 1. SP 1 Decals MQ STREET PRO 1 CE SAW — RULES FOR SAFE OPERATION EMERGENCIES ■ ALWAYS know the location o f t h e n e a r e s t f i r e extinguisher. ■ ALWAYS know the location of the nearest first aid kit. ■ In emergencie...
Page 12 - MQ STREET PRO 1 CE SAW — SPECIFICATIONS (SAW); Figure 2. SP 1 Dimensions; Side View; lf
PAGE 12 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) MQ STREET PRO 1 CE SAW — SPECIFICATIONS (SAW) Figure 2. SP 1 Dimensions Side View Front View A C B F G D E * Vibration (at handle) results with SP1 Saw cutting concrete at a depth of 1-1/2 inches (38.1 mm) with an 18" (45.7 c...
Page 13 - MQ STREET PRO 1 CE SAW — SPECIFICATIONS (ENGINE)
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 13 MQ STREET PRO 1 CE SAW — SPECIFICATIONS (ENGINE) ) e n i g n E ( s n o i t a c i f i c e p S . 2 e l b a T e n i g n E l e d o M A D N O H 2 T W Q 1 U 0 9 3 X G / 2 T W Q 1 K 0 9 3 X G e p y T e l g n i S , e k o r t s 4 d e l o ...
Page 14 - MQ STREET PRO 1 CE SAW — GENERAL INFORMATION; Figure 3. MQ STREET PRO 1 SAW
PAGE 14 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) MQ STREET PRO 1 CE SAW — GENERAL INFORMATION The MQ Whiteman SP1 series walk-behind saws are designed for wet cutting of concrete or asphalt utilizing Diamond Blades. These saws have been engineered for general and industrialflat...
Page 15 - MQ STREET PRO 1 CE SAW — CONTROLS & COMPONENTS
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 15 MQ STREET PRO 1 CE SAW — CONTROLS & COMPONENTS Figures 4 shows the location of the basic controls or componentsfor the SP 1. Listed below is a brief explanation of each control orcomponent. 1. Hand Grips/Handlebar – When oper...
Page 16 - MQ STREET PRO 1 CE SAW — BASIC ENGINE
PAGE 16 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) Figure 5. Engine Controls and Components Initial Servicing The engine (Figure 5) must be checked for proper lubrication andfilled with fuel prior to operation. Refer to the manufacturers enginemanual for instructions & detail...
Page 17 - MQ STREET PRO 1 CE SAW — PREPARATION/PRE-INSPECTION; Warning; UPPER LIMIT
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 17 MQ STREET PRO 1 CE SAW — PREPARATION/PRE-INSPECTION PREPARATION / PRE-INSPECTION 1. Read and fully understand this manual, the safety intructions in particular, andthe engine manufacturer's manualsupplied with the saw. 2. Select ...
Page 19 - A commonly located hole on the diamond; MQ STREET PRO 1 CE SAW — BLADES
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 19 Failure to thoroughly inspect the diamond blade (Figure 11)for operational safety could result in damage to the blade orthe saw, and may cause injury to the user or others in theoperating area. Discard damaged or worn blades andr...
Page 20 - MQ STREET PRO 1 CE SAW — BLADE PLACEMENT; TYPE
PAGE 20 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) WARNING Failure to thoroughly inspect thediamond blade for operational safetycould result in damage to the bladesor the saw and may cause injury tothe user or others in the operatingarea. 2. Blade Guard - Pivot the blade guard fr...
Page 21 - Blade Removal and Replacement; DO NOT
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 21 MQ STREET PRO 1 CE SAW — BLADE PLACEMENT 6. Inner Flange (Collar) - This flange is fixed upon the spindle. The inside surface of the flange must be free of debris andpermit a tight closure on the surface of the blade. WARNING Dro...
Page 22 - MQ STREET PRO 1 CE SAW — RAISE/LOWER AND DEPTH STOP; Raise/Lower and Depth Stop; Adjusting Hand Crank Assembly; Setting the Depth Stop; Lift the Adjusting Hand Crank to unlock (disengage) the
PAGE 22 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) MQ STREET PRO 1 CE SAW — RAISE/LOWER AND DEPTH STOP Raise/Lower and Depth Stop The saw is equipped with a Raise/Lower and Depth StopAssembly that is supported by the following components. (Figure14) Figure 14. Cutting Depth - Rai...
Page 23 - MQ STREET PRO 1 CE SAW — INITIAL START-UP
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 23 MQ STREET PRO 1 CE SAW — INITIAL START-UP DO NOT attempt to operate the saw until t h i s m a n u a l h a s b e e n r e a d a n dthoroughly understood. Engine operatingsteps may vary. See included enginemanufacturer's operating m...
Page 24 - MQ STREET PRO 1 CE SAW — INITIAL START-UP
PAGE 24 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) 7. Grasp the starter grip (Figure 22) and slowly pull it out. The resistance becomes the hardest at the compression point.Pull the starter grip briskly and smoothly for starting. Figure 22. Starter Grip 9. Before the saw is place...
Page 25 - MQ STREET PRO 1 CE SAW — OPERATION
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 25 MQ STREET PRO 1 CE SAW — OPERATION ALWAYS keep clear of rotating or moving parts while operating this equipment. WARNING 4. When blade has reached full cutting depth, slowly walk behind the saw at a rate that will allow the engin...
Page 26 - Restarting After Intervention
PAGE 26 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) MQ STREET PRO 1 CE SAW — OPERATION Restarting After Intervention If cutting is interrupted where the engine stops or is turned offwhile the blade is still in the cut: a. Turn Engine Off switches to "OFF" b. Raise the blad...
Page 27 - MQ STREET PRO 1 CE SAW — MAINTENANCE
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 27 Drive Belt Refer to page 16 of this manual for Drive Belt adjustmentprocedures and Removal and Replacement procedures. See the engine manual supplied with yourmachine for appropriate enginemaintenance schedule and troubleshooting...
Page 29 - MQ STREET PRO 1 CE SAW — OPTIONAL WATER TANK; Mount the Tank Shelf to the frame using hardware items 7, 9,; After determining the correct spacer length, place the spac-; Figure 26. Hose and Clamps; Replace the hard plastic tube back into the Water Tank valve.
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 29 MQ STREET PRO 1 CE SAW — OPTIONAL WATER TANK 1 6 8 7 9 11 12 10 13 WATER TANK KIT (OPTION) 1. Locate all parts listed in the parts list (see page 45). 2. Slide the Tank Shelf (item 1, Figure 25) over the top of the engine so the ...
Page 30 - so it securely holds the tank onto the Shelf.; Figure 27. Water Tank Position
PAGE 30 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) MQ STREET PRO 1 CE SAW — OPTIONAL WATER TANK 9 Place the Water Tank (with the hose assembled), onto theTank Shelf so the valve and hose are resting in the notch ofthe top of the Tank Shelf. (Figure 27) 10. Place the Bungee Cord (...
Page 31 - MQ STREET PRO 1 CE SAW —
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 31 MQ STREET PRO 1 CE SAW — TROUBLESHOOTING (SAW) G N I T O O H S E L B U O R T E D A L B . 5 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S . g n it t u c s p o t s r o s w o l s e d a l B g n i e b l a i r e...
Page 34 - REMARKS; EXPLANATION OF CODE IN REMARKS COLUMN
PAGE 34 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) The contents and part numbers listed in the parts section aresubject to change without notice . Multiquip does not guarantee the availibility of the parts listed. When ordering a part that has more than oneitem number listed, che...
Page 35 - MQ STREET PRO 1 CE SAW — SUGGESTED SPARE PARTS; MQ STREET PRO 1 CE CONCRETE/ASPHALT SAW; SUGGESTED SPARE PARTS
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 35 MQ STREET PRO 1 CE SAW — SUGGESTED SPARE PARTS MQ STREET PRO 1 CE CONCRETE/ASPHALT SAW 1 TO 3 UNITS WITH HONDA GX390K1QWT2/GX390U1QWT2 ENGINES 1 to 3 Units Qty. ...... P/N ........................... Description 3 20478 ............
Page 36 - DECALS
PAGE 36 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) MQ STREET PRO 1 SAW — DECALS DECALS En gin e ex ha us t an d so me of its co ns titu en ts, an ds om ed us tc rea ted of Ca lifo rni a to ca us e ca nc er, bir th de fec ts an d oth er rep rod uc tiv eh arm . by po we rs an din g...
Page 37 - PART NAME; DECAL, MQ DIAMONDBACK
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 37 MQ STREET PRO 1 CE SAW — DECALS DECALS NO. PART NO. PART NAME QTY. REMARKS 1 35137 DECAL, WARNING, READ MANUAL1 .......... SAFETY ITEM 2 20525 DECAL, PROP 65 WARNING ......... 1 .......... SAFETY ITEM 3 13118 DECAL, POWDER COATED...
Page 38 - ENGINE, BELTS AND PULLEYS
PAGE 38 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) MQ STREET PRO 1 CE SAW — ENGINE, BELTS AND PULLEYS ENGINE, BELTS AND PULLEYS
Page 40 - UNDERCARRIAGE ASSY
PAGE 40 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) UNDERCARRIAGE ASSY MQ STREET PRO 1 CE SAW — UNDERCARRIAGE ASSY.
Page 42 - BLADE ASSEMBLY & WATER SYSTEM
PAGE 42 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) MQ STREET PRO 1 CE SAW — BLADE ASSEMBLY & WATER SYSTEM BLADE ASSEMBLY & WATER SYSTEM 1 PULLEY ASSEMBLY.SEE PAGE 30. 1 33 34 40 37 41 36 1 2 2 3 3 4 4 5 7 6 8 11 13 14 22 24 25 2 21 27 16 16 18 19 20 17 26 28 26 25 30 32 3...
Page 44 - POINTER ASSEMBLY
PAGE 44 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) MQ STREET PRO 1 CE SAW — POINTER ASSEMBLY POINTER ASSEMBLY 1 2 3 7 8 4 6 5 5
Page 45 - INDICATOR ASSEMBLY
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 45 MQ STREET PRO 1 CE SAW — POINTER ASSEMBLY POINTER ASSEMBLY NO. PART NO. PART NAME QTY. REMARKS 1 21017 SCREW, POINTER ARM 1 2 29043-001 WHEEL, POINTER 1 3 1007 NUT, HEX JAM 3/8 - 16 2 4 1456 NUT, HEX FINISH 3/8 - 16 2 5 10133 NUT...
Page 51 - SPRING, WEIGHT RETURN
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 51 HONDA GX390K1QWT2/GX390U1QWT2 ENG.— CAMSHAFT ASSY. CAMSHAFT ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 14100ZF6W01 CAMSHAFT ASSEMBLY .......................... 1 ......... INCLUDES ITEM W/ * 2 14410ZE3013 ROD, PUSH 2 3 14431ZE20...
Page 53 - CARBURETOR, GASKET SET
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 53 HONDA GX390K1QWT2/GX390U1QWT2 ENG.— CARBURETOR ASSY. CARBURETOR ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 16010ZE2812 CARBURETOR, GASKET SET 1 INCLUDES ITEMS W/ + 2$ 16011ZA0931 VALVE SET, FLOAT 1 3$ 16013ZA0931 FLOAT SET 1 4$ ...
Page 55 - SPRING, THROTTLE RETURN
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 55 HONDA GX390K1QWT2/GX390U1QWT2 ENG.— CONTROL ASSY. CONTROL ASSY. NO. PART NO. PART NAME QTY. REMARKS 2 16551ZE3000 ARM, GOVERNOR 1 3 16555ZE3000 ROD, GOVERNOR 1 4 16561ZE3000 SPRING, GOVERNOR 1 5 16562ZE3000 SPRING, THROTTLE RETUR...
Page 56 - CRANKCASE COVER ASSY.
PAGE 56 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) CRANKCASE COVER ASSY. HONDA GX390K1QWT2/GX390U1QWT2 ENG.— CRANKCASE ASSY.
Page 57 - GASKET, OIL FILLER CAP
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 57 HONDA GX390K1QWT2/GX390U1QWT2 ENG.— CRANKCASE ASSY. CRANKCASE COVER ASSY. NO. PART NO. PART NAME QTY. REMARKS 2 11300ZE3602 COVER ASSY., CRANKCASE ......................... 1 ................ S/N 3287256 AND BELOW ..................
Page 60 - CYLINDER BARREL ASSY.
PAGE 60 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) CYLINDER BARREL ASSY. HONDA GX390K1QWT2/GX390U1QWT2 ENG.— CYLINDER BARREL ASSY.
Page 63 - GASKET, CYLINDER HEAD
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 63 HONDA GX390K1QWT2/GX390U1QWT2 ENG.— CYLINDER HEAD ASSY. CYLINDER HEAD ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 12200ZF6W01 CYLINDER HEAD ............................................. 1 ................ INCLUDES ITEMS W/ * 1 ◊◊...
Page 65 - SHROUD
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 65 HONDA GX390K1QWT2/GX390U1QWT2 ENG.— FAN COVER ASSY. FAN COVER ASSY. NO. PART NO. PART NAME QTY. REMARKS 4 16731ZE2003 CLIP, TUBE 1 7 19610ZE3010ZB COVER, FAN *NH1* (BLACK) 1 10 19631ZE3W00 SHROUD 1 13 36100ZH7003 SWITCH ASSY., EN...
Page 67 - FLYWHEEL
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 67 HONDA GX390K1QWT2/GX390U1QWT2 ENG.— FLYWHEEL ASSY. FLYWHEEL ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 19511ZE3000 FAN, COOLING 1 3 28450ZE3W11 PULLEY, STARTER (SCREEN GRID) 1 7 31100ZE3701 FLYWHEEL 1 10 90201ZE3V00 NUT, SPECIAL...
Page 69 - GASKET, FUEL FILLER CAP
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 69 HONDA GX390K1QWT2/GX390U1QWT2 ENG.— FUEL TANK ASSY. FUEL TANK ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 16854ZH8000 RUBBER, SUPPORTER (107MM) 1 3 16955ZE1000 JOINT, FUEL TANK 1 6 17510ZE3010ZB TANK, FUEL *NH1* 1 6 ◊◊◊◊◊ 17510ZE...
Page 73 - MUFFLER
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 73 HONDA GX390K1QWT2/GX390U1QWT2 ENG.— MEFFLER ASSY. MUFFLER ASSY. NO. PART NO. PART NAME QTY. REMARKS 2 18310ZE2W61 MUFFLER 1 3 18320ZE2W61 PROTECTOR, MUFFLER 1 5 18330ZE2W00 PIPE, EX. 1 6 18331ZE3810 CAP, MUFFLER 1 6 ◊◊◊◊◊ 18331ZE...
Page 77 - PULLEY, RECOIL STARTER
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 77 HONDA GX390K1QWT2/GX390U1QWT2 ENG.— RECOIL STATER ASSY. RECOIL STARTER ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 28400ZE3W01ZB STARTER ASSY., RECOIL *NH1* (BLACK) .............. 1 ...... INCLUDES ITEMS W/ * 2 * 28410ZE3W01ZB CA...
Page 80 - TERMS AND CONDITIONS OF SALE — PARTS
PAGE 80 — SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) PAYMENT TERMS Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect orprepaid with the charges added to the invoice.All shipments are F.O.B. point of origin.Multiquip’s responsibility...
Page 81 - NOTE PAGE
SP 1 SAW CE— OPERATION AND PARTS MANUAL — REV. #3 (06/09/08) — PAGE 81 NOTE PAGE
Page 82 - OPERATION AND PARTS MANUAL; Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; UNITED STATES
OPERATION AND PARTS MANUAL Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING © COPYRIGHT 2008, MULTIQUIP INC. Multiquip Inc, the MQ logo and the Diamond Back logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or a...
